Re: [PATCH 2/2] usb: core: Attempt power cycle when port is in eSS.Disabled state

[Kai-Heng Feng]

> On Oct 8, 2019, at 02:28, Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx> wrote:
> 
> On Dell TB16, Realtek USB ethernet (r8152) connects to an SMSC hub which
> then connects to ASMedia xHCI's root hub:
> 
> /:  Bus 04.Port 1: Dev 1, Class=root_hub, Driver=xhci_hcd/2p, 5000M
>    |__ Port 1: Dev 2, If 0, Class=Hub, Driver=hub/7p, 5000M
>            |__ Port 2: Dev 3, If 0, Class=Vendor Specific Class, Driver=r8152, 5000M
> 
> Bus 004 Device 001: ID 1d6b:0003 Linux Foundation 3.0 root hub
> Bus 004 Device 002: ID 0424:5537 Standard Microsystems Corp. USB5537B
> Bus 004 Device 003: ID 0bda:8153 Realtek Semiconductor Corp. RTL8153 Gigabit Ethernet Adapter
> 
> The SMSC hub may disconnect after system resume from suspend. When this
> happens, the reset resume attempt fails, and the last resort to disable
> the port and see something comes up later, also fails.
> 
> When the issue occurs, the link state stays in eSS.Disabled state
> despite the warm reset attempts. The USB spec mentioned this can be
> caused by invalid VBus, and after some expiremets, it does show that the
> SMSC hub can be brought back after a power cycle.
> 
> So let's power cycle the port at the end of reset resume attempt, if
> it's in eSS.Disabled state.

Is there any suggestion to make this series get merged?

Kai-Heng

> 
> Signed-off-by: Kai-Heng Feng <kai.heng.feng@xxxxxxxxxxxxx>
> ---
> drivers/usb/core/hub.c | 21 +++++++++++++++++++--
> 1 file changed, 19 insertions(+), 2 deletions(-)
> 
> diff --git a/drivers/usb/core/hub.c b/drivers/usb/core/hub.c
> index 6655a6a1651b..5f50aca7cf67 100644
> --- a/drivers/usb/core/hub.c
> +++ b/drivers/usb/core/hub.c
> @@ -2739,20 +2739,33 @@ static bool hub_port_warm_reset_required(struct usb_hub *hub, int port1,
> 		|| link_state == USB_SS_PORT_LS_COMP_MOD;
> }
> 
> +static bool hub_port_power_cycle_required(struct usb_hub *hub, int port1,
> +		u16 portstatus)
> +{
> +	u16 link_state;
> +
> +	if (!hub_is_superspeed(hub->hdev))
> +		return false;
> +
> +	link_state = portstatus & USB_PORT_STAT_LINK_STATE;
> +	return link_state == USB_SS_PORT_LS_SS_DISABLED;
> +}
> +
> static void hub_port_power_cycle(struct usb_hub *hub, int port1)
> {
> +	struct usb_port *port_dev = hub->ports[port1  - 1];
> 	int ret;
> 
> 	ret = usb_hub_set_port_power(hub, port1, false);
> 	if (ret) {
> -		dev_info(&udev->dev, "failed to disable port power\n");
> +		dev_info(&port_dev->dev, "failed to disable port power\n");
> 		return;
> 	}
> 
> 	msleep(2 * hub_power_on_good_delay(hub));
> 	ret = usb_hub_set_port_power(hub, port1, true);
> 	if (ret) {
> -		dev_info(&udev->dev, "failed to enable port power\n");
> +		dev_info(&port_dev->dev, "failed to enable port power\n");
> 		return;
> 	}
> 
> @@ -3600,6 +3613,10 @@ int usb_port_resume(struct usb_device *udev, pm_message_t msg)
> 	if (status < 0) {
> 		dev_dbg(&udev->dev, "can't resume, status %d\n", status);
> 		hub_port_logical_disconnect(hub, port1);
> +		if (hub_port_power_cycle_required(hub, port1, portstatus)) {
> +			dev_info(&udev->dev, "device in disabled state, attempt power cycle\n");
> +			hub_port_power_cycle(hub, port1);
> +		}
> 	} else  {
> 		/* Try to enable USB2 hardware LPM */
> 		usb_enable_usb2_hardware_lpm(udev);
> -- 
> 2.17.1
>