[PATCH 10/14] ARM: dts: sun8i: v3s: Add MIPI D-PHY and MIPI CSI-2 interface nodes

[Paul Kocialkowski]

MIPI CSI-2 is supported on the V3s with an A31 controller, which seems
to be used on all Allwinner chips supporting it, except for the A83T.
The controller is connected to CSI0 through fwnode endpoints.
The mipi_csi2_in port node is provided to connect MIPI CSI-2 sensors.

The D-PHY part is the same that already drives DSI, but used in Rx mode.

Signed-off-by: Paul Kocialkowski <paul.kocialkowski@xxxxxxxxxxx>
---
 arch/arm/boot/dts/sun8i-v3s.dtsi | 50 ++++++++++++++++++++++++++++++++
 1 file changed, 50 insertions(+)

diff --git a/arch/arm/boot/dts/sun8i-v3s.dtsi b/arch/arm/boot/dts/sun8i-v3s.dtsi
index 07722bc5df11..6e10c10ab283 100644
--- a/arch/arm/boot/dts/sun8i-v3s.dtsi
+++ b/arch/arm/boot/dts/sun8i-v3s.dtsi
@@ -534,6 +534,13 @@ csi0: camera@1cb0000 {
 			clock-names = "bus", "mod", "ram";
 			resets = <&ccu RST_BUS_CSI>;
 			status = "disabled";
+
+			csi0_in: port {
+				csi0_in_mipi_csi2: endpoint {
+					bus-type = <4>; /* CSI2_DPHY */
+					remote-endpoint = <&mipi_csi2_out_csi0>;
+				};
+			};
 		};
 
 		csi1: camera@1cb4000 {
@@ -558,5 +565,48 @@ gic: interrupt-controller@1c81000 {
 			#interrupt-cells = <3>;
 			interrupts = <GIC_PPI 9 (GIC_CPU_MASK_SIMPLE(4) | IRQ_TYPE_LEVEL_HIGH)>;
 		};
+
+		mipi_csi2: mipi-csi2@1cb1000 {
+			compatible = "allwinner,sun8i-v3s-mipi-csi2",
+				     "allwinner,sun6i-a31-mipi-csi2";
+			reg = <0x01cb1000 0x1000>;
+			interrupts = <GIC_SPI 90 IRQ_TYPE_LEVEL_HIGH>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_CSI1_SCLK>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+
+			phys = <&dphy>;
+			phy-names = "dphy";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				mipi_csi2_in: port@0 {
+					reg = <0>;
+				};
+
+				mipi_csi2_out: port@1 {
+					reg = <1>;
+
+					mipi_csi2_out_csi0: endpoint {
+						remote-endpoint = <&csi0_in_mipi_csi2>;
+					};
+				};
+			};
+		};
+
+		dphy: d-phy@1cb2000 {
+			compatible = "allwinner,sun6i-a31-mipi-dphy";
+			reg = <0x01cb2000 0x1000>;
+			clocks = <&ccu CLK_BUS_CSI>,
+				 <&ccu CLK_MIPI_CSI>;
+			clock-names = "bus", "mod";
+			resets = <&ccu RST_BUS_CSI>;
+			status = "disabled";
+			#phy-cells = <0>;
+		};
 	};
 };
-- 
2.28.0