Re: [PATCH v1 4/6] dt-bindings: mfd: ene-kb3930: Add compatibles for KB930 and Acer A500

[Rob Herring]

On Mon, Aug 24, 2020 at 01:09:22PM +0300, Dmitry Osipenko wrote:
> 24.08.2020 00:16, Lubomir Rintel пишет:
> > Hello,
> > 
> > On Sun, Aug 23, 2020 at 10:31:36PM +0300, Dmitry Osipenko wrote:
> >> 23.08.2020 21:20, Lubomir Rintel пишет:
> >>> On Sun, Aug 23, 2020 at 05:08:44PM +0300, Dmitry Osipenko wrote:
> >>>> The ENE KB930 hardware is compatible with KB3930.
> >>>>
> >>>> Acer A500 Iconia Tab is Android tablet device, it has KB930 controller
> >>>> that is running firmware specifically customized for the needs of the
> >>>> Acer A500 hardware. This means that firmware interface isn't re-usable
> >>>> by other non-Acer devices. Some akin models of Acer tablets should be
> >>>> able to re-use the FW interface of A500 model, like A200 for example.
> >>>>
> >>>> This patch adds the new compatibles to the binding.
> >>>
> >>> I've responded to patch 5/6 with what should've been said here [1].
> >>> Sorry for the confusion.
> >>>
> >>> In any case please consider adding a new binding file instead of
> >>> modifying the kb3930 binding doc. It would also remove a dependency on
> >>> my patch set which should have slipped out of maintainers' radar.
> >>>
> >>> [1] https://lore.kernel.org/lkml/20200823180041.GB209852@demiurge.local/
> >>
> >> Hello, Lubomir! I was doing some research about the differences of
> >> KB3930 and KB930 before created this patch and my understanding is that
> >> the controllers are mostly identical. I've seen posts from people who
> >> replaced KB3930 with KB930 (and vice versa) on various notebooks and it
> >> worked, although not always.
> >>
> >> It's a very common practice to re-use binding in a case of a sibling
> >> hardware. Do you know what are the exact differences between KB3930 and
> >> KB930 which could justify having separate bindings?
> >>
> >> The firmware implementation varies a lot from device to device,
> > 
> > It sometimes does. The ENE's downstream driver suggests there are parts
> > that run more-or-less stock firmware that are comatible with each other.
> > That is why I grabbed the generic kb3930 name.
> > 
> >> and
> >> thus, each device needs to have its own driver in order to talk to the
> >> firmware, but hardware description (i.e. DT binding) should be common
> >> for all devices.
> > 
> > Note the DT is not the hardware description. It's the description of how
> > the hardware presents itself, from the software's perspective. As far as
> > that is concerned, the devices don't seem to have anything in common at
> > all (other than the bus address). The fact that you need an entirely
> > different driver implies this.
> > 
> > This would be the case even if the A500 EC was based directly on a KB3930.
> > 
> > A good reason to keep bindings for different yet somewhat similar devices in
> > a single document is to avoid duplication. Yet here there's very little to
> > share here. If you've done your bindings correctly, you'd need to
> > conditionalize the monitored-battery and power-supplies properties for
> > acer,a500-iconia-ec, complicating the binding too much. It makes more
> > sense to just add a new document.
> 
> Alright, I don't mind to separate the bindings. Although, before doing
> that, I'd want to get opinion from the device-tree experts, i.e. from
> Rob Herring :)
> 
> Rob, will it be fine to have separate bindings for each firmware version
> of the ENE controller given that firmware is individual for every device
> and given that FW has no compatibility with other devices?

Seems like separate bindings makes sense here.

Rob