Re: [PATCH v1 1/1] drivers: phy: sr-usb: do not use internal fsm for USB2 phy init

From: Rayagonda Kokatanur
Date: Tue May 19 2020 - 03:14:46 EST


Hi Vinod,

On Tue, May 19, 2020 at 12:22 PM Vinod Koul <vkoul@xxxxxxxxxx> wrote:
>
> On 13-05-20, 23:09, Rayagonda Kokatanur wrote:
> > From: Bharat Gooty <bharat.gooty@xxxxxxxxxxxx>
> >
> > During different reboot cycles, USB PHY PLL may not always lock
> > during initialization and therefore can cause USB to be not usable.
>
> Ok
>
> > Hence do not use internal FSM programming sequence for the USB
> > PHY initialization.
>
> And what is the impact of not using FSM programming sequence? If not
> impact why was it added in the first place ?

We have two methods for PHY bring-up. One is the current method and
the other is the FSM programming sequence. As we have observed PHY pll
lock is not happening after long reboots, we need to use the other
method. Using current method we have tested for 500,000 reboot
iterations and always USB PHY pll lock has happened. Connected USB
devices are detected and enumerated.

Best regards,
Rayagonda
>
> > Fixes: 4dcddbb38b64 ("phy: sr-usb: Add Stingray USB PHY driver")
> > Signed-off-by: Bharat Gooty <bharat.gooty@xxxxxxxxxxxx>
> > Signed-off-by: Rayagonda Kokatanur <rayagonda.kokatanur@xxxxxxxxxxxx>
> > ---
> > drivers/phy/broadcom/phy-bcm-sr-usb.c | 55 +--------------------------
> > 1 file changed, 2 insertions(+), 53 deletions(-)
> >
> > diff --git a/drivers/phy/broadcom/phy-bcm-sr-usb.c b/drivers/phy/broadcom/phy-bcm-sr-usb.c
> > index fe6c58910e4c..7c7862b4f41f 100644
> > --- a/drivers/phy/broadcom/phy-bcm-sr-usb.c
> > +++ b/drivers/phy/broadcom/phy-bcm-sr-usb.c
> > @@ -16,8 +16,6 @@ enum bcm_usb_phy_version {
> > };
> >
> > enum bcm_usb_phy_reg {
> > - PLL_NDIV_FRAC,
> > - PLL_NDIV_INT,
> > PLL_CTRL,
> > PHY_CTRL,
> > PHY_PLL_CTRL,
> > @@ -31,18 +29,11 @@ static const u8 bcm_usb_combo_phy_ss[] = {
> > };
> >
> > static const u8 bcm_usb_combo_phy_hs[] = {
> > - [PLL_NDIV_FRAC] = 0x04,
> > - [PLL_NDIV_INT] = 0x08,
> > [PLL_CTRL] = 0x0c,
> > [PHY_CTRL] = 0x10,
> > };
> >
> > -#define HSPLL_NDIV_INT_VAL 0x13
> > -#define HSPLL_NDIV_FRAC_VAL 0x1005
> > -
> > static const u8 bcm_usb_hs_phy[] = {
> > - [PLL_NDIV_FRAC] = 0x0,
> > - [PLL_NDIV_INT] = 0x4,
> > [PLL_CTRL] = 0x8,
> > [PHY_CTRL] = 0xc,
> > };
> > @@ -52,7 +43,6 @@ enum pll_ctrl_bits {
> > SSPLL_SUSPEND_EN,
> > PLL_SEQ_START,
> > PLL_LOCK,
> > - PLL_PDIV,
> > };
> >
> > static const u8 u3pll_ctrl[] = {
> > @@ -66,29 +56,17 @@ static const u8 u3pll_ctrl[] = {
> > #define HSPLL_PDIV_VAL 0x1
> >
> > static const u8 u2pll_ctrl[] = {
> > - [PLL_PDIV] = 1,
> > [PLL_RESETB] = 5,
> > [PLL_LOCK] = 6,
> > };
> >
> > enum bcm_usb_phy_ctrl_bits {
> > CORERDY,
> > - AFE_LDO_PWRDWNB,
> > - AFE_PLL_PWRDWNB,
> > - AFE_BG_PWRDWNB,
> > - PHY_ISO,
> > PHY_RESETB,
> > PHY_PCTL,
> > };
> >
> > #define PHY_PCTL_MASK 0xffff
> > -/*
> > - * 0x0806 of PCTL_VAL has below bits set
> > - * BIT-8 : refclk divider 1
> > - * BIT-3:2: device mode; mode is not effect
> > - * BIT-1: soft reset active low
> > - */
> > -#define HSPHY_PCTL_VAL 0x0806
> > #define SSPHY_PCTL_VAL 0x0006
> >
> > static const u8 u3phy_ctrl[] = {
> > @@ -98,10 +76,6 @@ static const u8 u3phy_ctrl[] = {
> >
> > static const u8 u2phy_ctrl[] = {
> > [CORERDY] = 0,
> > - [AFE_LDO_PWRDWNB] = 1,
> > - [AFE_PLL_PWRDWNB] = 2,
> > - [AFE_BG_PWRDWNB] = 3,
> > - [PHY_ISO] = 4,
> > [PHY_RESETB] = 5,
> > [PHY_PCTL] = 6,
> > };
> > @@ -186,38 +160,13 @@ static int bcm_usb_hs_phy_init(struct bcm_usb_phy_cfg *phy_cfg)
> > int ret = 0;
> > void __iomem *regs = phy_cfg->regs;
> > const u8 *offset;
> > - u32 rd_data;
> >
> > offset = phy_cfg->offset;
> >
> > - writel(HSPLL_NDIV_INT_VAL, regs + offset[PLL_NDIV_INT]);
> > - writel(HSPLL_NDIV_FRAC_VAL, regs + offset[PLL_NDIV_FRAC]);
> > -
> > - rd_data = readl(regs + offset[PLL_CTRL]);
> > - rd_data &= ~(HSPLL_PDIV_MASK << u2pll_ctrl[PLL_PDIV]);
> > - rd_data |= (HSPLL_PDIV_VAL << u2pll_ctrl[PLL_PDIV]);
> > - writel(rd_data, regs + offset[PLL_CTRL]);
> > -
> > - /* Set Core Ready high */
> > - bcm_usb_reg32_setbits(regs + offset[PHY_CTRL],
> > - BIT(u2phy_ctrl[CORERDY]));
> > -
> > - /* Maximum timeout for Core Ready done */
> > - msleep(30);
> > -
> > + bcm_usb_reg32_clrbits(regs + offset[PLL_CTRL],
> > + BIT(u2pll_ctrl[PLL_RESETB]));
> > bcm_usb_reg32_setbits(regs + offset[PLL_CTRL],
> > BIT(u2pll_ctrl[PLL_RESETB]));
> > - bcm_usb_reg32_setbits(regs + offset[PHY_CTRL],
> > - BIT(u2phy_ctrl[PHY_RESETB]));
> > -
> > -
> > - rd_data = readl(regs + offset[PHY_CTRL]);
> > - rd_data &= ~(PHY_PCTL_MASK << u2phy_ctrl[PHY_PCTL]);
> > - rd_data |= (HSPHY_PCTL_VAL << u2phy_ctrl[PHY_PCTL]);
> > - writel(rd_data, regs + offset[PHY_CTRL]);
> > -
> > - /* Maximum timeout for PLL reset done */
> > - msleep(30);
> >
> > ret = bcm_usb_pll_lock_check(regs + offset[PLL_CTRL],
> > BIT(u2pll_ctrl[PLL_LOCK]));
> > --
> > 2.17.1
>
> --
> ~Vinod