Re: [PATCH 2/2] PCI: dwc: Add support to handle ZRX-DC Compliant PHYs

From: Andrew Murray
Date: Mon Oct 21 2019 - 10:17:51 EST


On Mon, Oct 21, 2019 at 07:44:25PM +0530, Pankaj Dubey wrote:
>
>
> > -----Original Message-----
> > From: Andrew Murray <andrew.murray@xxxxxxx>
> > Sent: Monday, October 21, 2019 7:34 PM
> > To: Anvesh Salveru <anvesh.s@xxxxxxxxxxx>
> > Cc: linux-pci@xxxxxxxxxxxxxxx; linux-kernel@xxxxxxxxxxxxxxx;
> > bhelgaas@xxxxxxxxxx; gustavo.pimentel@xxxxxxxxxxxx;
> > jingoohan1@xxxxxxxxx; lorenzo.pieralisi@xxxxxxx; Pankaj Dubey
> > <pankaj.dubey@xxxxxxxxxxx>
> > Subject: Re: [PATCH 2/2] PCI: dwc: Add support to handle ZRX-DC Compliant
> > PHYs
> >
> > On Mon, Oct 21, 2019 at 05:59:53PM +0530, Anvesh Salveru wrote:
> > > Many platforms use DesignWare controller but the PHY can be different
> > > in different platforms. If the PHY is compliant is to ZRX-DC
> > > specification
> >
> > s/is to/to the/
>
> OK
>
> >
> > > it helps in low power consumption during power states.
> >
> > s/in low/lower/
> >
> OK
> > >
> > > If current data rate is 8.0 GT/s or higher and PHY is not compliant to
> > > ZRX-DC specification, then after every 100ms link should transition to
> > > recovery state during the low power states.
> > >
> > > DesignWare controller provides GEN3_ZRXDC_NONCOMPL field in
> > > GEN3_RELATED_OFF to specify about ZRX-DC compliant PHY.
> > >
> > > Platforms with ZRX-DC compliant PHY can set "snps,phy-zrxdc-compliant"
> > > property in controller DT node to specify this property to the
> controller.
> > >
> > > Signed-off-by: Anvesh Salveru <anvesh.s@xxxxxxxxxxx>
> > > Signed-off-by: Pankaj Dubey <pankaj.dubey@xxxxxxxxxxx>
> > > ---
> > > drivers/pci/controller/dwc/pcie-designware.c | 7 +++++++
> > > drivers/pci/controller/dwc/pcie-designware.h | 3 +++
> > > 2 files changed, 10 insertions(+)
> > >
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.c
> > > b/drivers/pci/controller/dwc/pcie-designware.c
> > > index 820488dfeaed..6560d9f765d7 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.c
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.c
> > > @@ -556,4 +556,11 @@ void dw_pcie_setup(struct dw_pcie *pci)
> > > PCIE_PL_CHK_REG_CHK_REG_START;
> > > dw_pcie_writel_dbi(pci, PCIE_PL_CHK_REG_CONTROL_STATUS,
> > val);
> > > }
> > > +
> > > + if (of_property_read_bool(np, "snps,phy-zrxdc-compliant")) {
> > > + val = dw_pcie_readl_dbi(pci, PCIE_PORT_GEN3_RELATED);
> > > + val &= ~PORT_LOGIC_GEN3_ZRXDC_NONCOMPL;
> > > + dw_pcie_writel_dbi(pci, PCIE_PORT_GEN3_RELATED, val);
> > > + }
> > > +
> >
> > Given that this duplicates tegra_pcie_prepare_host in pcie-tegra194.c, can
> we
> > update that driver to adopt this new binding?
> >
>
> Yes, Thanks for highlighting this. Otherwise I was worried that we have one
> more patch without real user :)

Indeed :|

Though besides Tegra, is there any other reason you are adding this?

> We will update pcie-tegra194.c driver and post the patch to adopt this
> binding.

It's much appreciated.

Andrew Murray

>
> > Thanks,
> >
> > Andrew Murray
> >
> > > }
> > > diff --git a/drivers/pci/controller/dwc/pcie-designware.h
> > > b/drivers/pci/controller/dwc/pcie-designware.h
> > > index 5a18e94e52c8..427a55ec43c6 100644
> > > --- a/drivers/pci/controller/dwc/pcie-designware.h
> > > +++ b/drivers/pci/controller/dwc/pcie-designware.h
> > > @@ -60,6 +60,9 @@
> > > #define PCIE_MSI_INTR0_MASK 0x82C
> > > #define PCIE_MSI_INTR0_STATUS 0x830
> > >
> > > +#define PCIE_PORT_GEN3_RELATED 0x890
> > > +#define PORT_LOGIC_GEN3_ZRXDC_NONCOMPL BIT(0)
> > > +
> > > #define PCIE_ATU_VIEWPORT 0x900
> > > #define PCIE_ATU_REGION_INBOUND BIT(31)
> > > #define PCIE_ATU_REGION_OUTBOUND 0
> > > --
> > > 2.17.1
> > >
>