Re: [PATCH v4 01/11] dt-bindings: usb: convert usb-device.txt to YAML schema

[Chunfeng Yun]

On Mon, 2020-12-21 at 12:09 -0700, Rob Herring wrote:
> On Wed, Dec 16, 2020 at 05:30:02PM +0800, Chunfeng Yun wrote:
> > Convert usb-device.txt to YAML schema usb-device.yaml
> > 
> > Signed-off-by: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
> > ---
> > v4: no changes, update dependent series:
> >     https://patchwork.kernel.org/project/linux-usb/list/?series=399561
> >     [v6,00/19] dt-bindings: usb: Add generic USB HCD, xHCI, DWC USB3 DT schema
[...]
> > diff --git a/Documentation/devicetree/bindings/usb/usb-device.yaml b/Documentation/devicetree/bindings/usb/usb-device.yaml
> > new file mode 100644
> > index 000000000000..f31d8a85d3e6
> > --- /dev/null
> > +++ b/Documentation/devicetree/bindings/usb/usb-device.yaml
> > @@ -0,0 +1,125 @@
> > +# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
> > +%YAML 1.2
> > +---
> > +$id: http://devicetree.org/schemas/usb/usb-device.yaml#
> > +$schema: http://devicetree.org/meta-schemas/core.yaml#
> > +
> > +title: The device tree bindings for the Generic USB Device
> > +
> > +maintainers:
> > +  - Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
> > +
> > +description: |
> > +  Usually, we only use device tree for hard wired USB device.
> > +  The reference binding doc is from:
> > +  http://www.devicetree.org/open-firmware/bindings/usb/usb-1_0.ps
> > +
> > +  Four types of device-tree nodes are defined: "host-controller nodes"
> > +  representing USB host controllers, "device nodes" representing USB devices,
> > +  "interface nodes" representing USB interfaces and "combined nodes"
> > +  representing simple USB devices.
> > +
> > +  A combined node shall be used instead of a device node and an interface node
> > +  for devices of class 0 or 9 (hub) with a single configuration and a single
> > +  interface.
> > +
> > +  A "hub node" is a combined node or an interface node that represents a USB
> > +  hub.
> > +
> > +properties:
> > +  compatible:
> > +    pattern: "^usb[0-9a-f]+,[0-9a-f]+$"
> 
> You can refine the length allowed a bit: [0-9a-f]{1,4}
> 
> Same applies elsewhere.
Ok
> 
> > +    description: Device nodes or combined nodes.
> > +      "usbVID,PID", where VID is the vendor id and PID the product id.
> > +      The textual representation of VID and PID shall be in lower case
> > +      hexadecimal with leading zeroes suppressed. The other compatible
> > +      strings from the above standard binding could also be used,
> > +      but a device adhering to this binding may leave out all except
> > +      for "usbVID,PID".
> > +
[...]
> > diff --git a/Documentation/devicetree/bindings/usb/usb-hcd.yaml b/Documentation/devicetree/bindings/usb/usb-hcd.yaml
> > index 9881ac10380d..5d0c6b5500d6 100755
> > --- a/Documentation/devicetree/bindings/usb/usb-hcd.yaml
> > +++ b/Documentation/devicetree/bindings/usb/usb-hcd.yaml
> > @@ -23,6 +23,32 @@ properties:
> >        targeted hosts (non-PC hosts).
> >      type: boolean
> >  
> > +  "#address-cells":
> > +    const: 1
> > +
> > +  "#size-cells":
> > +    const: 0
> > +
> > +patternProperties:
> > +  "@[0-9a-f]+$":
> > +    type: object
> > +    description: The hard wired USB devices
> > +
> > +    properties:
> > +      compatible:
> > +        pattern: "^usb[0-9a-f]+,[0-9a-f]+$"
> > +        $ref: /usb/usb-device.yaml
> 
> This is wrong. It should be up a level.
Ok
>  And no need to define 
> 'compatible' or 'reg' here because those are defined within 
> usb-device.yaml.
will drop it
> 
> > +        description: the string is 'usbVID,PID', where VID is the vendor id
> > +          and PID is the product id
> > +
> > +      reg:
> > +        $ref: /usb/usb-device.yaml
> > +        maxItems: 1
> > +
> > +    required:
> > +      - compatible
> > +      - reg
> > +
> >  additionalProperties: true
> >  
> >  examples:
> > @@ -30,4 +56,11 @@ examples:
> >      usb {
> >          phys = <&usb2_phy1>, <&usb3_phy1>;
> >          phy-names = "usb";
> > +        #address-cells = <1>;
> > +        #size-cells = <0>;
> > +
> > +        hub@1 {
> > +            compatible = "usb5e3,610";
> > +            reg = <1>;
> > +        };
> >      };
> > -- 
> > 2.18.0
> >