[PATCH v4 06/20] usb: phy: tegra: Perform general clean up of the code

From: Dmitry Osipenko
Date: Sun Jan 05 2020 - 20:35:46 EST

This patch fixes few dozens of legit checkpatch warnings, adds missed
handling of potential error-cases and prettifies code where makes sense.
All these clean-up changes are quite minor and do not fix any real
problems.

Acked-by: Thierry Reding <treding@xxxxxxxxxx>
Signed-off-by: Dmitry Osipenko <digetx@xxxxxxxxx>
---
drivers/usb/phy/phy-tegra-usb.c | 485 +++++++++++++++++---------------
1 file changed, 254 insertions(+), 231 deletions(-)

diff --git a/drivers/usb/phy/phy-tegra-usb.c b/drivers/usb/phy/phy-tegra-usb.c
index 664259d74658..c045f44ea964 100644
--- a/drivers/usb/phy/phy-tegra-usb.c
+++ b/drivers/usb/phy/phy-tegra-usb.c
@@ -28,35 +28,35 @@
#include <linux/usb/tegra_usb_phy.h>
#include <linux/regulator/consumer.h>

-#define ULPI_VIEWPORT 0x170
+#define ULPI_VIEWPORT 0x170

/* PORTSC PTS/PHCD bits, Tegra20 only */
-#define TEGRA_USB_PORTSC1 0x184
-#define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30)
-#define TEGRA_USB_PORTSC1_PHCD (1 << 23)
+#define TEGRA_USB_PORTSC1 0x184
+#define TEGRA_USB_PORTSC1_PTS(x) (((x) & 0x3) << 30)
+#define TEGRA_USB_PORTSC1_PHCD BIT(23)

/* HOSTPC1 PTS/PHCD bits, Tegra30 and above */
-#define TEGRA_USB_HOSTPC1_DEVLC 0x1b4
-#define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29)
-#define TEGRA_USB_HOSTPC1_DEVLC_PHCD (1 << 22)
+#define TEGRA_USB_HOSTPC1_DEVLC 0x1b4
+#define TEGRA_USB_HOSTPC1_DEVLC_PTS(x) (((x) & 0x7) << 29)
+#define TEGRA_USB_HOSTPC1_DEVLC_PHCD BIT(22)

/* Bits of PORTSC1, which will get cleared by writing 1 into them */
#define TEGRA_PORTSC1_RWC_BITS (PORT_CSC | PORT_PEC | PORT_OCC)

-#define USB_SUSP_CTRL 0x400
-#define USB_WAKE_ON_CNNT_EN_DEV (1 << 3)
-#define USB_WAKE_ON_DISCON_EN_DEV (1 << 4)
-#define USB_SUSP_CLR (1 << 5)
-#define USB_PHY_CLK_VALID (1 << 7)
-#define UTMIP_RESET (1 << 11)
-#define UHSIC_RESET (1 << 11)
-#define UTMIP_PHY_ENABLE (1 << 12)
-#define ULPI_PHY_ENABLE (1 << 13)
-#define USB_SUSP_SET (1 << 14)
-#define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16)
-
-#define USB1_LEGACY_CTRL 0x410
-#define USB1_NO_LEGACY_MODE (1 << 0)
+#define USB_SUSP_CTRL 0x400
+#define USB_WAKE_ON_CNNT_EN_DEV BIT(3)
+#define USB_WAKE_ON_DISCON_EN_DEV BIT(4)
+#define USB_SUSP_CLR BIT(5)
+#define USB_PHY_CLK_VALID BIT(7)
+#define UTMIP_RESET BIT(11)
+#define UHSIC_RESET BIT(11)
+#define UTMIP_PHY_ENABLE BIT(12)
+#define ULPI_PHY_ENABLE BIT(13)
+#define USB_SUSP_SET BIT(14)
+#define USB_WAKEUP_DEBOUNCE_COUNT(x) (((x) & 0x7) << 16)
+
+#define USB1_LEGACY_CTRL 0x410
+#define USB1_NO_LEGACY_MODE BIT(0)
#define USB1_VBUS_SENSE_CTL_MASK (3 << 1)
#define USB1_VBUS_SENSE_CTL_VBUS_WAKEUP (0 << 1)
#define USB1_VBUS_SENSE_CTL_AB_SESS_VLD_OR_VBUS_WAKEUP \
@@ -64,94 +64,94 @@
#define USB1_VBUS_SENSE_CTL_AB_SESS_VLD (2 << 1)
#define USB1_VBUS_SENSE_CTL_A_SESS_VLD (3 << 1)

-#define ULPI_TIMING_CTRL_0 0x424
-#define ULPI_OUTPUT_PINMUX_BYP (1 << 10)
-#define ULPI_CLKOUT_PINMUX_BYP (1 << 11)
+#define ULPI_TIMING_CTRL_0 0x424
+#define ULPI_OUTPUT_PINMUX_BYP BIT(10)
+#define ULPI_CLKOUT_PINMUX_BYP BIT(11)

-#define ULPI_TIMING_CTRL_1 0x428
-#define ULPI_DATA_TRIMMER_LOAD (1 << 0)
-#define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1)
-#define ULPI_STPDIRNXT_TRIMMER_LOAD (1 << 16)
-#define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17)
-#define ULPI_DIR_TRIMMER_LOAD (1 << 24)
-#define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25)
+#define ULPI_TIMING_CTRL_1 0x428
+#define ULPI_DATA_TRIMMER_LOAD BIT(0)
+#define ULPI_DATA_TRIMMER_SEL(x) (((x) & 0x7) << 1)
+#define ULPI_STPDIRNXT_TRIMMER_LOAD BIT(16)
+#define ULPI_STPDIRNXT_TRIMMER_SEL(x) (((x) & 0x7) << 17)
+#define ULPI_DIR_TRIMMER_LOAD BIT(24)
+#define ULPI_DIR_TRIMMER_SEL(x) (((x) & 0x7) << 25)

-#define UTMIP_PLL_CFG1 0x804
+#define UTMIP_PLL_CFG1 0x804
#define UTMIP_XTAL_FREQ_COUNT(x) (((x) & 0xfff) << 0)
#define UTMIP_PLLU_ENABLE_DLY_COUNT(x) (((x) & 0x1f) << 27)

-#define UTMIP_XCVR_CFG0 0x808
+#define UTMIP_XCVR_CFG0 0x808
#define UTMIP_XCVR_SETUP(x) (((x) & 0xf) << 0)
#define UTMIP_XCVR_SETUP_MSB(x) ((((x) & 0x70) >> 4) << 22)
#define UTMIP_XCVR_LSRSLEW(x) (((x) & 0x3) << 8)
#define UTMIP_XCVR_LSFSLEW(x) (((x) & 0x3) << 10)
-#define UTMIP_FORCE_PD_POWERDOWN (1 << 14)
-#define UTMIP_FORCE_PD2_POWERDOWN (1 << 16)
-#define UTMIP_FORCE_PDZI_POWERDOWN (1 << 18)
-#define UTMIP_XCVR_LSBIAS_SEL (1 << 21)
+#define UTMIP_FORCE_PD_POWERDOWN BIT(14)
+#define UTMIP_FORCE_PD2_POWERDOWN BIT(16)
+#define UTMIP_FORCE_PDZI_POWERDOWN BIT(18)
+#define UTMIP_XCVR_LSBIAS_SEL BIT(21)
#define UTMIP_XCVR_HSSLEW(x) (((x) & 0x3) << 4)
#define UTMIP_XCVR_HSSLEW_MSB(x) ((((x) & 0x1fc) >> 2) << 25)

-#define UTMIP_BIAS_CFG0 0x80c
-#define UTMIP_OTGPD (1 << 11)
-#define UTMIP_BIASPD (1 << 10)
-#define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0)
-#define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2)
-#define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24)
+#define UTMIP_BIAS_CFG0 0x80c
+#define UTMIP_OTGPD BIT(11)
+#define UTMIP_BIASPD BIT(10)
+#define UTMIP_HSSQUELCH_LEVEL(x) (((x) & 0x3) << 0)
+#define UTMIP_HSDISCON_LEVEL(x) (((x) & 0x3) << 2)
+#define UTMIP_HSDISCON_LEVEL_MSB(x) ((((x) & 0x4) >> 2) << 24)

-#define UTMIP_HSRX_CFG0 0x810
-#define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10)
-#define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15)
+#define UTMIP_HSRX_CFG0 0x810
+#define UTMIP_ELASTIC_LIMIT(x) (((x) & 0x1f) << 10)
+#define UTMIP_IDLE_WAIT(x) (((x) & 0x1f) << 15)

-#define UTMIP_HSRX_CFG1 0x814
-#define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1)
+#define UTMIP_HSRX_CFG1 0x814
+#define UTMIP_HS_SYNC_START_DLY(x) (((x) & 0x1f) << 1)

-#define UTMIP_TX_CFG0 0x820
-#define UTMIP_FS_PREABMLE_J (1 << 19)
-#define UTMIP_HS_DISCON_DISABLE (1 << 8)
+#define UTMIP_TX_CFG0 0x820
+#define UTMIP_FS_PREABMLE_J BIT(19)
+#define UTMIP_HS_DISCON_DISABLE BIT(8)

-#define UTMIP_MISC_CFG0 0x824
-#define UTMIP_DPDM_OBSERVE (1 << 26)
-#define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27)
-#define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf)
-#define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe)
-#define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd)
-#define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc)
-#define UTMIP_SUSPEND_EXIT_ON_EDGE (1 << 22)
+#define UTMIP_MISC_CFG0 0x824
+#define UTMIP_DPDM_OBSERVE BIT(26)
+#define UTMIP_DPDM_OBSERVE_SEL(x) (((x) & 0xf) << 27)
+#define UTMIP_DPDM_OBSERVE_SEL_FS_J UTMIP_DPDM_OBSERVE_SEL(0xf)
+#define UTMIP_DPDM_OBSERVE_SEL_FS_K UTMIP_DPDM_OBSERVE_SEL(0xe)
+#define UTMIP_DPDM_OBSERVE_SEL_FS_SE1 UTMIP_DPDM_OBSERVE_SEL(0xd)
+#define UTMIP_DPDM_OBSERVE_SEL_FS_SE0 UTMIP_DPDM_OBSERVE_SEL(0xc)
+#define UTMIP_SUSPEND_EXIT_ON_EDGE BIT(22)

-#define UTMIP_MISC_CFG1 0x828
-#define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18)
-#define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6)
+#define UTMIP_MISC_CFG1 0x828
+#define UTMIP_PLL_ACTIVE_DLY_COUNT(x) (((x) & 0x1f) << 18)
+#define UTMIP_PLLU_STABLE_COUNT(x) (((x) & 0xfff) << 6)

-#define UTMIP_DEBOUNCE_CFG0 0x82c
-#define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0)
+#define UTMIP_DEBOUNCE_CFG0 0x82c
+#define UTMIP_BIAS_DEBOUNCE_A(x) (((x) & 0xffff) << 0)

-#define UTMIP_BAT_CHRG_CFG0 0x830
-#define UTMIP_PD_CHRG (1 << 0)
+#define UTMIP_BAT_CHRG_CFG0 0x830
+#define UTMIP_PD_CHRG BIT(0)

-#define UTMIP_SPARE_CFG0 0x834
-#define FUSE_SETUP_SEL (1 << 3)
+#define UTMIP_SPARE_CFG0 0x834
+#define FUSE_SETUP_SEL BIT(3)

-#define UTMIP_XCVR_CFG1 0x838
-#define UTMIP_FORCE_PDDISC_POWERDOWN (1 << 0)
-#define UTMIP_FORCE_PDCHRP_POWERDOWN (1 << 2)
-#define UTMIP_FORCE_PDDR_POWERDOWN (1 << 4)
-#define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18)
+#define UTMIP_XCVR_CFG1 0x838
+#define UTMIP_FORCE_PDDISC_POWERDOWN BIT(0)
+#define UTMIP_FORCE_PDCHRP_POWERDOWN BIT(2)
+#define UTMIP_FORCE_PDDR_POWERDOWN BIT(4)
+#define UTMIP_XCVR_TERM_RANGE_ADJ(x) (((x) & 0xf) << 18)

-#define UTMIP_BIAS_CFG1 0x83c
-#define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3)
+#define UTMIP_BIAS_CFG1 0x83c
+#define UTMIP_BIAS_PDTRK_COUNT(x) (((x) & 0x1f) << 3)

/* For Tegra30 and above only, the address is different in Tegra20 */
-#define USB_USBMODE 0x1f8
-#define USB_USBMODE_MASK (3 << 0)
-#define USB_USBMODE_HOST (3 << 0)
-#define USB_USBMODE_DEVICE (2 << 0)
+#define USB_USBMODE 0x1f8
+#define USB_USBMODE_MASK (3 << 0)
+#define USB_USBMODE_HOST (3 << 0)
+#define USB_USBMODE_DEVICE (2 << 0)

static DEFINE_SPINLOCK(utmip_pad_lock);
-static int utmip_pad_count;
+static unsigned int utmip_pad_count;

struct tegra_xtal_freq {
- int freq;
+ unsigned int freq;
u8 enable_delay;
u8 stable_count;
u8 active_delay;
@@ -194,6 +194,11 @@ static const struct tegra_xtal_freq tegra_freq_table[] = {
},
};

+static inline struct tegra_usb_phy *to_tegra_usb_phy(struct usb_phy *u_phy)
+{
+ return container_of(u_phy, struct tegra_usb_phy, u_phy);
+}
+
static void set_pts(struct tegra_usb_phy *phy, u8 pts_val)
{
void __iomem *base = phy->regs;
@@ -298,13 +303,16 @@ static int utmip_pad_close(struct tegra_usb_phy *phy)
return ret;
}

-static void utmip_pad_power_on(struct tegra_usb_phy *phy)
+static int utmip_pad_power_on(struct tegra_usb_phy *phy)
{
- unsigned long val, flags;
- void __iomem *base = phy->pad_regs;
struct tegra_utmip_config *config = phy->config;
+ void __iomem *base = phy->pad_regs;
+ unsigned long val, flags;
+ int err;

- clk_prepare_enable(phy->pad_clk);
+ err = clk_prepare_enable(phy->pad_clk);
+ if (err)
+ return err;

spin_lock_irqsave(&utmip_pad_lock, flags);

@@ -327,19 +335,24 @@ static void utmip_pad_power_on(struct tegra_usb_phy *phy)
spin_unlock_irqrestore(&utmip_pad_lock, flags);

clk_disable_unprepare(phy->pad_clk);
+
+ return 0;
}

static int utmip_pad_power_off(struct tegra_usb_phy *phy)
{
- unsigned long val, flags;
void __iomem *base = phy->pad_regs;
+ unsigned long val, flags;
+ int err;

if (!utmip_pad_count) {
dev_err(phy->u_phy.dev, "UTMIP pad already powered off\n");
return -EINVAL;
}

- clk_prepare_enable(phy->pad_clk);
+ err = clk_prepare_enable(phy->pad_clk);
+ if (err)
+ return err;

spin_lock_irqsave(&utmip_pad_lock, flags);

@@ -366,8 +379,8 @@ static int utmi_wait_register(void __iomem *reg, u32 mask, u32 result)

static void utmi_phy_clk_disable(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

/*
* The USB driver may have already initiated the phy clock
@@ -382,23 +395,24 @@ static void utmi_phy_clk_disable(struct tegra_usb_phy *phy)
val |= USB_SUSP_SET;
writel(val, base + USB_SUSP_CTRL);

- udelay(10);
+ usleep_range(10, 100);

val = readl(base + USB_SUSP_CTRL);
val &= ~USB_SUSP_SET;
writel(val, base + USB_SUSP_CTRL);
- } else
+ } else {
set_phcd(phy, true);
+ }

- if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0) < 0)
+ if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID, 0))
dev_err(phy->u_phy.dev,
"Timeout waiting for PHY to stabilize on disable\n");
}

static void utmi_phy_clk_enable(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

/*
* The USB driver may have already initiated the phy clock
@@ -414,25 +428,27 @@ static void utmi_phy_clk_enable(struct tegra_usb_phy *phy)
val |= USB_SUSP_CLR;
writel(val, base + USB_SUSP_CTRL);

- udelay(10);
+ usleep_range(10, 100);

val = readl(base + USB_SUSP_CTRL);
val &= ~USB_SUSP_CLR;
writel(val, base + USB_SUSP_CTRL);
- } else
+ } else {
set_phcd(phy, false);
+ }

if (utmi_wait_register(base + USB_SUSP_CTRL, USB_PHY_CLK_VALID,
- USB_PHY_CLK_VALID))
+ USB_PHY_CLK_VALID))
dev_err(phy->u_phy.dev,
"Timeout waiting for PHY to stabilize on enable\n");
}

static int utmi_phy_power_on(struct tegra_usb_phy *phy)
{
- unsigned long val;
- void __iomem *base = phy->regs;
struct tegra_utmip_config *config = phy->config;
+ void __iomem *base = phy->regs;
+ unsigned long val;
+ int err;

val = readl(base + USB_SUSP_CTRL);
val |= UTMIP_RESET;
@@ -498,7 +514,9 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy)
writel(val, base + UTMIP_BAT_CHRG_CFG0);
}

- utmip_pad_power_on(phy);
+ err = utmip_pad_power_on(phy);
+ if (err)
+ return err;

val = readl(base + UTMIP_XCVR_CFG0);
val &= ~(UTMIP_FORCE_PD_POWERDOWN | UTMIP_FORCE_PD2_POWERDOWN |
@@ -579,8 +597,8 @@ static int utmi_phy_power_on(struct tegra_usb_phy *phy)

static int utmi_phy_power_off(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

utmi_phy_clk_disable(phy);

@@ -614,8 +632,8 @@ static int utmi_phy_power_off(struct tegra_usb_phy *phy)

static void utmi_phy_preresume(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

val = readl(base + UTMIP_TX_CFG0);
val |= UTMIP_HS_DISCON_DISABLE;
@@ -624,8 +642,8 @@ static void utmi_phy_preresume(struct tegra_usb_phy *phy)

static void utmi_phy_postresume(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

val = readl(base + UTMIP_TX_CFG0);
val &= ~UTMIP_HS_DISCON_DISABLE;
@@ -635,8 +653,8 @@ static void utmi_phy_postresume(struct tegra_usb_phy *phy)
static void utmi_phy_restore_start(struct tegra_usb_phy *phy,
enum tegra_usb_phy_port_speed port_speed)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

val = readl(base + UTMIP_MISC_CFG0);
val &= ~UTMIP_DPDM_OBSERVE_SEL(~0);
@@ -645,47 +663,52 @@ static void utmi_phy_restore_start(struct tegra_usb_phy *phy,
else
val |= UTMIP_DPDM_OBSERVE_SEL_FS_J;
writel(val, base + UTMIP_MISC_CFG0);
- udelay(1);
+ usleep_range(1, 10);

val = readl(base + UTMIP_MISC_CFG0);
val |= UTMIP_DPDM_OBSERVE;
writel(val, base + UTMIP_MISC_CFG0);
- udelay(10);
+ usleep_range(10, 100);
}

static void utmi_phy_restore_end(struct tegra_usb_phy *phy)
{
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;

val = readl(base + UTMIP_MISC_CFG0);
val &= ~UTMIP_DPDM_OBSERVE;
writel(val, base + UTMIP_MISC_CFG0);
- udelay(10);
+ usleep_range(10, 100);
}

static int ulpi_phy_power_on(struct tegra_usb_phy *phy)
{
- int ret;
- unsigned long val;
void __iomem *base = phy->regs;
+ unsigned long val;
+ int err;

- ret = gpio_direction_output(phy->reset_gpio, 0);
- if (ret < 0) {
+ err = gpio_direction_output(phy->reset_gpio, 0);
+ if (err) {
dev_err(phy->u_phy.dev, "GPIO %d not set to 0: %d\n",
- phy->reset_gpio, ret);
- return ret;
+ phy->reset_gpio, err);
+ return err;
}
- msleep(5);
- ret = gpio_direction_output(phy->reset_gpio, 1);
- if (ret < 0) {
+
+ err = clk_prepare_enable(phy->clk);
+ if (err)
+ return err;
+
+ usleep_range(5000, 6000);
+
+ err = gpio_direction_output(phy->reset_gpio, 1);
+ if (err) {
dev_err(phy->u_phy.dev, "GPIO %d not set to 1: %d\n",
- phy->reset_gpio, ret);
- return ret;
+ phy->reset_gpio, err);
+ goto disable_clk;
}

- clk_prepare_enable(phy->clk);
- msleep(1);
+ usleep_range(1000, 2000);

val = readl(base + USB_SUSP_CTRL);
val |= UHSIC_RESET;
@@ -706,7 +729,7 @@ static int ulpi_phy_power_on(struct tegra_usb_phy *phy)
val |= ULPI_STPDIRNXT_TRIMMER_SEL(4);
val |= ULPI_DIR_TRIMMER_SEL(4);
writel(val, base + ULPI_TIMING_CTRL_1);
- udelay(10);
+ usleep_range(10, 100);

val |= ULPI_DATA_TRIMMER_LOAD;
val |= ULPI_STPDIRNXT_TRIMMER_LOAD;
@@ -714,28 +737,33 @@ static int ulpi_phy_power_on(struct tegra_usb_phy *phy)
writel(val, base + ULPI_TIMING_CTRL_1);

/* Fix VbusInvalid due to floating VBUS */
- ret = usb_phy_io_write(phy->ulpi, 0x40, 0x08);
- if (ret) {
- dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret);
- return ret;
+ err = usb_phy_io_write(phy->ulpi, 0x40, 0x08);
+ if (err) {
+ dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err);
+ goto disable_clk;
}

- ret = usb_phy_io_write(phy->ulpi, 0x80, 0x0B);
- if (ret) {
- dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", ret);
- return ret;
+ err = usb_phy_io_write(phy->ulpi, 0x80, 0x0B);
+ if (err) {
+ dev_err(phy->u_phy.dev, "ULPI write failed: %d\n", err);
+ goto disable_clk;
}

val = readl(base + USB_SUSP_CTRL);
val |= USB_SUSP_CLR;
writel(val, base + USB_SUSP_CTRL);
- udelay(100);
+ usleep_range(100, 1000);

val = readl(base + USB_SUSP_CTRL);
val &= ~USB_SUSP_CLR;
writel(val, base + USB_SUSP_CTRL);

return 0;
+
+disable_clk:
+ clk_disable_unprepare(phy->clk);
+
+ return err;
}

static int ulpi_phy_power_off(struct tegra_usb_phy *phy)
@@ -795,8 +823,7 @@ static int tegra_usb_phy_power_off(struct tegra_usb_phy *phy)

static void tegra_usb_phy_shutdown(struct usb_phy *u_phy)
{
- struct tegra_usb_phy *phy = container_of(u_phy, struct tegra_usb_phy,
- u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (WARN_ON(!phy->freq))
return;
@@ -814,9 +841,9 @@ static void tegra_usb_phy_shutdown(struct usb_phy *u_phy)
phy->freq = NULL;
}

-static int tegra_usb_phy_set_suspend(struct usb_phy *x, int suspend)
+static int tegra_usb_phy_set_suspend(struct usb_phy *u_phy, int suspend)
{
- struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (WARN_ON(!phy->freq))
return -EINVAL;
@@ -832,7 +859,7 @@ static int ulpi_open(struct tegra_usb_phy *phy)
int err;

err = gpio_direction_output(phy->reset_gpio, 0);
- if (err < 0) {
+ if (err) {
dev_err(phy->u_phy.dev,
"ULPI reset GPIO %d direction not asserted: %d\n",
phy->reset_gpio, err);
@@ -844,10 +871,9 @@ static int ulpi_open(struct tegra_usb_phy *phy)

static int tegra_usb_phy_init(struct usb_phy *u_phy)
{
- struct tegra_usb_phy *phy = container_of(u_phy, struct tegra_usb_phy,
- u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);
unsigned long parent_rate;
- int i;
+ unsigned int i;
int err;

if (WARN_ON(phy->freq))
@@ -885,7 +911,7 @@ static int tegra_usb_phy_init(struct usb_phy *u_phy)
err = ulpi_open(phy);
else
err = utmip_pad_open(phy);
- if (err < 0)
+ if (err)
goto fail;

err = tegra_usb_phy_power_on(phy);
@@ -905,37 +931,37 @@ static int tegra_usb_phy_init(struct usb_phy *u_phy)
return err;
}

-void tegra_usb_phy_preresume(struct usb_phy *x)
+void tegra_usb_phy_preresume(struct usb_phy *u_phy)
{
- struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (!phy->is_ulpi_phy)
utmi_phy_preresume(phy);
}
EXPORT_SYMBOL_GPL(tegra_usb_phy_preresume);

-void tegra_usb_phy_postresume(struct usb_phy *x)
+void tegra_usb_phy_postresume(struct usb_phy *u_phy)
{
- struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (!phy->is_ulpi_phy)
utmi_phy_postresume(phy);
}
EXPORT_SYMBOL_GPL(tegra_usb_phy_postresume);

-void tegra_ehci_phy_restore_start(struct usb_phy *x,
- enum tegra_usb_phy_port_speed port_speed)
+void tegra_ehci_phy_restore_start(struct usb_phy *u_phy,
+ enum tegra_usb_phy_port_speed port_speed)
{
- struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (!phy->is_ulpi_phy)
utmi_phy_restore_start(phy, port_speed);
}
EXPORT_SYMBOL_GPL(tegra_ehci_phy_restore_start);

-void tegra_ehci_phy_restore_end(struct usb_phy *x)
+void tegra_ehci_phy_restore_end(struct usb_phy *u_phy)
{
- struct tegra_usb_phy *phy = container_of(x, struct tegra_usb_phy, u_phy);
+ struct tegra_usb_phy *phy = to_tegra_usb_phy(u_phy);

if (!phy->is_ulpi_phy)
utmi_phy_restore_end(phy);
@@ -946,21 +972,25 @@ static int read_utmi_param(struct platform_device *pdev, const char *param,
u8 *dest)
{
u32 value;
- int err = of_property_read_u32(pdev->dev.of_node, param, &value);
- *dest = (u8)value;
- if (err < 0)
+ int err;
+
+ err = of_property_read_u32(pdev->dev.of_node, param, &value);
+ if (err)
dev_err(&pdev->dev,
"Failed to read USB UTMI parameter %s: %d\n",
param, err);
+ else
+ *dest = value;
+
return err;
}

static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,
struct platform_device *pdev)
{
+ struct tegra_utmip_config *config;
struct resource *res;
int err;
- struct tegra_utmip_config *config;

tegra_phy->is_ulpi_phy = false;

@@ -971,7 +1001,7 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,
}

tegra_phy->pad_regs = devm_ioremap(&pdev->dev, res->start,
- resource_size(res));
+ resource_size(res));
if (!tegra_phy->pad_regs) {
dev_err(&pdev->dev, "Failed to remap UTMI pad regs\n");
return -ENOMEM;
@@ -985,49 +1015,49 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,
config = tegra_phy->config;

err = read_utmi_param(pdev, "nvidia,hssync-start-delay",
- &config->hssync_start_delay);
- if (err < 0)
+ &config->hssync_start_delay);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,elastic-limit",
- &config->elastic_limit);
- if (err < 0)
+ &config->elastic_limit);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,idle-wait-delay",
- &config->idle_wait_delay);
- if (err < 0)
+ &config->idle_wait_delay);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,term-range-adj",
- &config->term_range_adj);
- if (err < 0)
+ &config->term_range_adj);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,xcvr-lsfslew",
- &config->xcvr_lsfslew);
- if (err < 0)
+ &config->xcvr_lsfslew);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,xcvr-lsrslew",
- &config->xcvr_lsrslew);
- if (err < 0)
+ &config->xcvr_lsrslew);
+ if (err)
return err;

if (tegra_phy->soc_config->requires_extra_tuning_parameters) {
err = read_utmi_param(pdev, "nvidia,xcvr-hsslew",
- &config->xcvr_hsslew);
- if (err < 0)
+ &config->xcvr_hsslew);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,hssquelch-level",
- &config->hssquelch_level);
- if (err < 0)
+ &config->hssquelch_level);
+ if (err)
return err;

err = read_utmi_param(pdev, "nvidia,hsdiscon-level",
- &config->hsdiscon_level);
- if (err < 0)
+ &config->hsdiscon_level);
+ if (err)
return err;
}

@@ -1036,8 +1066,8 @@ static int utmi_phy_probe(struct tegra_usb_phy *tegra_phy,

if (!config->xcvr_setup_use_fuses) {
err = read_utmi_param(pdev, "nvidia,xcvr-setup",
- &config->xcvr_setup);
- if (err < 0)
+ &config->xcvr_setup);
+ if (err)
return err;
}

@@ -1067,23 +1097,18 @@ MODULE_DEVICE_TABLE(of, tegra_usb_phy_id_table);

static int tegra_usb_phy_probe(struct platform_device *pdev)
{
- const struct of_device_id *match;
- struct resource *res;
- struct tegra_usb_phy *tegra_phy = NULL;
struct device_node *np = pdev->dev.of_node;
+ struct tegra_usb_phy *tegra_phy;
enum usb_phy_interface phy_type;
+ struct reset_control *reset;
+ struct resource *res;
int err;

tegra_phy = devm_kzalloc(&pdev->dev, sizeof(*tegra_phy), GFP_KERNEL);
if (!tegra_phy)
return -ENOMEM;

- match = of_match_device(tegra_usb_phy_id_table, &pdev->dev);
- if (!match) {
- dev_err(&pdev->dev, "Error: No device match found\n");
- return -ENODEV;
- }
- tegra_phy->soc_config = match->data;
+ tegra_phy->soc_config = of_device_get_match_data(&pdev->dev);

res = platform_get_resource(pdev, IORESOURCE_MEM, 0);
if (!res) {
@@ -1092,7 +1117,7 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
}

tegra_phy->regs = devm_ioremap(&pdev->dev, res->start,
- resource_size(res));
+ resource_size(res));
if (!tegra_phy->regs) {
dev_err(&pdev->dev, "Failed to remap I/O memory\n");
return -ENOMEM;
@@ -1101,33 +1126,6 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
tegra_phy->is_legacy_phy =
of_property_read_bool(np, "nvidia,has-legacy-mode");

- phy_type = of_usb_get_phy_mode(np);
- switch (phy_type) {
- case USBPHY_INTERFACE_MODE_UTMI:
- err = utmi_phy_probe(tegra_phy, pdev);
- if (err < 0)
- return err;
- break;
-
- case USBPHY_INTERFACE_MODE_ULPI:
- tegra_phy->is_ulpi_phy = true;
-
- tegra_phy->reset_gpio =
- of_get_named_gpio(np, "nvidia,phy-reset-gpio", 0);
- if (!gpio_is_valid(tegra_phy->reset_gpio)) {
- dev_err(&pdev->dev,
- "Invalid GPIO: %d\n", tegra_phy->reset_gpio);
- return tegra_phy->reset_gpio;
- }
- tegra_phy->config = NULL;
- break;
-
- default:
- dev_err(&pdev->dev, "phy_type %u is invalid or unsupported\n",
- phy_type);
- return -EINVAL;
- }
-
if (of_find_property(np, "dr_mode", NULL))
tegra_phy->mode = usb_get_dr_mode(&pdev->dev);
else
@@ -1155,7 +1153,44 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
return err;
}

- if (tegra_phy->is_ulpi_phy) {
+ phy_type = of_usb_get_phy_mode(np);
+ switch (phy_type) {
+ case USBPHY_INTERFACE_MODE_UTMI:
+ err = utmi_phy_probe(tegra_phy, pdev);
+ if (err)
+ return err;
+
+ tegra_phy->pad_clk = devm_clk_get(&pdev->dev, "utmi-pads");
+ err = PTR_ERR_OR_ZERO(tegra_phy->pad_clk);
+ if (err) {
+ dev_err(&pdev->dev,
+ "Failed to get UTMIP pad clock: %d\n", err);
+ return err;
+ }
+
+ reset = devm_reset_control_get_optional_shared(&pdev->dev,
+ "utmi-pads");
+ err = PTR_ERR_OR_ZERO(reset);
+ if (err) {
+ dev_err(&pdev->dev,
+ "Failed to get UTMI-pads reset: %d\n", err);
+ return err;
+ }
+ tegra_phy->pad_rst = reset;
+ break;
+
+ case USBPHY_INTERFACE_MODE_ULPI:
+ tegra_phy->is_ulpi_phy = true;
+
+ tegra_phy->reset_gpio =
+ of_get_named_gpio(np, "nvidia,phy-reset-gpio", 0);
+
+ if (!gpio_is_valid(tegra_phy->reset_gpio)) {
+ dev_err(&pdev->dev,
+ "Invalid GPIO: %d\n", tegra_phy->reset_gpio);
+ return tegra_phy->reset_gpio;
+ }
+
tegra_phy->clk = devm_clk_get(&pdev->dev, "ulpi-link");
err = PTR_ERR_OR_ZERO(tegra_phy->clk);
if (err) {
@@ -1165,8 +1200,8 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
}

err = devm_gpio_request(&pdev->dev, tegra_phy->reset_gpio,
- "ulpi_phy_reset_b");
- if (err < 0) {
+ "ulpi_phy_reset_b");
+ if (err) {
dev_err(&pdev->dev, "Request failed for GPIO %d: %d\n",
tegra_phy->reset_gpio, err);
return err;
@@ -1175,28 +1210,16 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
tegra_phy->ulpi = otg_ulpi_create(&ulpi_viewport_access_ops, 0);
if (!tegra_phy->ulpi) {
dev_err(&pdev->dev, "Failed to create ULPI OTG\n");
- err = -ENOMEM;
- return err;
+ return -ENOMEM;
}

tegra_phy->ulpi->io_priv = tegra_phy->regs + ULPI_VIEWPORT;
- } else {
- tegra_phy->pad_clk = devm_clk_get(&pdev->dev, "utmi-pads");
- err = PTR_ERR_OR_ZERO(tegra_phy->pad_clk);
- if (err) {
- dev_err(&pdev->dev,
- "Failed to get UTMIP pad clock: %d\n", err);
- return err;
- }
+ break;

- tegra_phy->pad_rst = devm_reset_control_get_optional_shared(
- &pdev->dev, "utmi-pads");
- err = PTR_ERR_OR_ZERO(tegra_phy->pad_rst);
- if (err) {
- dev_err(&pdev->dev,
- "Failed to get UTMI-pads reset: %d\n", err);
- return err;
- }
+ default:
+ dev_err(&pdev->dev, "phy_type %u is invalid or unsupported\n",
+ phy_type);
+ return -EINVAL;
}

tegra_phy->u_phy.dev = &pdev->dev;
@@ -1207,7 +1230,7 @@ static int tegra_usb_phy_probe(struct platform_device *pdev)
platform_set_drvdata(pdev, tegra_phy);

err = usb_add_phy_dev(&tegra_phy->u_phy);
- if (err < 0)
+ if (err)
goto free_ulpi;

return 0;
--
2.24.0