Re: [v1] e1000e: EEH on e1000e adapter detects io perm failure can trigger crash

From: David Z. Dai
Date: Thu Oct 03 2019 - 14:51:07 EST


On Thu, 2019-10-03 at 10:39 -0700, Alexander Duyck wrote:
> On Thu, Oct 3, 2019 at 9:59 AM David Dai <zdai@xxxxxxxxxxxxxxxxxx> wrote:
> >
> > We see the behavior when EEH e1000e adapter detects io permanent failure,
> > it will crash kernel with this stack:
> > EEH: Beginning: 'error_detected(permanent failure)'
> > EEH: PE#900000 (PCI 0115:90:00.1): Invoking e1000e->error_detected(permanent failure)
> > EEH: PE#900000 (PCI 0115:90:00.1): e1000e driver reports: 'disconnect'
> > EEH: PE#900000 (PCI 0115:90:00.0): Invoking e1000e->error_detected(permanent failure)
> > EEH: PE#900000 (PCI 0115:90:00.0): e1000e driver reports: 'disconnect'
> > EEH: Finished:'error_detected(permanent failure)'
> > Oops: Exception in kernel mode, sig: 5 [#1]
> > NIP [c0000000007b1be0] free_msi_irqs+0xa0/0x280
> > LR [c0000000007b1bd0] free_msi_irqs+0x90/0x280
> > Call Trace:
> > [c0000004f491ba10] [c0000000007b1bd0] free_msi_irqs+0x90/0x280 (unreliable)
> > [c0000004f491ba70] [c0000000007b260c] pci_disable_msi+0x13c/0x180
> > [c0000004f491bab0] [d0000000046381ac] e1000_remove+0x234/0x2a0 [e1000e]
> > [c0000004f491baf0] [c000000000783cec] pci_device_remove+0x6c/0x120
> > [c0000004f491bb30] [c00000000088da6c] device_release_driver_internal+0x2bc/0x3f0
> > [c0000004f491bb80] [c00000000076f5a8] pci_stop_and_remove_bus_device+0xb8/0x110
> > [c0000004f491bbc0] [c00000000006e890] pci_hp_remove_devices+0x90/0x130
> > [c0000004f491bc50] [c00000000004ad34] eeh_handle_normal_event+0x1d4/0x660
> > [c0000004f491bd10] [c00000000004bf10] eeh_event_handler+0x1c0/0x1e0
> > [c0000004f491bdc0] [c00000000017c4ac] kthread+0x1ac/0x1c0
> > [c0000004f491be30] [c00000000000b75c] ret_from_kernel_thread+0x5c/0x80
> >
> > Basically the e1000e irqs haven't been freed at the time eeh is trying to
> > remove the the e1000e device.
> > Need to make sure when e1000e_close is called to bring down the NIC,
> > if adapter error_state is pci_channel_io_perm_failure, it should also
> > bring down the link and free irqs.
> >
> > Reported-by: Morumuri Srivalli <smorumu1@xxxxxxxxxx>
> > Signed-off-by: David Dai <zdai@xxxxxxxxxxxxxxxxxx>
> > ---
> > drivers/net/ethernet/intel/e1000e/netdev.c | 3 ++-
> > 1 files changed, 2 insertions(+), 1 deletions(-)
> >
> > diff --git a/drivers/net/ethernet/intel/e1000e/netdev.c b/drivers/net/ethernet/intel/e1000e/netdev.c
> > index d7d56e4..cf618e1 100644
> > --- a/drivers/net/ethernet/intel/e1000e/netdev.c
> > +++ b/drivers/net/ethernet/intel/e1000e/netdev.c
> > @@ -4715,7 +4715,8 @@ int e1000e_close(struct net_device *netdev)
> >
> > pm_runtime_get_sync(&pdev->dev);
> >
> > - if (!test_bit(__E1000_DOWN, &adapter->state)) {
> > + if (!test_bit(__E1000_DOWN, &adapter->state) ||
> > + (adapter->pdev->error_state == pci_channel_io_perm_failure)) {
> > e1000e_down(adapter, true);
> > e1000_free_irq(adapter);
>
> It seems like the issue is the fact that e1000_io_error_detected is
> calling e1000e_down without the e1000_free_irq() bit. Instead of doing
> this couldn't you simply add the following to e1000_is_slot_reset in
> the "result = PCI_ERS_RESULT_DISCONNECT" case:
> if (netif_running(netdev)
> e1000_free_irq(adapter);
>
> Alternatively we could look at freeing and reallocating the IRQs in
> the event of an error like we do for the e1000e_pm_freeze and
> e1000e_pm_thaw cases. That might make more sense since we are dealing
> with an error we might want to free and reallocate the IRQ resources
> assigned to the device.
>
> Thanks.
>
> - Alex

Thanks for the quick reply and comment!
Looked the e1000_io_slot_reset() routine:
err = pci_enable_device_mem(pdev);
if (err) {
dev_err(&pdev->dev,
"Cannot re-enable PCI device after reset.\n");
result = PCI_ERS_RESULT_DISCONNECT;
} else {
I didn't see log message "Cannot re-enable PCI device after reset" at
the time of crash.

I can still apply the same logic in e1000_io_error_detected() routine:
if (state == pci_channel_io_perm_failure) {
+ if (netif_running(netdev))
+ e1000_free_irq(adapter);
return PCI_ERS_RESULT_DISCONNECT;
}
Will test this once the test hardware is available again.

Thanks! - David