Re: [PATCH v2 1/1] arm64: mm: correct the inside linear map boundaries during hotplug check

From: Pavel Tatashin
Date: Tue Feb 16 2021 - 09:37:54 EST


On Tue, Feb 16, 2021 at 2:36 AM Ard Biesheuvel <ardb@xxxxxxxxxx> wrote:
>
> On Tue, 16 Feb 2021 at 04:12, Anshuman Khandual
> <anshuman.khandual@xxxxxxx> wrote:
> >
> >
> >
> > On 2/16/21 1:21 AM, Pavel Tatashin wrote:
> > > On Mon, Feb 15, 2021 at 2:34 PM Ard Biesheuvel <ardb@xxxxxxxxxx> wrote:
> > >>
> > >> On Mon, 15 Feb 2021 at 20:30, Pavel Tatashin <pasha.tatashin@xxxxxxxxxx> wrote:
> > >>>
> > >>>> Can't we simply use signed arithmetic here? This expression works fine
> > >>>> if the quantities are all interpreted as s64 instead of u64
> > >>>
> > >>> I was thinking about that, but I do not like the idea of using sign
> > >>> arithmetics for physical addresses. Also, I am worried that someone in
> > >>> the future will unknowingly change it to unsigns or to phys_addr_t. It
> > >>> is safer to have start explicitly set to 0 in case of wrap.
> > >>
> > >> memstart_addr is already a s64 for this exact reason.
> > >
> > > memstart_addr is basically an offset and it must be negative. For
> > > example, this would not work if it was not signed:
> > > #define vmemmap ((struct page *)VMEMMAP_START - (memstart_addr >> PAGE_SHIFT))
> > >
> > > However, on powerpc it is phys_addr_t type.
> > >
> > >>
> > >> Btw, the KASLR check is incorrect: memstart_addr could also be
> > >> negative when running the 52-bit VA kernel on hardware that is only
> > >> 48-bit VA capable.
> > >
> > > Good point!
> > >
> > > if (IS_ENABLED(CONFIG_ARM64_VA_BITS_52) && (vabits_actual != 52))
> > > memstart_addr -= _PAGE_OFFSET(48) - _PAGE_OFFSET(52);
> > >
> > > So, I will remove IS_ENABLED(CONFIG_RANDOMIZE_BASE) again.
> > >
> > > I am OK to change start_linear_pa, end_linear_pa to signed, but IMO
> > > what I have now is actually safer to make sure that does not break
> > > again in the future.
> > An explicit check for the flip over and providing two different start
> > addresses points would be required in order to use the new framework.
>
> I don't think so. We no longer randomize over the same range, but take
> the support PA range into account. (97d6786e0669d)
>
> This should ensure that __pa(_PAGE_OFFSET(vabits_actual)) never
> assumes a negative value. And to Pavel's point re 48/52 bit VAs: the
> fact that vabits_actual appears in this expression means that it
> already takes this into account, so you are correct that we don't have
> to care about that here.
>
> So even if memstart_addr could be negative, this expression should
> never produce a negative value. And with the patch above applied, it
> should never do so when running under KASLR either.
>
> So question to Pavel and Tyler: could you please check whether you
> have that patch, and whether it fixes the issue? It was introduced in
> v5.11, and hasn't been backported yet (it wasn't marked for -stable)

97d6786e0669d
arm64: mm: account for hotplug memory when randomizing the linear region

Does not address the problem that is described in this bug. It only
addresses the problem of adding extra PA space to the linear map which
is indeed needed (btw is it possible that hot plug is going to add
below memblock_start_of_DRAM(), because that is not currently
accounted) , but not the fact that a linear map can start from high
addresses because of randomization. I have verified that in QEMU, and
Tyler verified it on real hardware backporting it to 5.10, the problem
that this patch fixes is still there.

Pasha