[PATCH v2 1/6] dt-bindings: mux: Convert reg-mux DT bindings to YAML
From: Kishon Vijay Abraham I
Date: Mon May 17 2021 - 02:18:22 EST
Convert reg-mux DT bindings to YAML. Move the examples provided in
reg-mux.txt to mux-controller.txt and remove reg-mux.txt
Signed-off-by: Kishon Vijay Abraham I <kishon@xxxxxx>
---
.../bindings/mux/mux-controller.txt | 113 ++++++++++++++-
.../devicetree/bindings/mux/reg-mux.txt | 129 ------------------
.../devicetree/bindings/mux/reg-mux.yaml | 47 +++++++
3 files changed, 159 insertions(+), 130 deletions(-)
delete mode 100644 Documentation/devicetree/bindings/mux/reg-mux.txt
create mode 100644 Documentation/devicetree/bindings/mux/reg-mux.yaml
diff --git a/Documentation/devicetree/bindings/mux/mux-controller.txt b/Documentation/devicetree/bindings/mux/mux-controller.txt
index 4f47e4bd2fa0..6f1e83367d52 100644
--- a/Documentation/devicetree/bindings/mux/mux-controller.txt
+++ b/Documentation/devicetree/bindings/mux/mux-controller.txt
@@ -38,7 +38,7 @@ mux-ctrl-specifier typically encodes the chip-relative mux controller number.
If the mux controller chip only provides a single mux controller, the
mux-ctrl-specifier can typically be left out.
-Example:
+Example 1:
/* One consumer of a 2-way mux controller (one GPIO-line) */
mux: mux-controller {
@@ -64,6 +64,8 @@ because there is only one mux controller in the list. However, if the driver
for the consumer node in fact asks for a named mux controller, that name is of
course still required.
+Example 2:
+
/*
* Two consumers (one for an ADC line and one for an i2c bus) of
* parallel 4-way multiplexers controlled by the same two GPIO-lines.
@@ -116,6 +118,115 @@ course still required.
};
};
+Example 3:
+
+The parent device of mux controller is not a syscon device.
+
+&i2c0 {
+ fpga@66 { // fpga connected to i2c
+ compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
+ "simple-mfd";
+ reg = <0x66>;
+
+ mux: mux-controller {
+ compatible = "reg-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
+ <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */
+ };
+ };
+};
+
+mdio-mux-1 {
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 0>;
+ mdio-parent-bus = <&emdio1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@8 {
+ reg = <0x8>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ..
+ ..
+};
+
+mdio-mux-2 {
+ compatible = "mdio-mux-multiplexer";
+ mux-controls = <&mux 1>;
+ mdio-parent-bus = <&emdio2>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ mdio@0 {
+ reg = <0x0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ mdio@1 {
+ reg = <0x1>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ };
+
+ ..
+ ..
+};
+
+Example 4:
+
+The parent device of mux controller is syscon device.
+
+syscon {
+ compatible = "syscon";
+
+ mux: mux-controller {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+
+ mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */
+ <0x3 0x40>, /* 1: reg 0x3, bit 6 */
+ idle-states = <MUX_IDLE_AS_IS>, <0>;
+ };
+};
+
+video-mux {
+ compatible = "video-mux";
+ mux-controls = <&mux 0>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ports {
+ /* inputs 0..3 */
+ port@0 {
+ reg = <0>;
+ };
+ port@1 {
+ reg = <1>;
+ };
+ port@2 {
+ reg = <2>;
+ };
+ port@3 {
+ reg = <3>;
+ };
+
+ /* output */
+ port@4 {
+ reg = <4>;
+ };
+ };
+};
Mux controller nodes
--------------------
diff --git a/Documentation/devicetree/bindings/mux/reg-mux.txt b/Documentation/devicetree/bindings/mux/reg-mux.txt
deleted file mode 100644
index 4afd7ba73d60..000000000000
--- a/Documentation/devicetree/bindings/mux/reg-mux.txt
+++ /dev/null
@@ -1,129 +0,0 @@
-Generic register bitfield-based multiplexer controller bindings
-
-Define register bitfields to be used to control multiplexers. The parent
-device tree node must be a device node to provide register r/w access.
-
-Required properties:
-- compatible : should be one of
- "reg-mux" : if parent device of mux controller is not syscon device
- "mmio-mux" : if parent device of mux controller is syscon device
-- #mux-control-cells : <1>
-- mux-reg-masks : an array of register offset and pre-shifted bitfield mask
- pairs, each describing a single mux control.
-* Standard mux-controller bindings as decribed in mux-controller.txt
-
-Optional properties:
-- idle-states : if present, the state the muxes will have when idle. The
- special state MUX_IDLE_AS_IS is the default.
-
-The multiplexer state of each multiplexer is defined as the value of the
-bitfield described by the corresponding register offset and bitfield mask
-pair in the mux-reg-masks array.
-
-Example 1:
-The parent device of mux controller is not a syscon device.
-
-&i2c0 {
- fpga@66 { // fpga connected to i2c
- compatible = "fsl,lx2160aqds-fpga", "fsl,fpga-qixis-i2c",
- "simple-mfd";
- reg = <0x66>;
-
- mux: mux-controller {
- compatible = "reg-mux";
- #mux-control-cells = <1>;
- mux-reg-masks = <0x54 0xf8>, /* 0: reg 0x54, bits 7:3 */
- <0x54 0x07>; /* 1: reg 0x54, bits 2:0 */
- };
- };
-};
-
-mdio-mux-1 {
- compatible = "mdio-mux-multiplexer";
- mux-controls = <&mux 0>;
- mdio-parent-bus = <&emdio1>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@0 {
- reg = <0x0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mdio@8 {
- reg = <0x8>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- ..
- ..
-};
-
-mdio-mux-2 {
- compatible = "mdio-mux-multiplexer";
- mux-controls = <&mux 1>;
- mdio-parent-bus = <&emdio2>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- mdio@0 {
- reg = <0x0>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- mdio@1 {
- reg = <0x1>;
- #address-cells = <1>;
- #size-cells = <0>;
- };
-
- ..
- ..
-};
-
-Example 2:
-The parent device of mux controller is syscon device.
-
-syscon {
- compatible = "syscon";
-
- mux: mux-controller {
- compatible = "mmio-mux";
- #mux-control-cells = <1>;
-
- mux-reg-masks = <0x3 0x30>, /* 0: reg 0x3, bits 5:4 */
- <0x3 0x40>, /* 1: reg 0x3, bit 6 */
- idle-states = <MUX_IDLE_AS_IS>, <0>;
- };
-};
-
-video-mux {
- compatible = "video-mux";
- mux-controls = <&mux 0>;
- #address-cells = <1>;
- #size-cells = <0>;
-
- ports {
- /* inputs 0..3 */
- port@0 {
- reg = <0>;
- };
- port@1 {
- reg = <1>;
- };
- port@2 {
- reg = <2>;
- };
- port@3 {
- reg = <3>;
- };
-
- /* output */
- port@4 {
- reg = <4>;
- };
- };
-};
diff --git a/Documentation/devicetree/bindings/mux/reg-mux.yaml b/Documentation/devicetree/bindings/mux/reg-mux.yaml
new file mode 100644
index 000000000000..54583aafa9de
--- /dev/null
+++ b/Documentation/devicetree/bindings/mux/reg-mux.yaml
@@ -0,0 +1,47 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: "http://devicetree.org/schemas/mux/reg-mux.yaml#";
+$schema: "http://devicetree.org/meta-schemas/core.yaml#";
+
+title: Generic register bitfield-based multiplexer controller bindings
+
+maintainers:
+ - Peter Rosin <peda@xxxxxxxxxx>
+
+properties:
+ compatible:
+ enum:
+ - reg-mux
+ - mmio-mux
+
+ "#mux-control-cells": true
+
+ mux-reg-masks:
+ minItems: 2
+ maxItems: 32
+ description:
+ An array of register offset and pre-shifted bitfield mask pairs, each describing a
+ single mux control.
+
+ idle-states:
+ allOf:
+ - $ref: /schemas/types.yaml#/definitions/uint32-array
+
+required:
+ - compatible
+ - mux-reg-masks
+
+additionalProperties: false
+
+examples:
+ - |
+ serdes_ln_ctrl: mux {
+ compatible = "mmio-mux";
+ #mux-control-cells = <1>;
+ mux-reg-masks = <0x4080 0x3>, <0x4084 0x3>, /* SERDES0 lane0/1 select */
+ <0x4090 0x3>, <0x4094 0x3>, /* SERDES1 lane0/1 select */
+ <0x40a0 0x3>, <0x40a4 0x3>, /* SERDES2 lane0/1 select */
+ <0x40b0 0x3>, <0x40b4 0x3>, /* SERDES3 lane0/1 select */
+ <0x40c0 0x3>, <0x40c4 0x3>, <0x40c8 0x3>, <0x40cc 0x3>;
+ };
--
2.17.1