Re: [PATCH v4 1/1] PCI/ERR: don't clobber status after reset_link()

[Bjorn Helgaas]

[+cc Keith]

On Thu, Dec 10, 2020 at 04:41:42PM -0600, Bjorn Helgaas wrote:
> On Mon, Nov 02, 2020 at 03:09:51PM +0000, Hedi Berriche wrote:
> > Commit 6d2c89441571 ("PCI/ERR: Update error status after reset_link()")
> > broke pcie_do_recovery(): updating status after reset_link() has the ill
> > side effect of causing recovery to fail if the error status is
> > PCI_ERS_RESULT_CAN_RECOVER or PCI_ERS_RESULT_NEED_RESET as the following
> > code will *never* run in the case of a successful reset_link()
> > 
> >    177         if (status == PCI_ERS_RESULT_CAN_RECOVER) {
> >    ...
> >    181         }
> > 
> >    183         if (status == PCI_ERS_RESULT_NEED_RESET) {
> >    ...
> >    192         }
> 
> The line numbers are basically useless because they depend on some
> particular version of the file.
> 
> > For instance in the case of PCI_ERS_RESULT_NEED_RESET we end up not
> > calling ->slot_reset() (because we skip report_slot_reset()) thus
> > breaking driver (re)initialisation.
> > 
> > Don't clobber status with the return value of reset_link(); set status
> > to PCI_ERS_RESULT_RECOVERED, in case of successful link reset, if and
> > only if the initial value of error status is PCI_ERS_RESULT_DISCONNECT
> > or PCI_ERS_RESULT_NO_AER_DRIVER.
> >
> > Fixes: 6d2c89441571 ("PCI/ERR: Update error status after reset_link()")
> > Signed-off-by: Hedi Berriche <hedi.berriche@xxxxxxx>
> > 
> > Reviewed-by: Sinan Kaya <okaya@xxxxxxxxxx>
> > Cc: Russ Anderson <rja@xxxxxxx>
> > Cc: Kuppuswamy Sathyanarayanan <sathyanarayanan.kuppuswamy@xxxxxxxxxxxxxxx>
> > Cc: Bjorn Helgaas <bhelgaas@xxxxxxxxxx>
> > Cc: Ashok Raj <ashok.raj@xxxxxxxxx>
> > Cc: Joerg Roedel <jroedel@xxxxxxxx>
> > 
> > Cc: stable@xxxxxxxxxx # v5.7+
> > ---
> >  drivers/pci/pcie/err.c | 7 +++++--
> >  1 file changed, 5 insertions(+), 2 deletions(-)
> > 
> > diff --git a/drivers/pci/pcie/err.c b/drivers/pci/pcie/err.c
> > index c543f419d8f9..2730826cfd8a 100644
> > --- a/drivers/pci/pcie/err.c
> > +++ b/drivers/pci/pcie/err.c
> > @@ -165,10 +165,13 @@ pci_ers_result_t pcie_do_recovery(struct pci_dev *dev,
> >  	pci_dbg(dev, "broadcast error_detected message\n");
> >  	if (state == pci_channel_io_frozen) {
> >  		pci_walk_bus(bus, report_frozen_detected, &status);
> > -		status = reset_link(dev);
> > -		if (status != PCI_ERS_RESULT_RECOVERED) {
> > +		if (reset_link(dev) != PCI_ERS_RESULT_RECOVERED) {
> >  			pci_warn(dev, "link reset failed\n");
> >  			goto failed;
> > +		} else {
> > +			if (status == PCI_ERS_RESULT_DISCONNECT ||
> > +			    status == PCI_ERS_RESULT_NO_AER_DRIVER)
> > +				status = PCI_ERS_RESULT_RECOVERED;
> 
> This code (even before your patch) doesn't match
> Documentation/PCI/pci-error-recovery.rst very well.  The code handles
> pci_channel_io_frozen specially, but I don't think this is mentioned
> in the doc.
> 
> The doc says we call ->error_detected() for all affected drivers.
> Then we're supposed to do a slot reset if any driver returned
> NEED_RESET.  But in fact, we always do a reset for the
> pci_channel_io_frozen case and never do one otherwise, regardless of
> what ->error_detected() returned.
> 
> The doc says DISCONNECT means "Driver ... doesn't want to recover at
> all." Many drivers can return either NEED_RESET or DISCONNECT, and I
> assume they expect them to be handled differently.  But I'm not sure
> what DISCONNECT really means.  Do we reset the device?  Do we not
> attempt recovery at all?
> 
> After your patch, if the reset_link() succeeded, we convert DISCONNECT
> and NO_AER_DRIVER to RECOVERED.  IIUC, that means we do exactly the
> same thing if the consensus of the ->error_detected() functions was
> RECOVERED, DISCONNECT, or NO_AER_DRIVER: we call reset_link() and
> continue with "status = PCI_ERS_RESULT_RECOVERED".
> 
> (I'd reverse the sense of the "if (reset_link())" to make this easier
> to read)

Can we push this forward now?  There are several pending patches in
this area from Keith and Sathyanarayanan; I haven't gotten to them
yet, so not sure whether they help address any of this.

> >  		}
> >  	} else {
> >  		pci_walk_bus(bus, report_normal_detected, &status);
> > -- 
> > 2.28.0
> >