Re: [PATCH v1] usb: typec: tcpm: Fix TDA 2.2.1.1 and TDA 2.2.1.2 failures

From: Badhri Jagan Sridharan
Date: Tue Aug 11 2020 - 22:04:16 EST


On Tue, Aug 11, 2020 at 6:44 PM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
>
> On 8/11/20 6:08 PM, Badhri Jagan Sridharan wrote:
> > Yes I did ! https://lkml.org/lkml/2020/8/11/788 !
> >
> > For me gmail is grouping V1 and V2 patches in the same thread so
> > thought you saw the v2 patch :P
> >
>
> You copied me on v1, but not on v2. I am not on any of the mailing lists
> you sent v2 to, so I did not see it.
>
> Guenter

My bad ! Apologies Guenter ! Screwed up while performing the git
send-email command.
Will make sure that I double check next time.

Thanks,
Badhri

>
> > Thanks,
> > Badhri
> >
> > On Tue, Aug 11, 2020 at 5:36 PM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
> >>
> >> On 8/11/20 4:21 PM, Badhri Jagan Sridharan wrote:
> >>> Thanks Guenter ! However I don't see a reviewed-by tag :)
> >>>
> >>
> >> Confused. Did you send a v2 with the changes we discussed ?
> >> I didn't see that.
> >>
> >> Thanks,
> >> Guenter
> >>
> >>> On Tue, Aug 11, 2020 at 1:18 PM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
> >>>>
> >>>> On 8/11/20 12:39 PM, Badhri Jagan Sridharan wrote:
> >>>>> On Tue, Aug 11, 2020 at 11:45 AM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
> >>>>>>
> >>>>>> On Tue, Aug 11, 2020 at 11:24:07AM -0700, Badhri Jagan Sridharan wrote:
> >>>>>>> On Mon, Aug 10, 2020 at 6:51 PM Guenter Roeck <linux@xxxxxxxxxxxx> wrote:
> >>>>>>>>
> >>>>>>>> On 8/10/20 6:11 PM, Badhri Jagan Sridharan wrote:
> >>>>>>>>> >From the spec:
> >>>>>>>>> "7.1.5 Response to Hard Resets
> >>>>>>>>> Hard Reset Signaling indicates a communication failure has occurred and
> >>>>>>>>> the Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin
> >>>>>>>>> and Shall drive VBUS to vSafe0V as shown in Figure 7-9. The USB connection
> >>>>>>>>> May reset during a Hard Reset since the VBUS voltage will be less than
> >>>>>>>>> vSafe5V for an extended period of time. After establishing the vSafe0V
> >>>>>>>>> voltage condition on VBUS, the Source Shall wait tSrcRecover before
> >>>>>>>>> re-applying VCONN and restoring VBUS to vSafe5V. A Source Shall conform
> >>>>>>>>> to the VCONN timing as specified in [USB Type-C 1.3]."
> >>>>>>>>>
> >>>>>>>>> Signed-off-by: Badhri Jagan Sridharan <badhri@xxxxxxxxxx>
> >>>>>>>>> ---
> >>>>>>>>> drivers/usb/typec/tcpm/tcpm.c | 16 +++++++++++++---
> >>>>>>>>> 1 file changed, 13 insertions(+), 3 deletions(-)
> >>>>>>>>>
> >>>>>>>>> diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
> >>>>>>>>> index 3ef37202ee37..e41c4e5d3c71 100644
> >>>>>>>>> --- a/drivers/usb/typec/tcpm/tcpm.c
> >>>>>>>>> +++ b/drivers/usb/typec/tcpm/tcpm.c
> >>>>>>>>> @@ -3372,13 +3372,19 @@ static void run_state_machine(struct tcpm_port *port)
> >>>>>>>>> tcpm_set_state(port, SNK_HARD_RESET_SINK_OFF, 0);
> >>>>>>>>> break;
> >>>>>>>>> case SRC_HARD_RESET_VBUS_OFF:
> >>>>>>>>> - tcpm_set_vconn(port, true);
> >>>>>>>>> + /*
> >>>>>>>>> + * 7.1.5 Response to Hard Resets
> >>>>>>>>> + * Hard Reset Signaling indicates a communication failure has occurred and the
> >>>>>>>>> + * Source Shall stop driving VCONN, Shall remove Rp from the VCONN pin and Shall
> >>>>>>>>> + * drive VBUS to vSafe0V as shown in Figure 7-9.
> >>>>>>>>> + */
> >>>>>>>>> + tcpm_set_vconn(port, false);
> >>>>>>>>> tcpm_set_vbus(port, false);
> >>>>>>>>> tcpm_set_roles(port, port->self_powered, TYPEC_SOURCE,
> >>>>>>>>> tcpm_data_role_for_source(port));
> >>>>>>>>> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> >>>>>>>>
> >>>>>>>> I am a bit concerned about this. If I understand correctly, it means that
> >>>>>>>> we won't turn VBUS back on unless a SRC_HARD_RESET_VBUS_OFF PD event is received.
> >>>>>>>> Is that correct ? What happens if that event is never received ?
> >>>>>>>>
> >>>>>>>> Thanks,
> >>>>>>>> Guenter
> >>>>>>>
> >>>>>>> The term PD event is a little ambiguous to me. Trying to summarize the workflow.
> >>>>>>> Lower level tcpc driver would have to call tcpm_vbus_change which
> >>>>>>> would in-turn trigger TCPM_VBUS_EVENT
> >>>>>>> and queries port->tcpc->get_vbus to get the vbus status. It is not
> >>>>>>> really a PD protocol driven event hence the
> >>>>>>> confusion.
> >>>>>>>
> >>>>>>> "What happens if that event is never received ?"
> >>>>>>> Yeah TCPM would be in SRC_HARD_RESET_VBUS_OFF till the tcpc calls the
> >>>>>>> tcpm_vbus_change.
> >>>>>>> Do you suspect that existing tcpc would not have the capability to
> >>>>>>> monitor vbus status while sourcing and call tcpm_vbus_change?
> >>>>>>>
> >>>>>> That, or the driver might be buggy, or the hardware does't signal a status
> >>>>>> update, or the update gets lost. I think we should have some backup,
> >>>>>> to trigger if the event is not received in a reasonable amout of time.
> >>>>>> I don't know if the specification has some kind of maximum limit. If
> >>>>>> not, we should still have something
> >>>>>>
> >>>>>> Thanks,
> >>>>>> Guenter
> >>>>>
> >>>>> Got it ! The specification actually has a bound for vbus off.
> >>>>> tSafe0V - Time to reach vSafe0V max - 650ms. (PD_T_SAFE_0V).
> >>>>> So I will bound it to that.
> >>>>>
> >>>>
> >>>> Excellent. Thanks a lot for looking into this!
> >>>>
> >>>> Guenter
> >>>>
> >>>>> >From Table 7-12 Sequence Description for a Source Initiated Hard Reset:
> >>>>> 4.Policy Engine waits tPSHardReset after sending Hard Reset Signaling
> >>>>> and then tells the Device Policy Manager to instruct the power supply
> >>>>> to perform a Hard Reset. The transition to vSafe0V Shall occur within
> >>>>> tSafe0V (t2).
> >>>>> 5 After tSrcRecover the Source applies power to VBUS in an attempt to
> >>>>> re-establish communication with the Sink and resume USB Default
> >>>>> Operation. The transition to vSafe5V Shall occur within tSrcTurnOn
> >>>>> (t4).
> >>>>>
> >>>>> Thanks,
> >>>>> Badhri
> >>>>>
> >>>>>>
> >>>>>>> Thanks,
> >>>>>>> Badhri
> >>>>>>>
> >>>>>>>
> >>>>>>>>> break;
> >>>>>>>>> case SRC_HARD_RESET_VBUS_ON:
> >>>>>>>>> + tcpm_set_vconn(port, true);
> >>>>>>>>> tcpm_set_vbus(port, true);
> >>>>>>>>> port->tcpc->set_pd_rx(port->tcpc, true);
> >>>>>>>>> tcpm_set_attached_state(port, true);
> >>>>>>>>> @@ -3944,7 +3950,11 @@ static void _tcpm_pd_vbus_off(struct tcpm_port *port)
> >>>>>>>>> tcpm_set_state(port, SNK_HARD_RESET_WAIT_VBUS, 0);
> >>>>>>>>> break;
> >>>>>>>>> case SRC_HARD_RESET_VBUS_OFF:
> >>>>>>>>> - tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, 0);
> >>>>>>>>> + /*
> >>>>>>>>> + * After establishing the vSafe0V voltage condition on VBUS, the Source Shall wait
> >>>>>>>>> + * tSrcRecover before re-applying VCONN and restoring VBUS to vSafe5V.
> >>>>>>>>> + */
> >>>>>>>>> + tcpm_set_state(port, SRC_HARD_RESET_VBUS_ON, PD_T_SRC_RECOVER);
> >>>>>>>>> break;
> >>>>>>>>> case HARD_RESET_SEND:
> >>>>>>>>> break;
> >>>>>>>>>
> >>>>>>>>
> >>>>
> >>
>