[PATCH 18/24] scsi: ncr53c8xx: remove leading spaces before tabs

From: Hui Tang
Date: Sat May 22 2021 - 04:41:06 EST


There are a few leading spaces before tabs and remove it by running
the following commard:

$ find . -name '*.[ch]' | xargs sed -r -i 's/^[ ]+\t/\t/'

Signed-off-by: Hui Tang <tanghui20@xxxxxxxxxx>
---
drivers/scsi/ncr53c8xx.c | 32 ++++++++++++++++----------------
drivers/scsi/ncr53c8xx.h | 2 +-
2 files changed, 17 insertions(+), 17 deletions(-)

diff --git a/drivers/scsi/ncr53c8xx.c b/drivers/scsi/ncr53c8xx.c
index c76e9f0..0024bc5 100644
--- a/drivers/scsi/ncr53c8xx.c
+++ b/drivers/scsi/ncr53c8xx.c
@@ -2214,7 +2214,7 @@ static struct script script0 __initdata = {
RADDR (scratcha),
RADDR (scratcha),
SCR_RETURN,
- 0,
+ 0,
SCR_JUMP ^ IFTRUE (IF (SCR_STATUS)),
PADDR (status),
SCR_JUMP ^ IFTRUE (IF (SCR_COMMAND)),
@@ -3760,7 +3760,7 @@ static void __init ncr_prepare_setting(struct ncb *np)

np->maxwide = (np->features & FE_WIDE)? 1 : 0;

- /*
+ /*
* Guess the frequency of the chip's clock.
*/
if (np->features & FE_ULTRA)
@@ -3770,7 +3770,7 @@ static void __init ncr_prepare_setting(struct ncb *np)

/*
* Get the clock multiplier factor.
- */
+ */
if (np->features & FE_QUAD)
np->multiplier = 4;
else if (np->features & FE_DBLR)
@@ -4541,7 +4541,7 @@ static void ncr_start_reset(struct ncb *np)
{
if (!np->settle_time) {
ncr_reset_scsi_bus(np, 1, driver_setup.settle_delay);
- }
+ }
}

/*==========================================================
@@ -5204,11 +5204,11 @@ static void ncr_chip_reset(struct ncb *np, int delay)

void ncr_init (struct ncb *np, int reset, char * msg, u_long code)
{
- int i;
+ int i;

- /*
+ /*
** Reset chip if asked, otherwise just clear fifos.
- */
+ */

if (reset) {
OUTB (nc_istat, SRST);
@@ -7880,18 +7880,18 @@ static unsigned __init ncrgetfreq (struct ncb *np, int gen)
udelay(100); /* count ms */
}
OUTB (nc_stime1, 0); /* disable general purpose timer */
- /*
- * set prescaler to divide by whatever 0 means
- * 0 ought to choose divide by 2, but appears
- * to set divide by 3.5 mode in my 53c810 ...
- */
- OUTB (nc_scntl3, 0);
+ /*
+ * set prescaler to divide by whatever 0 means
+ * 0 ought to choose divide by 2, but appears
+ * to set divide by 3.5 mode in my 53c810 ...
+ */
+ OUTB (nc_scntl3, 0);

if (bootverbose >= 2)
printk ("%s: Delay (GEN=%d): %u msec\n", ncr_name(np), gen, ms);
- /*
- * adjust for prescaler, and convert into KHz
- */
+ /*
+ * adjust for prescaler, and convert into KHz
+ */
return ms ? ((1 << gen) * 4340) / ms : 0;
}

diff --git a/drivers/scsi/ncr53c8xx.h b/drivers/scsi/ncr53c8xx.h
index fa14b5c..b1567e8 100644
--- a/drivers/scsi/ncr53c8xx.h
+++ b/drivers/scsi/ncr53c8xx.h
@@ -757,7 +757,7 @@ struct ncr_reg {
#define IRQM 0x08 /* mod: irq mode (1 = totem pole !) */
#define STD 0x04 /* cmd: start dma mode */
#define IRQD 0x02 /* mod: irq disable */
- #define NOCOM 0x01 /* cmd: protect sfbr while reselect */
+ #define NOCOM 0x01 /* cmd: protect sfbr while reselect */
/* bits 0-1 rsvd for C1010 */

/*3c*/ u32 nc_adder;
--
2.8.1