Re: [PATCH v3 4/5] dt-bindings: PCI: meson: Update PCIE bindings documentation

[Rob Herring]

On Tue, Dec 24, 2019 at 06:39:41PM +0100, Remi Pommarel wrote:
> Now that a new PHYs has been introduced for AXG SoC family, update
> dt bindings documentation.

This breaks compatibility. If that's okay, say so and why it is.

If only someone had said putting the phy here in the first place was 
wrong:

https://lore.kernel.org/linux-amlogic/20180829004122.GA25928@bogus/

> 
> Signed-off-by: Remi Pommarel <repk@xxxxxxxxxxxx>
> ---
>  .../bindings/pci/amlogic,meson-pcie.txt       | 22 ++++++++-----------
>  1 file changed, 9 insertions(+), 13 deletions(-)
> 
> diff --git a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> index 84fdc422792e..b6acbe694ffb 100644
> --- a/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> +++ b/Documentation/devicetree/bindings/pci/amlogic,meson-pcie.txt
> @@ -18,7 +18,6 @@ Required properties:
>  - reg-names: Must be
>  	- "elbi"	External local bus interface registers
>  	- "cfg"		Meson specific registers
> -	- "phy"		Meson PCIE PHY registers for AXG SoC Family
>  	- "config"	PCIe configuration space
>  - reset-gpios: The GPIO to generate PCIe PERST# assert and deassert signal.
>  - clocks: Must contain an entry for each entry in clock-names.
> @@ -26,13 +25,13 @@ Required properties:
>  	- "pclk"       PCIe GEN 100M PLL clock
>  	- "port"       PCIe_x(A or B) RC clock gate
>  	- "general"    PCIe Phy clock
> -	- "mipi"       PCIe_x(A or B) 100M ref clock gate for AXG SoC Family
>  - resets: phandle to the reset lines.
> -- reset-names: must contain "phy" "port" and "apb"
> -       - "phy"         Share PHY reset for AXG SoC Family
> +- reset-names: must contain "port" and "apb"
>         - "port"        Port A or B reset
>         - "apb"         Share APB reset
> -- phys: should contain a phandle to the shared phy for G12A SoC Family
> +- phys: should contain a phandle to the PCIE phy
> +- phy-names: must contain "pcie"
> +
>  - device_type:
>  	should be "pci". As specified in designware-pcie.txt
>  
> @@ -43,9 +42,8 @@ Example configuration:
>  			compatible = "amlogic,axg-pcie", "snps,dw-pcie";
>  			reg = <0x0 0xf9800000 0x0 0x400000
>  					0x0 0xff646000 0x0 0x2000
> -					0x0 0xff644000 0x0 0x2000
>  					0x0 0xf9f00000 0x0 0x100000>;
> -			reg-names = "elbi", "cfg", "phy", "config";
> +			reg-names = "elbi", "cfg", "config";
>  			reset-gpios = <&gpio GPIOX_19 GPIO_ACTIVE_HIGH>;
>  			interrupts = <GIC_SPI 177 IRQ_TYPE_EDGE_RISING>;
>  			#interrupt-cells = <1>;
> @@ -58,17 +56,15 @@ Example configuration:
>  			ranges = <0x82000000 0 0 0x0 0xf9c00000 0 0x00300000>;
>  
>  			clocks = <&clkc CLKID_USB
> -					&clkc CLKID_MIPI_ENABLE
>  					&clkc CLKID_PCIE_A
>  					&clkc CLKID_PCIE_CML_EN0>;
>  			clock-names = "general",
> -					"mipi",
>  					"pclk",
>  					"port";
> -			resets = <&reset RESET_PCIE_PHY>,
> -				<&reset RESET_PCIE_A>,
> +			resets = <&reset RESET_PCIE_A>,
>  				<&reset RESET_PCIE_APB>;
> -			reset-names = "phy",
> -					"port",
> +			reset-names = "port",
>  					"apb";
> +			phys = <&pcie_phy>;
> +			phy-names = "pcie";
>  	};
> -- 
> 2.24.0
>