[PATCH v2 7/8] ARM: dts: stm32: add STM32MP1-based Linux Automation MC-1 board

From: Ahmad Fatoum
Date: Thu Mar 26 2020 - 18:03:03 EST


The Linux Automation MC-1 is a SBC built around the Octavo Systems
OSD32MP15x SiP. The SiP features up to 1 GB DDR3 RAM, EEPROM and
a PMIC. The board has eMMC and a SD slot for storage and GbE
for both connectivity and power.

Signed-off-by: Ahmad Fatoum <a.fatoum@xxxxxxxxxxxxxx>
---
v1 -> v2:
- rebased on stm32-next
- moved pinctrl groups to stm32mp15-pinctrl (Alex)
- added sleep pinctrl groups
- moved enabling &gpu into SoC DTSI (Lucas)
- sorted nodes alphabetically (Alex)
- removed default-state from LED that already has linux,default-trigger
---
arch/arm/boot/dts/Makefile | 3 +-
arch/arm/boot/dts/stm32mp15-pinctrl.dtsi | 185 ++++++++++++++++
arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts | 252 ++++++++++++++++++++++
arch/arm/boot/dts/stm32mp15xx-osd32.dtsi | 230 ++++++++++++++++++++
4 files changed, 669 insertions(+), 1 deletion(-)
create mode 100644 arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
create mode 100644 arch/arm/boot/dts/stm32mp15xx-osd32.dtsi

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 527bfa4a4240..4d31eda5ba23 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -1019,7 +1019,8 @@ dtb-$(CONFIG_ARCH_STM32) += \
stm32mp157c-dhcom-pdk2.dtb \
stm32mp157c-dk2.dtb \
stm32mp157c-ed1.dtb \
- stm32mp157c-ev1.dtb
+ stm32mp157c-ev1.dtb \
+ stm32mp157c-lxa-mc1.dtb
dtb-$(CONFIG_MACH_SUN4I) += \
sun4i-a10-a1000.dtb \
sun4i-a10-ba10-tvbox.dtb \
diff --git a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
index 377a8b2b3a3a..eb85ad19c926 100644
--- a/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
+++ b/arch/arm/boot/dts/stm32mp15-pinctrl.dtsi
@@ -162,6 +162,57 @@ pins1 {
};
};

+ ethernet0_rgmii_pins_b: rgmii-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, AF11)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, AF11)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('G', 13, AF11)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, AF11)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, AF11)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, AF11)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, AF11)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('C', 1, AF11)>; /* ETH_MDC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <2>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('A', 2, AF11)>; /* ETH_MDIO */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins3 {
+ pinmux = <STM32_PINMUX('C', 4, AF11)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, AF11)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, AF11)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('H', 7, AF11)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, AF11)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, AF11)>; /* ETH_RGMII_RX_CTL */
+ bias-disable;
+ };
+ };
+
+ ethernet0_rgmii_sleep_pins_b: rgmii-sleep-1 {
+ pins1 {
+ pinmux = <STM32_PINMUX('G', 5, ANALOG)>, /* ETH_RGMII_CLK125 */
+ <STM32_PINMUX('G', 4, ANALOG)>, /* ETH_RGMII_GTX_CLK */
+ <STM32_PINMUX('G', 13, ANALOG)>, /* ETH_RGMII_TXD0 */
+ <STM32_PINMUX('G', 14, ANALOG)>, /* ETH_RGMII_TXD1 */
+ <STM32_PINMUX('C', 2, ANALOG)>, /* ETH_RGMII_TXD2 */
+ <STM32_PINMUX('E', 2, ANALOG)>, /* ETH_RGMII_TXD3 */
+ <STM32_PINMUX('B', 11, ANALOG)>, /* ETH_RGMII_TX_CTL */
+ <STM32_PINMUX('C', 1, ANALOG)>, /* ETH_MDC */
+ <STM32_PINMUX('A', 2, ANALOG)>, /* ETH_MDIO */
+ <STM32_PINMUX('C', 4, ANALOG)>, /* ETH_RGMII_RXD0 */
+ <STM32_PINMUX('C', 5, ANALOG)>, /* ETH_RGMII_RXD1 */
+ <STM32_PINMUX('H', 6, ANALOG)>, /* ETH_RGMII_RXD2 */
+ <STM32_PINMUX('H', 7, ANALOG)>, /* ETH_RGMII_RXD3 */
+ <STM32_PINMUX('A', 1, ANALOG)>, /* ETH_RGMII_RX_CLK */
+ <STM32_PINMUX('A', 7, ANALOG)>; /* ETH_RGMII_RX_CTL */
+ };
+ };
+
ethernet0_rmii_pins_a: rmii-0 {
pins1 {
pinmux = <STM32_PINMUX('G', 13, AF11)>, /* ETH1_RMII_TXD0 */
@@ -324,6 +375,23 @@ pins {
};
};

+ i2c5_pins_b: i2c5-1 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 0, AF4)>, /* I2C5_SCL */
+ <STM32_PINMUX('D', 1, AF4)>; /* I2C5_SDA */
+ bias-disable;
+ drive-open-drain;
+ slew-rate = <0>;
+ };
+ };
+
+ i2c5_sleep_pins_b: i2c5-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('D', 0, ANALOG)>, /* I2C5_SCL */
+ <STM32_PINMUX('D', 1, ANALOG)>; /* I2C5_SDA */
+ };
+ };
+
i2s2_pins_a: i2s2-0 {
pins {
pinmux = <STM32_PINMUX('I', 3, AF5)>, /* I2S2_SDO */
@@ -481,6 +549,68 @@ pins {
};
};

+ ltdc_pins_c: ltdc-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 1, AF9)>, /* LTDC_R6 */
+ <STM32_PINMUX('B', 9, AF14)>, /* LTDC_B7 */
+ <STM32_PINMUX('C', 0, AF14)>, /* LTDC_R5 */
+ <STM32_PINMUX('D', 3, AF14)>, /* LTDC_G7 */
+ <STM32_PINMUX('D', 6, AF14)>, /* LTDC_B2 */
+ <STM32_PINMUX('D', 10, AF14)>, /* LTDC_B3 */
+ <STM32_PINMUX('E', 11, AF14)>, /* LTDC_G3 */
+ <STM32_PINMUX('E', 12, AF14)>, /* LTDC_B4 */
+ <STM32_PINMUX('E', 13, AF14)>, /* LTDC_DE */
+ <STM32_PINMUX('E', 15, AF14)>, /* LTDC_R7 */
+ <STM32_PINMUX('H', 4, AF9)>, /* LTDC_G5 */
+ <STM32_PINMUX('H', 8, AF14)>, /* LTDC_R2 */
+ <STM32_PINMUX('H', 9, AF14)>, /* LTDC_R3 */
+ <STM32_PINMUX('H', 10, AF14)>, /* LTDC_R4 */
+ <STM32_PINMUX('H', 13, AF14)>, /* LTDC_G2 */
+ <STM32_PINMUX('H', 15, AF14)>, /* LTDC_G4 */
+ <STM32_PINMUX('I', 1, AF14)>, /* LTDC_G6 */
+ <STM32_PINMUX('I', 5, AF14)>, /* LTDC_B5 */
+ <STM32_PINMUX('I', 6, AF14)>, /* LTDC_B6 */
+ <STM32_PINMUX('I', 9, AF14)>, /* LTDC_VSYNC */
+ <STM32_PINMUX('I', 10, AF14)>; /* LTDC_HSYNC */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ pins2 {
+ pinmux = <STM32_PINMUX('E', 14, AF14)>; /* LTDC_CLK */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <1>;
+ };
+ };
+
+ ltdc_sleep_pins_c: ltdc-sleep-2 {
+ pins1 {
+ pinmux = <STM32_PINMUX('B', 1, ANALOG)>, /* LTDC_R6 */
+ <STM32_PINMUX('B', 9, ANALOG)>, /* LTDC_B7 */
+ <STM32_PINMUX('C', 0, ANALOG)>, /* LTDC_R5 */
+ <STM32_PINMUX('D', 3, ANALOG)>, /* LTDC_G7 */
+ <STM32_PINMUX('D', 6, ANALOG)>, /* LTDC_B2 */
+ <STM32_PINMUX('D', 10, ANALOG)>, /* LTDC_B3 */
+ <STM32_PINMUX('E', 11, ANALOG)>, /* LTDC_G3 */
+ <STM32_PINMUX('E', 12, ANALOG)>, /* LTDC_B4 */
+ <STM32_PINMUX('E', 13, ANALOG)>, /* LTDC_DE */
+ <STM32_PINMUX('E', 15, ANALOG)>, /* LTDC_R7 */
+ <STM32_PINMUX('H', 4, ANALOG)>, /* LTDC_G5 */
+ <STM32_PINMUX('H', 8, ANALOG)>, /* LTDC_R2 */
+ <STM32_PINMUX('H', 9, ANALOG)>, /* LTDC_R3 */
+ <STM32_PINMUX('H', 10, ANALOG)>, /* LTDC_R4 */
+ <STM32_PINMUX('H', 13, ANALOG)>, /* LTDC_G2 */
+ <STM32_PINMUX('H', 15, ANALOG)>, /* LTDC_G4 */
+ <STM32_PINMUX('I', 1, ANALOG)>, /* LTDC_G6 */
+ <STM32_PINMUX('I', 5, ANALOG)>, /* LTDC_B5 */
+ <STM32_PINMUX('I', 6, ANALOG)>, /* LTDC_B6 */
+ <STM32_PINMUX('I', 9, ANALOG)>, /* LTDC_VSYNC */
+ <STM32_PINMUX('I', 10, ANALOG)>, /* LTDC_HSYNC */
+ <STM32_PINMUX('E', 14, ANALOG)>; /* LTDC_CLK */
+ };
+ };
+
m_can1_pins_a: m-can1-0 {
pins1 {
pinmux = <STM32_PINMUX('H', 13, AF9)>; /* CAN1_TX */
@@ -550,6 +680,21 @@ pins {
};
};

+ pwm3_pins_b: pwm3-1 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 5, AF2)>; /* TIM3_CH2 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ };
+
+ pwm3_sleep_pins_b: pwm3-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('B', 5, ANALOG)>; /* TIM3_CH2 */
+ };
+ };
+
pwm4_pins_a: pwm4-0 {
pins {
pinmux = <STM32_PINMUX('D', 14, AF2)>, /* TIM4_CH3 */
@@ -597,6 +742,25 @@ pins {
};
};

+ pwm5_pins_b: pwm5-1 {
+ pins {
+ pinmux = <STM32_PINMUX('H', 11, AF2)>, /* TIM5_CH2 */
+ <STM32_PINMUX('H', 12, AF2)>, /* TIM5_CH3 */
+ <STM32_PINMUX('I', 0, AF2)>; /* TIM5_CH4 */
+ bias-disable;
+ drive-push-pull;
+ slew-rate = <0>;
+ };
+ };
+
+ pwm5_sleep_pins_b: pwm5-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('H', 11, ANALOG)>, /* TIM5_CH2 */
+ <STM32_PINMUX('H', 12, ANALOG)>, /* TIM5_CH3 */
+ <STM32_PINMUX('I', 0, ANALOG)>; /* TIM5_CH4 */
+ };
+ };
+
pwm8_pins_a: pwm8-0 {
pins {
pinmux = <STM32_PINMUX('I', 2, AF3)>; /* TIM8_CH4 */
@@ -987,6 +1151,27 @@ pins {
};
};

+ sdmmc2_d47_pins_b: sdmmc2-d47-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 8, AF9)>, /* SDMMC2_D4 */
+ <STM32_PINMUX('A', 9, AF10)>, /* SDMMC2_D5 */
+ <STM32_PINMUX('C', 6, AF10)>, /* SDMMC2_D6 */
+ <STM32_PINMUX('C', 7, AF10)>; /* SDMMC2_D7 */
+ slew-rate = <1>;
+ drive-push-pull;
+ bias-disable;
+ };
+ };
+
+ sdmmc2_d47_sleep_pins_b: sdmmc2-d47-sleep-1 {
+ pins {
+ pinmux = <STM32_PINMUX('A', 8, ANALOG)>, /* SDMMC2_D4 */
+ <STM32_PINMUX('A', 9, ANALOG)>, /* SDMMC2_D5 */
+ <STM32_PINMUX('C', 6, ANALOG)>, /* SDMMC2_D6 */
+ <STM32_PINMUX('C', 7, ANALOG)>; /* SDMMC2_D7 */
+ };
+ };
+
sdmmc3_b4_pins_a: sdmmc3-b4-0 {
pins1 {
pinmux = <STM32_PINMUX('F', 0, AF9)>, /* SDMMC3_D0 */
diff --git a/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
new file mode 100644
index 000000000000..5700e6b700d3
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp157c-lxa-mc1.dts
@@ -0,0 +1,252 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+/dts-v1/;
+
+#include "stm32mp157.dtsi"
+#include "stm32mp15xx-osd32.dtsi"
+#include "stm32mp15xxac-pinctrl.dtsi"
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/pwm/pwm.h>
+
+/ {
+ model = "Linux Automation MC-1 board";
+ compatible = "lxa,stm32mp157c-mc1", "st,stm32mp157";
+
+ aliases {
+ ethernet0 = &ethernet0;
+ mmc0 = &sdmmc1;
+ mmc1 = &sdmmc2;
+ serial0 = &uart4;
+ };
+
+ backlight: backlight {
+ compatible = "pwm-backlight";
+ pwms = <&backlight_pwm 1 100000 PWM_POLARITY_INVERTED>;
+ brightness-levels = <0 31 63 95 127 159 191 223 255>;
+ default-brightness-level = <7>;
+ power-supply = <&reg_5v2>; /* 3V3_BACKLIGHT */
+ };
+
+ chosen {
+ stdout-path = &uart4;
+ };
+
+ led-act {
+ compatible = "gpio-leds";
+
+ led-green {
+ label = "mc1:green:act";
+ gpios = <&gpioa 13 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+
+ led-rgb {
+ compatible = "pwm-leds";
+
+ led-red {
+ label = "mc1:red:rgb";
+ pwms = <&leds_pwm 1 1000000 0>;
+ max-brightness = <255>;
+ active-low;
+ };
+
+ led-green {
+ label = "mc1:green:rgb";
+ pwms = <&leds_pwm 2 1000000 0>;
+ max-brightness = <255>;
+ active-low;
+ };
+
+ led-blue {
+ label = "mc1:blue:rgb";
+ pwms = <&leds_pwm 3 1000000 0>;
+ max-brightness = <255>;
+ active-low;
+ };
+ };
+
+ panel: panel {
+ compatible = "edt,etm0700g0edh6", "simple-panel";
+ backlight = <&backlight>;
+ enable-gpios = <&gpiod 4 GPIO_ACTIVE_HIGH>;
+ power-supply = <&reg_3v3>;
+
+ port {
+ panel_input: endpoint {
+ remote-endpoint = <&ltdc_ep0_out>;
+ };
+ };
+ };
+
+ reg_3v3: regulator_3v3 {
+ compatible = "regulator-fixed";
+ regulator-name = "3V3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ vin-supply = <&v3v3>;
+ };
+
+ /* supplied by either debug board or PoE */
+ reg_5v2: regulator_5v2 {
+ compatible = "regulator-fixed";
+ regulator-name = "5V2";
+ regulator-min-microvolt = <5200000>;
+ regulator-max-microvolt = <5200000>;
+ regulator-always-on;
+ };
+};
+
+&ethernet0 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&ethernet0_rgmii_pins_b>;
+ pinctrl-1 = <&ethernet0_rgmii_sleep_pins_b>;
+ phy-mode = "rgmii-id";
+ phy-handle = <&ethphy>;
+ status = "okay";
+
+ mdio0 {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ ethphy: ethernet-phy@3 { /* KSZ9031RN */
+ reg = <3>;
+ reset-gpios = <&gpiog 0 GPIO_ACTIVE_LOW>; /* ETH_RST# */
+ interrupt-parent = <&gpioa>;
+ interrupts = <6 IRQ_TYPE_EDGE_FALLING>; /* ETH_MDINT# */
+ rxc-skew-ps = <1860>;
+ txc-skew-ps = <1860>;
+ reset-assert-us = <10000>;
+ reset-deassert-us = <300>;
+ micrel,force-master;
+ };
+ };
+};
+
+&gpioz {
+ gpio-line-names = "HWID0", "HWID1", "HWID2", "HWID3", "", "",
+ "HWID4", "HWID5";
+};
+
+&i2c5 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c5_pins_b>;
+ pinctrl-1 = <&i2c5_sleep_pins_b>;
+ clock-frequency = <400000>;
+ status = "okay";
+
+ touchscreen@38 {
+ compatible = "edt,edt-ft5x06";
+ interrupt-parent = <&gpiod>;
+ interrupts = <11 IRQ_TYPE_EDGE_FALLING>; /* TOUCH_INT# */
+ vcc-supply = <&reg_3v3>;
+ reg = <0x38>;
+ reset-gpios = <&gpiof 8 GPIO_ACTIVE_LOW>; /* TOUCH_RESET# */
+ touchscreen-size-x = <1792>;
+ touchscreen-size-y = <1024>;
+ wakeup-source;
+ };
+};
+
+&ltdc {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&ltdc_pins_c>;
+ pinctrl-1 = <&ltdc_sleep_pins_c>;
+ status = "okay";
+
+ port {
+ ltdc_ep0_out: endpoint@0 {
+ reg = <0>;
+ remote-endpoint = <&panel_input>;
+ };
+ };
+};
+
+&pmic {
+ regulators {
+ buck4-supply = <&reg_5v2>; /* VIN */
+ ldo2-supply = <&reg_5v2>; /* PMIC_LDO25IN */
+ ldo5-supply = <&reg_5v2>; /* PMIC_LDO25IN */
+ boost-supply = <&reg_5v2>; /* PMIC_BSTIN */
+ pwr_sw2-supply = <&bst_out>; /* PMIC_SWIN */
+ };
+};
+
+&sdmmc1 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc1_b4_pins_a>;
+ pinctrl-1 = <&sdmmc1_b4_od_pins_a>;
+ pinctrl-2 = <&sdmmc1_b4_sleep_pins_a>;
+ bus-width = <4>;
+ cd-gpios = <&gpioh 3 GPIO_ACTIVE_LOW>;
+ disable-wp;
+ no-1-8-v;
+ st,neg-edge;
+ vmmc-supply = <&reg_3v3>;
+ status = "okay";
+};
+
+&sdmmc1_b4_pins_a {
+ /*
+ * board lacks external pull-ups on SDMMC lines. Class 10 SD refuses to
+ * work, thus enable internal pull-ups.
+ */
+ pins1 {
+ /delete-property/ bias-disable;
+ bias-pull-up;
+ };
+ pins2 {
+ /delete-property/ bias-disable;
+ bias-pull-up;
+ };
+};
+
+&sdmmc2 {
+ pinctrl-names = "default", "opendrain", "sleep";
+ pinctrl-0 = <&sdmmc2_b4_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-1 = <&sdmmc2_b4_od_pins_a &sdmmc2_d47_pins_b>;
+ pinctrl-2 = <&sdmmc2_b4_sleep_pins_a &sdmmc2_d47_sleep_pins_b>;
+ bus-width = <8>;
+ no-1-8-v;
+ no-sd;
+ no-sdio;
+ non-removable;
+ st,neg-edge;
+ vmmc-supply = <&reg_3v3>;
+ status = "okay";
+};
+
+&timers3 {
+ status = "okay";
+
+ backlight_pwm: pwm {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pwm3_pins_b>;
+ pinctrl-1 = <&pwm3_sleep_pins_b>;
+ status = "okay";
+ };
+};
+
+&timers5 {
+ status = "okay";
+
+ leds_pwm: pwm {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&pwm5_pins_b>;
+ pinctrl-1 = <&pwm5_sleep_pins_b>;
+ status = "okay";
+ };
+};
+
+&uart4 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&uart4_pins_a>;
+ status = "okay";
+};
diff --git a/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
new file mode 100644
index 000000000000..713485a95795
--- /dev/null
+++ b/arch/arm/boot/dts/stm32mp15xx-osd32.dtsi
@@ -0,0 +1,230 @@
+/* SPDX-License-Identifier: (GPL-2.0-or-later OR BSD-3-Clause) */
+/*
+ * Copyright (C) 2020 STMicroelectronics - All Rights Reserved
+ * Copyright (C) 2020 Ahmad Fatoum, Pengutronix
+ */
+
+#include "stm32mp15-pinctrl.dtsi"
+
+#include <dt-bindings/mfd/st,stpmic1.h>
+
+/ {
+ reserved-memory {
+ #address-cells = <1>;
+ #size-cells = <1>;
+ ranges;
+
+ mcuram2: mcuram2@10000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10000000 0x40000>;
+ no-map;
+ };
+
+ vdev0vring0: vdev0vring0@10040000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10040000 0x1000>;
+ no-map;
+ };
+
+ vdev0vring1: vdev0vring1@10041000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10041000 0x1000>;
+ no-map;
+ };
+
+ vdev0buffer: vdev0buffer@10042000 {
+ compatible = "shared-dma-pool";
+ reg = <0x10042000 0x4000>;
+ no-map;
+ };
+
+ mcuram: mcuram@30000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x30000000 0x40000>;
+ no-map;
+ };
+
+ retram: retram@38000000 {
+ compatible = "shared-dma-pool";
+ reg = <0x38000000 0x10000>;
+ no-map;
+ };
+ };
+
+ reg_sip_eeprom: regulator_eeprom {
+ compatible = "regulator-fixed";
+ regulator-name = "sip_eeprom";
+ regulator-always-on;
+ };
+};
+
+&i2c4 {
+ pinctrl-names = "default", "sleep";
+ pinctrl-0 = <&i2c4_pins_a>;
+ pinctrl-1 = <&i2c4_sleep_pins_a>;
+ clock-frequency = <400000>;
+ i2c-scl-rising-time-ns = <185>;
+ i2c-scl-falling-time-ns = <20>;
+ status = "okay";
+
+ pmic: stpmic@33 {
+ compatible = "st,stpmic1";
+ reg = <0x33>;
+ interrupts-extended = <&gpioa 0 IRQ_TYPE_EDGE_FALLING>;
+ interrupt-controller;
+ #interrupt-cells = <2>;
+
+ regulators {
+ compatible = "st,stpmic1-regulators";
+
+ ldo1-supply = <&v3v3>;
+ ldo6-supply = <&v3v3>;
+ pwr_sw1-supply = <&bst_out>;
+
+ vddcore: buck1 {
+ regulator-name = "vddcore";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd_ddr: buck2 {
+ regulator-name = "vdd_ddr";
+ regulator-min-microvolt = <1350000>;
+ regulator-max-microvolt = <1350000>;
+ regulator-always-on;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ vdd: buck3 {
+ regulator-name = "vdd";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ st,mask-reset;
+ regulator-initial-mode = <0>;
+ regulator-over-current-protection;
+ };
+
+ v3v3: buck4 {
+ regulator-name = "v3v3";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ regulator-initial-mode = <0>;
+ };
+
+ v1v8_audio: ldo1 {
+ regulator-name = "v1v8_audio";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO1 0>;
+
+ };
+
+ v3v3_hdmi: ldo2 {
+ regulator-name = "v3v3_hdmi";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO2 0>;
+
+ };
+
+ vtt_ddr: ldo3 {
+ regulator-name = "vtt_ddr";
+ regulator-min-microvolt = <500000>;
+ regulator-max-microvolt = <750000>;
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ vdd_usb: ldo4 {
+ regulator-name = "vdd_usb";
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+ interrupts = <IT_CURLIM_LDO4 0>;
+ };
+
+ vdda: ldo5 {
+ regulator-name = "vdda";
+ regulator-min-microvolt = <2900000>;
+ regulator-max-microvolt = <2900000>;
+ interrupts = <IT_CURLIM_LDO5 0>;
+ regulator-boot-on;
+ };
+
+ v1v2_hdmi: ldo6 {
+ regulator-name = "v1v2_hdmi";
+ regulator-min-microvolt = <1200000>;
+ regulator-max-microvolt = <1200000>;
+ regulator-always-on;
+ interrupts = <IT_CURLIM_LDO6 0>;
+
+ };
+
+ vref_ddr: vref_ddr {
+ regulator-name = "vref_ddr";
+ regulator-always-on;
+ regulator-over-current-protection;
+ };
+
+ bst_out: boost {
+ regulator-name = "bst_out";
+ interrupts = <IT_OCP_BOOST 0>;
+ };
+
+ vbus_otg: pwr_sw1 {
+ regulator-name = "vbus_otg";
+ interrupts = <IT_OCP_OTG 0>;
+ regulator-active-discharge;
+ };
+
+ vbus_sw: pwr_sw2 {
+ regulator-name = "vbus_sw";
+ interrupts = <IT_OCP_SWOUT 0>;
+ regulator-active-discharge;
+ };
+ };
+
+ onkey {
+ compatible = "st,stpmic1-onkey";
+ interrupts = <IT_PONKEY_F 0>, <IT_PONKEY_R 1>;
+ interrupt-names = "onkey-falling", "onkey-rising";
+ };
+
+ pmic_watchdog: watchdog {
+ compatible = "st,stpmic1-wdt";
+ status = "disabled";
+ };
+ };
+
+ sip_eeprom: eeprom@50 {
+ compatible = "atmel,24c32";
+ vcc-supply = <&reg_sip_eeprom>;
+ reg = <0x50>;
+ };
+};
+
+&ipcc {
+ status = "okay";
+};
+
+&m4_rproc {
+ memory-region = <&retram>, <&mcuram>, <&mcuram2>, <&vdev0vring0>,
+ <&vdev0vring1>, <&vdev0buffer>;
+ mboxes = <&ipcc 0>, <&ipcc 1>, <&ipcc 2>;
+ mbox-names = "vq0", "vq1", "shutdown";
+ interrupt-parent = <&exti>;
+ interrupts = <68 1>;
+ status = "okay";
+};
+
+&rng1 {
+ status = "okay";
+};
--
2.26.0.rc2