Re: [PATCH v1 1/1] hsu_dma_pci: disable spurious interrupt

[Andy Shevchenko]

On Wed, Jan 13, 2021 at 5:23 AM Ferry Toth <ftoth@xxxxxxxxxxxxxx> wrote:
>
> On Intel Tangier B0 and Anniedale the interrupt line, disregarding
> to have different numbers, is shared between HSU DMA and UART IPs.
> Thus on such SoCs we are expecting that IRQ handler is called in
> UART driver only. hsu_pci_irq was handling the spurious interrupt

hsu_pci_irq()

> from HSU DMA by returning immediately. This wastes CPU time and
> since HSU DMA and HSU UART interrupt occur simultaneously they race
> to be handled causing delay to the HSU UART interrupt handling.
> Fix this by disabling the interrupt entirely.

Title should be "dmaengine: hsu: ..."

After addressing above
Reviewed-by: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>


> Fixes: 4831e0d9054c ("serial: 8250_mid: handle interrupt correctly in DMA case")
> Signed-off-by: Ferry Toth <ftoth@xxxxxxxxxxxxxx>
> ---
>  drivers/dma/hsu/pci.c | 21 +++++++++++----------
>  1 file changed, 11 insertions(+), 10 deletions(-)
>
> diff --git a/drivers/dma/hsu/pci.c b/drivers/dma/hsu/pci.c
> index 07cc7320a614..9045a6f7f589 100644
> --- a/drivers/dma/hsu/pci.c
> +++ b/drivers/dma/hsu/pci.c
> @@ -26,22 +26,12 @@
>  static irqreturn_t hsu_pci_irq(int irq, void *dev)
>  {
>         struct hsu_dma_chip *chip = dev;
> -       struct pci_dev *pdev = to_pci_dev(chip->dev);
>         u32 dmaisr;
>         u32 status;
>         unsigned short i;
>         int ret = 0;
>         int err;
>
> -       /*
> -        * On Intel Tangier B0 and Anniedale the interrupt line, disregarding
> -        * to have different numbers, is shared between HSU DMA and UART IPs.
> -        * Thus on such SoCs we are expecting that IRQ handler is called in
> -        * UART driver only.
> -        */
> -       if (pdev->device == PCI_DEVICE_ID_INTEL_MRFLD_HSU_DMA)
> -               return IRQ_HANDLED;
> -
>         dmaisr = readl(chip->regs + HSU_PCI_DMAISR);
>         for (i = 0; i < chip->hsu->nr_channels; i++) {
>                 if (dmaisr & 0x1) {
> @@ -105,6 +95,17 @@ static int hsu_pci_probe(struct pci_dev *pdev, const struct pci_device_id *id)
>         if (ret)
>                 goto err_register_irq;
>
> +       /*
> +        * On Intel Tangier B0 and Anniedale the interrupt line, disregarding
> +        * to have different numbers, is shared between HSU DMA and UART IPs.
> +        * Thus on such SoCs we are expecting that IRQ handler is called in
> +        * UART driver only. Instead of handling the spurious interrupt
> +        * from HSU DMA here and waste CPU time and delay HSU UART interrupt
> +        * handling, disable the interrupt entirely.
> +        */
> +       if (pdev->device == PCI_DEVICE_ID_INTEL_MRFLD_HSU_DMA)
> +               disable_irq_nosync(chip->irq);
> +
>         pci_set_drvdata(pdev, chip);
>
>         return 0;
> --
> 2.27.0
>


-- 
With Best Regards,
Andy Shevchenko