Re: BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 in nilfs_segctor_do_co

From: Tom
Date: Thu Apr 30 2020 - 11:27:55 EST


Thank you! This is very helpful information, and does seem to be a workaround.

Like you, I have my home directory on a separate NILFS2 filesystem. As a temporary solution, I removed the line from /etc/fstab for that filesystem and added your dd suggestion along with a manual mount of the home filesystem to /etc/rc.local. /home is now mounted properly at boot with any of the newer kernels I tried.

Thanks,
Tom

On 4/30/20 5:38 AM, Hideki EIRAKU wrote:
In Msg <874kuapb2s.fsf@xxxxxxxxxx>;
Subject "Re: BUG: unable to handle kernel NULL pointer dereference at 00000000000000a8 in nilfs_segctor_do_construct":

Tomas Hlavaty <tom@xxxxxxxxxx> writes:
2) Can you mount the corrupted(?) partition from a recent version of
kernel ?

I tried the following Linux kernel versions:

- v4.19
- v5.4
- v5.5.11

and still get the crash

I found conditions to reproduce this issue with Linux 5.7-rc3:

- CONFIG_MEMCG=y *and* CONFIG_BLK_CGROUP=y

- When the NILFS2 file system writes to a device, the device file has
never written by other programs since boot

The following is an example with CONFIG_MEMCG=y and
CONFIG_BLK_CGROUP=y kernel. If you do mkfs and mount it, it works
because the mkfs command has written data to the device file before
mounting:

# mkfs -t nilfs2 /dev/sda1
mkfs.nilfs2 (nilfs-utils 2.2.7)
Start writing file system initial data to the device
Blocksize:4096 Device:/dev/sda1 Device Size:267386880
File system initialization succeeded !!
# mount /dev/sda1 /mnt
# touch /mnt
# sync
#

Loopback mount seems to be the same - if you do losetup, mkfs and
mount on a loopback device, it works:

# losetup /dev/loop0 foo
# mkfs -t nilfs2 /dev/loop0
mkfs.nilfs2 (nilfs-utils 2.2.7)
Start writing file system initial data to the device
Blocksize:4096 Device:/dev/loop0 Device Size:267386880
File system initialization succeeded !!
# mount /dev/sda1 /mnt
# touch /mnt
# sync
#

But if you do mkfs on a file and use mount -o loop, it may fail,
depending on whether the loopback device assigned by the mount command
was used or not before mounting:

# /sbin/mkfs.nilfs2 ./foo
mkfs.nilfs2 (nilfs-utils 2.2.7)
Start writing file system initial data to the device
Blocksize:4096 Device:./foo Device Size:268435456
File system initialization succeeded !!
# mount -o loop ./foo /mnt
[ 36.371331] NILFS (loop0): segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds
# touch /mnt
# sync
[ 40.252869] BUG: kernel NULL pointer dereference, address: 00000000000000a8
(snip)

After reboot, it fails:

# mount /dev/sda1 /mnt
[ 14.021188] NILFS (sda1): segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds
# touch /mnt
# sync
[ 20.576309] BUG: kernel NULL pointer dereference, address: 00000000000000a8
(snip)

But if you do dummy write to the device file before mounting, it
works:

# dd if=/dev/sda1 of=/dev/sda1 count=1
1+0 records in
1+0 records out
512 bytes copied, 0.0135982 s, 37.7 kB/s
# mount /dev/sda1 /mnt
[ 52.604560] NILFS (sda1): mounting unchecked fs
[ 52.613335] NILFS (sda1): recovery complete
[ 52.613877] NILFS (sda1): segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds
# touch /mnt
# sync
#

# losetup /dev/loop0 foo
# dd if=/dev/loop0 of=/dev/loop0 count=1
1+0 records in
1+0 records out
512 bytes copied, 0.0243797 s, 21.0 kB/s
# mount /dev/loop0 /mnt
[ 271.915595] NILFS (loop0): mounting unchecked fs
[ 272.049603] NILFS (loop0): recovery complete
[ 272.049724] NILFS (loop0): segctord starting. Construction interval = 5 seconds, CP frequency < 30 seconds
# touch /mnt
# sync
#

I think the dummy write is a simple workaround for now, unless
mounting NILFS2 at boot time. But I have been using NILFS2 /home for
years, I would like to know better workarounds.