Re: [RFC][PATCH v2 4/5] dt-bindings: usb: dwc3: of-simple: add compatible for HiSi

From: Rob Herring
Date: Mon Oct 07 2019 - 14:38:36 EST


On Mon, Oct 7, 2019 at 12:56 PM John Stultz <john.stultz@xxxxxxxxxx> wrote:
>
> Add necessary compatible flag for HiSi's DWC3 so
> dwc3-of-simple will probe.
>
> Cc: Greg Kroah-Hartman <gregkh@xxxxxxxxxxxxxxxxxxx>
> Cc: Felipe Balbi <balbi@xxxxxxxxxx>
> Cc: Andy Shevchenko <andy.shevchenko@xxxxxxxxx>
> Cc: Rob Herring <robh+dt@xxxxxxxxxx>
> Cc: Mark Rutland <mark.rutland@xxxxxxx>
> Cc: Yu Chen <chenyu56@xxxxxxxxxx>
> Cc: Matthias Brugger <matthias.bgg@xxxxxxxxx>
> Cc: Chunfeng Yun <chunfeng.yun@xxxxxxxxxxxx>
> Cc: linux-usb@xxxxxxxxxxxxxxx
> Cc: devicetree@xxxxxxxxxxxxxxx
> Signed-off-by: John Stultz <john.stultz@xxxxxxxxxx>
> ---
> v2: Tweaked clock names as clk_usb3phy_ref didn't seem right.
> ---
> .../devicetree/bindings/usb/hisi,dwc3.txt | 52 +++++++++++++++++++
> 1 file changed, 52 insertions(+)
> create mode 100644 Documentation/devicetree/bindings/usb/hisi,dwc3.txt

Can you make this a schema.

> diff --git a/Documentation/devicetree/bindings/usb/hisi,dwc3.txt b/Documentation/devicetree/bindings/usb/hisi,dwc3.txt
> new file mode 100644
> index 000000000000..3a3e5c320f2a
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/usb/hisi,dwc3.txt
> @@ -0,0 +1,52 @@
> +HiSi SuperSpeed DWC3 USB SoC controller
> +
> +Required properties:
> +- compatible: should contain "hisilicon,hi3660-dwc3" for HiSi SoC
> +- clocks: A list of phandle + clock-specifier pairs for the
> + clocks listed in clock-names
> +- clock-names: Should contain the following:
> + "clk_abb_usb" USB reference clk
> + "aclk_usb3otg" USB3 OTG aclk
> +
> +- assigned-clocks: Should be:
> + HI3660_ACLK_GATE_USB3OTG
> +- assigned-clock-rates: Should be:
> + 229Mhz (229000000) for HI3660_ACLK_GATE_USB3OTG
> +
> +Optional properties:
> +- resets: Phandle to reset control that resets core and wrapper.

Looks like 4 resets though.

> +
> +Required child node:
> +A child node must exist to represent the core DWC3 IP block. The name of
> +the node is not important. The content of the node is defined in dwc3.txt.
> +
> +Example device nodes:
> +
> + usb3: hisi_dwc3 {
> + compatible = "hisilicon,hi3660-dwc3";
> + #address-cells = <2>;
> + #size-cells = <2>;
> + ranges;
> +
> + clocks = <&crg_ctrl HI3660_CLK_ABB_USB>,
> + <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
> + clock-names = "clk_abb_usb", "aclk_usb3otg";
> +
> + assigned-clocks = <&crg_ctrl HI3660_ACLK_GATE_USB3OTG>;
> + assigned-clock-rates = <229 000 000>;
> + resets = <&crg_rst 0x90 8>,
> + <&crg_rst 0x90 7>,
> + <&crg_rst 0x90 6>,
> + <&crg_rst 0x90 5>;
> +
> + dwc3: dwc3@ff100000 {

If it's only clocks and resets for the wrapper node, just make this
all one node.

And 'usb3' for the node name.

> + compatible = "snps,dwc3";
> + reg = <0x0 0xff100000 0x0 0x100000>;
> + interrupts = <0 159 4>, <0 161 4>;
> + phys = <&usb_phy>;
> + phy-names = "usb3-phy";
> + dr_mode = "otg";
> +
> + ...
> + };
> + };
> --
> 2.17.1
>