Re: [PATCH v3 2/3] arm64: dts: imx: Add i.mx8mm nitrogen8mm basic dts support

From: Krzysztof Kozlowski
Date: Fri Jan 15 2021 - 12:18:59 EST

Next message: Elena Petrova: "[PATCH v3 0/9] UBSan Enablement for hyp/nVHE code"
Previous message: Alexander Potapenko: "Re: [PATCH v2 2/5] lib: add error_report_notify to collect debugging tools' reports"
In reply to: Adrien Grassein: "[PATCH v3 2/3] arm64: dts: imx: Add i.mx8mm nitrogen8mm basic dts support"
Next in thread: Adrien Grassein: "[PATCH v3 3/3] arm64: defconfig: Enable PF8x00 as builtin"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]

On Wed, Jan 13, 2021 at 06:38:54PM +0100, Adrien Grassein wrote:
> Tested with a basic Build Root configuration booting from sdcard.
>
> Signed-off-by: Adrien Grassein <adrien.grassein@xxxxxxxxx>
> ---
> arch/arm64/boot/dts/freescale/Makefile | 1 +
> .../dts/freescale/imx8mm-nitrogen8mm_rev2.dts | 417 ++++++++++++++++++
> 2 files changed, 418 insertions(+)
> create mode 100644 arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
>
> diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
> index 901d80086b47..b2eb7a5e4db3 100644
> --- a/arch/arm64/boot/dts/freescale/Makefile
> +++ b/arch/arm64/boot/dts/freescale/Makefile
> @@ -45,6 +45,7 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-devkit.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-librem5-r3.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-nitrogen.dtb
> +dtb-$(CONFIG_ARCH_MXC) += imx8mm-nitrogen8mm_rev2.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-phanbell.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-pico-pi.dtb
> dtb-$(CONFIG_ARCH_MXC) += imx8mq-thor96.dtb
> diff --git a/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> new file mode 100644
> index 000000000000..a83fa8d05e81
> --- /dev/null
> +++ b/arch/arm64/boot/dts/freescale/imx8mm-nitrogen8mm_rev2.dts
> @@ -0,0 +1,417 @@
> +// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
> +/*
> + * Device Tree file for Boundary Devices i.MX8MMini Nitrogen8MM Rev2 board.
> + * Adrien Grassein <adrien.grassein@xxxxxxxxxxxxx>
> + */
> +/dts-v1/;
> +#include "imx8mm.dtsi"
> +
> +/ {
> + model = "Boundary Devices i.MX8MMini Nitrogen8MM Rev2";
> + compatible = "boundary,imx8mm-nitrogen8mm", "fsl,imx8mm";
> +};
> +
> +&A53_0 {
> + cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_1 {
> + cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_2 {
> + cpu-supply = <&reg_sw3>;
> +};
> +
> +&A53_3 {
> + cpu-supply = <&reg_sw3>;
> +};
> +
> +&fec1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_fec1>;
> +
> + phy-mode = "rgmii-id";
> + phy-handle = <&ethphy0>;
> + fsl,magic-packet;
> + status = "okay";
> +
> + mdio {
> + #address-cells = <1>;
> + #size-cells = <0>;
> + ethphy0: ethernet-phy@4 {
> + compatible = "ethernet-phy-id004d.d072",
> + "ethernet-phy-ieee802.3-c22";
> + reg = <4>;
> + interrupts-extended = <&gpio3 16 IRQ_TYPE_LEVEL_LOW>;
> + };
> + };
> +};
> +
> +&i2c1 {
> + clock-frequency = <400000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c1>;
> + pinctrl-1 = <&pinctrl_i2c1_1>;
> + scl-gpios = <&gpio5 14 GPIO_OPEN_DRAIN>;
> + sda-gpios = <&gpio5 15 GPIO_OPEN_DRAIN>;
> + status = "okay";
> +
> + pmic@8 {
> + compatible = "nxp,pf8121a";
> + reg = <0x8>;
> + status = "okay";
> +
> + regulators {
> + reg_ldo1: ldo1 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <1500000>;

Thanks for the changes.

The usual convention is to order the fields from min to max, as it is
used in most of other bindings. So first goes min, then max.

Somehow the nxp,pf8x00-regulator.yaml example codes has less logical
order (also starting with always-on and boot-on) and people (last time I
think Jagan) tend to copy it... don't. Do like all other regulators and
DTSes. It makes life of reviewers and future contributors easier.

> + };
> +
> + reg_ldo2: ldo2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <1500000>;
> + };
> +
> + reg_ldo3: ldo3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <1500000>;
> + };
> +
> + reg_ldo4: ldo4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <5000000>;
> + regulator-min-microvolt = <1500000>;
> + };
> +
> + reg_buck1: buck1 {
> + nxp,ilim-ma = <4500>;
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_buck2: buck2 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_sw3: buck3 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_buck4: buck4 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_buck5: buck5 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_buck6: buck6 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <1800000>;
> + regulator-min-microvolt = <400000>;
> + };
> +
> + reg_buck7: buck7 {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <3300000>;
> + };
> +
> + reg_vsnvs: vsnvs {
> + regulator-always-on;
> + regulator-boot-on;
> + regulator-max-microvolt = <3300000>;
> + regulator-min-microvolt = <1800000>;
> + };
> + };
> + };
> +};
> +
> +&i2c3 {
> + clock-frequency = <100000>;
> + pinctrl-names = "default", "gpio";
> + pinctrl-0 = <&pinctrl_i2c3>;
> + pinctrl-1 = <&pinctrl_i2c3_1>;
> + scl-gpios = <&gpio5 18 GPIO_OPEN_DRAIN>;
> + sda-gpios = <&gpio5 19 GPIO_OPEN_DRAIN>;
> + status = "okay";
> +
> + i2cmux@70 {
> + compatible = "nxp,pca9540";
> + reg = <0x70>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> +
> + i2c3@0 {
> + reg = <0>;
> + #address-cells = <1>;
> + #size-cells = <0>;
> + rtc@68 {
> + compatible = "microcrystal,rv4162";
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_i2c3a_rv4162>;
> + reg = <0x68>;
> + interrupts-extended = <&gpio4 22 IRQ_TYPE_LEVEL_LOW>;
> + wakeup-source;
> + };
> + };
> + };
> +};
> +
> +/* console */
> +&uart2 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_uart2>;
> + assigned-clocks = <&clk IMX8MM_CLK_UART2>;
> + assigned-clock-parents = <&clk IMX8MM_CLK_24M>;
> + status = "okay";
> +};
> +
> +/* eMMC */
> +&usdhc1 {
> + bus-width = <8>;
> + sdhci-caps-mask = <0x80000000 0x0>;
> + non-removable;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc1>;
> + pinctrl-1 = <&pinctrl_usdhc1_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc1_200mhz>;
> + status = "okay";
> +};
> +
> +/* sdcard */
> +&usdhc2 {
> + bus-width = <4>;
> + cd-gpios = <&gpio2 12 GPIO_ACTIVE_LOW>;
> + pinctrl-names = "default", "state_100mhz", "state_200mhz";
> + pinctrl-0 = <&pinctrl_usdhc2>;
> + pinctrl-1 = <&pinctrl_usdhc2_100mhz>;
> + pinctrl-2 = <&pinctrl_usdhc2_200mhz>;
> + status = "okay";
> + vqmmc-supply = <&reg_ldo2>;
> +};
> +
> +&wdog1 {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_wdog>;
> + fsl,ext-reset-output;
> + status = "okay";
> +};
> +
> +&iomuxc {
> + pinctrl-names = "default";
> + pinctrl-0 = <&pinctrl_hog>;
> +
> + pinctrl_fec1: fec1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_ENET_MDC_ENET1_MDC 0x3
> + MX8MM_IOMUXC_ENET_MDIO_ENET1_MDIO 0x3
> + MX8MM_IOMUXC_ENET_TD3_ENET1_RGMII_TD3 0x1f
> + MX8MM_IOMUXC_ENET_TD2_ENET1_RGMII_TD2 0x1f
> + MX8MM_IOMUXC_ENET_TD1_ENET1_RGMII_TD1 0x1f
> + MX8MM_IOMUXC_ENET_TD0_ENET1_RGMII_TD0 0x1f
> + MX8MM_IOMUXC_ENET_RD3_ENET1_RGMII_RD3 0x91
> + MX8MM_IOMUXC_ENET_RD2_ENET1_RGMII_RD2 0x91
> + MX8MM_IOMUXC_ENET_RD1_ENET1_RGMII_RD1 0x91
> + MX8MM_IOMUXC_ENET_RD0_ENET1_RGMII_RD0 0x91
> + MX8MM_IOMUXC_ENET_TXC_ENET1_RGMII_TXC 0x1f
> + MX8MM_IOMUXC_ENET_RXC_ENET1_RGMII_RXC 0x91
> + MX8MM_IOMUXC_ENET_RX_CTL_ENET1_RGMII_RX_CTL 0x91
> + MX8MM_IOMUXC_ENET_TX_CTL_ENET1_RGMII_TX_CTL 0x1f
> + MX8MM_IOMUXC_NAND_READY_B_GPIO3_IO16 0x159
> + >;
> + };
> +
> + pinctrl_hog: hoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO03_GPIO1_IO3 0x09
> + MX8MM_IOMUXC_GPIO1_IO08_GPIO1_IO8 0x09
> + >;
> + };
> +
> + pinctrl_i2c1: i2c1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_I2C1_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_I2C1_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c1_1: i2c1-1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C1_SCL_GPIO5_IO14 0x400001c3
> + MX8MM_IOMUXC_I2C1_SDA_GPIO5_IO15 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3: i2c3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_I2C3_SCL 0x400001c3
> + MX8MM_IOMUXC_I2C3_SDA_I2C3_SDA 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3_1: i2c3-1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_I2C3_SCL_GPIO5_IO18 0x400001c3
> + MX8MM_IOMUXC_I2C3_SDA_GPIO5_IO19 0x400001c3
> + >;
> + };
> +
> + pinctrl_i2c3a_rv4162: i2c3a-rv4162grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SAI2_RXC_GPIO4_IO22 0x1c0
> + >;
> + };
> +
> + pinctrl_uart2: uart2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_UART2_RXD_UART2_DCE_RX 0x140
> + MX8MM_IOMUXC_UART2_TXD_UART2_DCE_TX 0x140
> + >;
> + };
> +
> + pinctrl_usdhc1: usdhc1grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x190
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d0
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d0
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d0
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d0
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d0
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d0
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d0
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d0
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d0
> + MX8MM_IOMUXC_SD1_RESET_B_GPIO2_IO10 0x141
> + >;
> + };
> +
> + pinctrl_usdhc1_100mhz: usdhc1-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x194
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d4
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d4
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d4
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d4
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d4
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d4
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d4
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d4
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc1_200mhz: usdhc1-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD1_CLK_USDHC1_CLK 0x196
> + MX8MM_IOMUXC_SD1_CMD_USDHC1_CMD 0x1d6
> + MX8MM_IOMUXC_SD1_DATA0_USDHC1_DATA0 0x1d6
> + MX8MM_IOMUXC_SD1_DATA1_USDHC1_DATA1 0x1d6
> + MX8MM_IOMUXC_SD1_DATA2_USDHC1_DATA2 0x1d6
> + MX8MM_IOMUXC_SD1_DATA3_USDHC1_DATA3 0x1d6
> + MX8MM_IOMUXC_SD1_DATA4_USDHC1_DATA4 0x1d6
> + MX8MM_IOMUXC_SD1_DATA5_USDHC1_DATA5 0x1d6
> + MX8MM_IOMUXC_SD1_DATA6_USDHC1_DATA6 0x1d6
> + MX8MM_IOMUXC_SD1_DATA7_USDHC1_DATA7 0x1d6
> + >;
> + };
> +
> + pinctrl_usdhc2: usdhc2grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x190
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d0
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d0
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d0
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d0
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d0
> + MX8MM_IOMUXC_SD2_CD_B_GPIO2_IO12 0x1c4
> + >;
> + };
> +
> + pinctrl_usdhc2_100mhz: usdhc2-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x194
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d4
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d4
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d4
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d4
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc2_200mhz: usdhc2-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_SD2_CLK_USDHC2_CLK 0x196
> + MX8MM_IOMUXC_SD2_CMD_USDHC2_CMD 0x1d6
> + MX8MM_IOMUXC_SD2_DATA0_USDHC2_DATA0 0x1d6
> + MX8MM_IOMUXC_SD2_DATA1_USDHC2_DATA1 0x1d6
> + MX8MM_IOMUXC_SD2_DATA2_USDHC2_DATA2 0x1d6
> + MX8MM_IOMUXC_SD2_DATA3_USDHC2_DATA3 0x1d6
> + >;
> + };
> +
> + pinctrl_usdhc3: usdhc3grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x190
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d0
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d0
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d0
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d0
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d0
> + MX8MM_IOMUXC_GPIO1_IO00_ANAMIX_REF_CLK_32K 0x03
> + >;
> + };
> +
> + pinctrl_usdhc3_100mhz: usdhc3-100mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x194
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d4
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d4
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d4
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d4
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d4
> + >;
> + };
> +
> + pinctrl_usdhc3_200mhz: usdhc3-200mhz-grp {
> + fsl,pins = <
> + MX8MM_IOMUXC_NAND_WE_B_USDHC3_CLK 0x196
> + MX8MM_IOMUXC_NAND_WP_B_USDHC3_CMD 0x1d6
> + MX8MM_IOMUXC_NAND_DATA04_USDHC3_DATA0 0x1d6
> + MX8MM_IOMUXC_NAND_DATA05_USDHC3_DATA1 0x1d6
> + MX8MM_IOMUXC_NAND_DATA06_USDHC3_DATA2 0x1d6
> + MX8MM_IOMUXC_NAND_DATA07_USDHC3_DATA3 0x1d6
> + >;
> + };
> +
> + pinctrl_wdog: wdoggrp {
> + fsl,pins = <
> + MX8MM_IOMUXC_GPIO1_IO02_WDOG1_WDOG_B 0x140
> + >;
> + };
> +

Unneeded blank line.

Best regards,
Krzysztof

Next message: Elena Petrova: "[PATCH v3 0/9] UBSan Enablement for hyp/nVHE code"
Previous message: Alexander Potapenko: "Re: [PATCH v2 2/5] lib: add error_report_notify to collect debugging tools' reports"
In reply to: Adrien Grassein: "[PATCH v3 2/3] arm64: dts: imx: Add i.mx8mm nitrogen8mm basic dts support"
Next in thread: Adrien Grassein: "[PATCH v3 3/3] arm64: defconfig: Enable PF8x00 as builtin"
Messages sorted by: [ date ] [ thread ] [ subject ] [ author ]