[PATCH 4.14 068/323] drm/msm/mdp5: Configure PP_SYNC_HEIGHT to double the vtotal

From: Greg Kroah-Hartman
Date: Thu May 20 2021 - 06:32:00 EST


From: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>

[ Upstream commit 2ad52bdb220de5ab348098e3482b01235d15a842 ]

Leaving this at a close-to-maximum register value 0xFFF0 means it takes
very long for the MDSS to generate a software vsync interrupt when the
hardware TE interrupt doesn't arrive. Configuring this to double the
vtotal (like some downstream kernels) leads to a frame to take at most
twice before the vsync signal, until hardware TE comes up.

In this case the hardware interrupt responsible for providing this
signal - "disp-te" gpio - is not hooked up to the mdp5 vsync/pp logic at
all. This solves severe panel update issues observed on at least the
Xperia Loire and Tone series, until said gpio is properly hooked up to
an irq.

Suggested-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
Signed-off-by: Marijn Suijten <marijn.suijten@xxxxxxxxxxxxxx>
Reviewed-by: AngeloGioacchino Del Regno <angelogioacchino.delregno@xxxxxxxxxxxxxx>
Link: https://lore.kernel.org/r/20210406214726.131534-2-marijn.suijten@xxxxxxxxxxxxxx
Signed-off-by: Rob Clark <robdclark@xxxxxxxxxxxx>
Signed-off-by: Sasha Levin <sashal@xxxxxxxxxx>
---
drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c | 10 +++++++++-
1 file changed, 9 insertions(+), 1 deletion(-)

diff --git a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c
index 60790df91bfa..397e71481129 100644
--- a/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c
+++ b/drivers/gpu/drm/msm/mdp/mdp5/mdp5_cmd_encoder.c
@@ -78,9 +78,17 @@ static int pingpong_tearcheck_setup(struct drm_encoder *encoder,
| MDP5_PP_SYNC_CONFIG_VSYNC_IN_EN;
cfg |= MDP5_PP_SYNC_CONFIG_VSYNC_COUNT(vclks_line);

+ /*
+ * Tearcheck emits a blanking signal every vclks_line * vtotal * 2 ticks on
+ * the vsync_clk equating to roughly half the desired panel refresh rate.
+ * This is only necessary as stability fallback if interrupts from the
+ * panel arrive too late or not at all, but is currently used by default
+ * because these panel interrupts are not wired up yet.
+ */
mdp5_write(mdp5_kms, REG_MDP5_PP_SYNC_CONFIG_VSYNC(pp_id), cfg);
mdp5_write(mdp5_kms,
- REG_MDP5_PP_SYNC_CONFIG_HEIGHT(pp_id), 0xfff0);
+ REG_MDP5_PP_SYNC_CONFIG_HEIGHT(pp_id), (2 * mode->vtotal));
+
mdp5_write(mdp5_kms,
REG_MDP5_PP_VSYNC_INIT_VAL(pp_id), mode->vdisplay);
mdp5_write(mdp5_kms, REG_MDP5_PP_RD_PTR_IRQ(pp_id), mode->vdisplay + 1);
--
2.30.2