Re: [RFC PATCH v5 00/19] virtio/vsock: introduce SOCK_SEQPACKET support

From: Arseny Krasnov
Date: Wed Feb 24 2021 - 03:30:29 EST



On 24.02.2021 11:23, Stefano Garzarella wrote:
> On Wed, Feb 24, 2021 at 07:29:25AM +0300, Arseny Krasnov wrote:
>> On 23.02.2021 17:50, Stefano Garzarella wrote:
>>> On Mon, Feb 22, 2021 at 03:23:11PM +0100, Stefano Garzarella wrote:
>>>> Hi Arseny,
>>>>
>>>> On Thu, Feb 18, 2021 at 08:33:44AM +0300, Arseny Krasnov wrote:
>>>>> This patchset impelements support of SOCK_SEQPACKET for virtio
>>>>> transport.
>>>>> As SOCK_SEQPACKET guarantees to save record boundaries, so to
>>>>> do it, two new packet operations were added: first for start of record
>>>>> and second to mark end of record(SEQ_BEGIN and SEQ_END later). Also,
>>>>> both operations carries metadata - to maintain boundaries and payload
>>>>> integrity. Metadata is introduced by adding special header with two
>>>>> fields - message count and message length:
>>>>>
>>>>> struct virtio_vsock_seq_hdr {
>>>>> __le32 msg_cnt;
>>>>> __le32 msg_len;
>>>>> } __attribute__((packed));
>>>>>
>>>>> This header is transmitted as payload of SEQ_BEGIN and SEQ_END
>>>>> packets(buffer of second virtio descriptor in chain) in the same way as
>>>>> data transmitted in RW packets. Payload was chosen as buffer for this
>>>>> header to avoid touching first virtio buffer which carries header of
>>>>> packet, because someone could check that size of this buffer is equal
>>>>> to size of packet header. To send record, packet with start marker is
>>>>> sent first(it's header contains length of record and counter), then
>>>>> counter is incremented and all data is sent as usual 'RW' packets and
>>>>> finally SEQ_END is sent(it also carries counter of message, which is
>>>>> counter of SEQ_BEGIN + 1), also after sedning SEQ_END counter is
>>>>> incremented again. On receiver's side, length of record is known from
>>>>> packet with start record marker. To check that no packets were dropped
>>>>> by transport, counters of two sequential SEQ_BEGIN and SEQ_END are
>>>>> checked(counter of SEQ_END must be bigger that counter of SEQ_BEGIN by
>>>>> 1) and length of data between two markers is compared to length in
>>>>> SEQ_BEGIN header.
>>>>> Now as packets of one socket are not reordered neither on
>>>>> vsock nor on vhost transport layers, such markers allows to restore
>>>>> original record on receiver's side. If user's buffer is smaller that
>>>>> record length, when all out of size data is dropped.
>>>>> Maximum length of datagram is not limited as in stream socket,
>>>>> because same credit logic is used. Difference with stream socket is
>>>>> that user is not woken up until whole record is received or error
>>>>> occurred. Implementation also supports 'MSG_EOR' and 'MSG_TRUNC' flags.
>>>>> Tests also implemented.
>>>> I reviewed the first part (af_vsock.c changes), tomorrow I'll review
>>>> the rest. That part looks great to me, only found a few minor issues.
>>> I revieiwed the rest of it as well, left a few minor comments, but I
>>> think we're well on track.
>>>
>>> I'll take a better look at the specification patch tomorrow.
>> Great, Thank You
>>> Thanks,
>>> Stefano
>>>
>>>> In the meantime, however, I'm getting a doubt, especially with regard
>>>> to other transports besides virtio.
>>>>
>>>> Should we hide the begin/end marker sending in the transport?
>>>>
>>>> I mean, should the transport just provide a seqpacket_enqueue()
>>>> callbacl?
>>>> Inside it then the transport will send the markers. This is because
>>>> some transports might not need to send markers.
>>>>
>>>> But thinking about it more, they could actually implement stubs for
>>>> that calls, if they don't need to send markers.
>>>>
>>>> So I think for now it's fine since it allows us to reuse a lot of
>>>> code, unless someone has some objection.
>> I thought about that, I'll try to implement it in next version. Let's see...
> If you want to discuss it first, write down the idea you want to
> implement, I wouldn't want to make you do unnecessary work. :-)

Idea is simple, in iov iterator of 'struct msghdr' which is passed to

enqueue callback we have two fields: 'iov_offset' which is byte

offset inside io vector where next data must be picked and 'count'

which is rest of unprocessed bytes in io vector. So in seqpacket

enqueue callback if 'iov_offset' is 0 i'll send SEQBEGIN, and if

'count' is 0 i'll send SEQEND.

>
> Cheers,
> Stefano
>
>