Re: [PATCH] MIPS: Ingenic: Disable HPTLB for D0 XBurst CPUs too

[Paul Cercueil]

Hi Zhou,

Le lun. 14 déc. 2020 à 3:12, Zhou Yanjie <zhouyanjie@xxxxxxxxxxxxxx> 
a écrit :
> Hi Paul,
>
> On 2020/12/12 上午8:03, Paul Cercueil wrote:
> > The JZ4760 has the HPTLB as well, but has a XBurst CPU with a D0 
> > CPUID.
> >
> > Disable the HPTLB for all XBurst CPUs with a D0 CPUID. In the case 
> > where
> > there is no HPTLB (e.g. for older SoCs), this won't have any side
> > effect.
> >
> > Fixes: b02efeb05699 ("MIPS: Ingenic: Disable abandoned HPTLB 
> > function.")
> > Cc: <stable@xxxxxxxxxxxxxxx> # 5.4
> > Signed-off-by: Paul Cercueil <paul@xxxxxxxxxxxxxxx>
> > ---
> >   arch/mips/kernel/cpu-probe.c | 15 ++++++++-------
> >   1 file changed, 8 insertions(+), 7 deletions(-)
> >
> > diff --git a/arch/mips/kernel/cpu-probe.c 
> > b/arch/mips/kernel/cpu-probe.c
> > index e6853697a056..31cb9199197c 100644
> > --- a/arch/mips/kernel/cpu-probe.c
> > +++ b/arch/mips/kernel/cpu-probe.c
> > @@ -1830,16 +1830,17 @@ static inline void cpu_probe_ingenic(struct 
> > cpuinfo_mips *c, unsigned int cpu)
> >   		 */
> >   		case PRID_COMP_INGENIC_D0:
> >   			c->isa_level &= ~MIPS_CPU_ISA_M32R2;
> > -			break;
> > +			fallthrough;
> >     		/*
> >   		 * The config0 register in the XBurst CPUs with a processor ID of
> > -		 * PRID_COMP_INGENIC_D1 has an abandoned huge page tlb mode, this
> > -		 * mode is not compatible with the MIPS standard, it will cause
> > -		 * tlbmiss and into an infinite loop (line 21 in the tlb-funcs.S)
> > -		 * when starting the init process. After chip reset, the default
> > -		 * is HPTLB mode, Write 0xa9000000 to cp0 register 5 sel 4 to
>
>
> I just noticed that I mistakenly wrote a capital 'W' in the original 
> version.
>
> with that fixed:
>
> Reviewed-by: 周琰杰 (Zhou Yanjie) <zhouyanjie@xxxxxxxxxxxxxx>

Sure, thanks.

If both D0 and D1 CPUs need the fix then I probably should move it 
outside the switch, that would make the code a bit cleaner. I'll V2.

> BTW: Are you planning to add support for JZ4760 recently? I am 
> currently writing the CGU driver for JZ4775 and X2000. If you plan to 
> add support for JZ4760, I can also write the CGU driver for JZ4760 by 
> the way.

Yes, we're working on it, all the core drivers are working (CGU, 
pinctrl, timers, display, USB), it boots to userspace and allows to 
telnet. The actual diff is very small, most of the changes were the 
addition of the ingenic,jz4760-* compatible strings.

Cheers,
-Paul

> > -		 * switch back to VTLB mode to prevent getting stuck.
> > +		 * PRID_COMP_INGENIC_D0 or PRID_COMP_INGENIC_D1 has an abandoned
> > +		 * huge page tlb mode, this mode is not compatible with the MIPS
> > +		 * standard, it will cause tlbmiss and into an infinite loop
> > +		 * (line 21 in the tlb-funcs.S) when starting the init process.
> > +		 * After chip reset, the default is HPTLB mode, Write 0xa9000000
> > +		 * to cp0 register 5 sel 4 to switch back to VTLB mode to prevent
> > +		 * getting stuck.
> >   		 */
> >   		case PRID_COMP_INGENIC_D1:
> >   			write_c0_page_ctrl(XBURST_PAGECTRL_HPTLB_DIS);