Re: [PATCH v2 03/11] DTS: ARM: pandora-common: define wl1251 as child node of mmc3

[Ulf Hansson]

On Sat, 19 Oct 2019 at 20:42, H. Nikolaus Schaller <hns@xxxxxxxxxxxxx> wrote:
>
> Since v4.7 the dma initialization requires that there is a
> device tree property for "rx" and "tx" channels which is
> not provided by the pdata-quirks initialization.
>
> By conversion of the mmc3 setup to device tree this will
> finally allows to remove the OpenPandora wlan specific omap3
> data-quirks.
>
> Fixes: 81eef6ca9201 ("mmc: omap_hsmmc: Use dma_request_chan() for requesting DMA channel")
>
> Signed-off-by: H. Nikolaus Schaller <hns@xxxxxxxxxxxxx>
> Cc: <stable@xxxxxxxxxxxxxxx> # 4.7.0
> ---
>  arch/arm/boot/dts/omap3-pandora-common.dtsi | 37 +++++++++++++++++++--
>  1 file changed, 35 insertions(+), 2 deletions(-)
>
> diff --git a/arch/arm/boot/dts/omap3-pandora-common.dtsi b/arch/arm/boot/dts/omap3-pandora-common.dtsi
> index ec5891718ae6..c595b3eb314d 100644
> --- a/arch/arm/boot/dts/omap3-pandora-common.dtsi
> +++ b/arch/arm/boot/dts/omap3-pandora-common.dtsi
> @@ -226,6 +226,18 @@
>                 gpio = <&gpio6 4 GPIO_ACTIVE_HIGH>;     /* GPIO_164 */
>         };
>
> +       /* wl1251 wifi+bt module */
> +       wlan_en: fixed-regulator-wg7210_en {
> +               compatible = "regulator-fixed";
> +               regulator-name = "vwlan";
> +               regulator-min-microvolt = <1800000>;
> +               regulator-max-microvolt = <1800000>;

I doubt these are correct.

I guess this should be in the range of 2.7V-3.6V.

> +               startup-delay-us = <50000>;
> +               regulator-always-on;

Always on?

> +               enable-active-high;
> +               gpio = <&gpio1 23 GPIO_ACTIVE_HIGH>;
> +       };
> +
>         /* wg7210 (wifi+bt module) 32k clock buffer */
>         wg7210_32k: fixed-regulator-wg7210_32k {
>                 compatible = "regulator-fixed";
> @@ -522,9 +534,30 @@
>         /*wp-gpios = <&gpio4 31 GPIO_ACTIVE_HIGH>;*/    /* GPIO_127 */
>  };
>
> -/* mmc3 is probed using pdata-quirks to pass wl1251 card data */
>  &mmc3 {
> -       status = "disabled";
> +       vmmc-supply = <&wlan_en>;
> +
> +       bus-width = <4>;
> +       non-removable;
> +       ti,non-removable;
> +       cap-power-off-card;
> +
> +       pinctrl-names = "default";
> +       pinctrl-0 = <&mmc3_pins>;
> +
> +       #address-cells = <1>;
> +       #size-cells = <0>;
> +
> +       wlan: wl1251@1 {
> +               compatible = "ti,wl1251";
> +
> +               reg = <1>;
> +
> +               interrupt-parent = <&gpio1>;
> +               interrupts = <21 IRQ_TYPE_LEVEL_HIGH>;  /* GPIO_21 */
> +
> +               ti,wl1251-has-eeprom;
> +       };
>  };
>
>  /* bluetooth*/
> --
> 2.19.1
>

Kind regards
Uffe