Re: [PATCH v9 20/22] soc/tegra: pmc: Configure deep sleep control settings

[Dmitry Osipenko]

16.08.2019 22:42, Sowjanya Komatineni ÐÐÑÐÑ:
> Tegra210 and prior Tegra chips have deep sleep entry and wakeup related
> timings which are platform specific that should be configured before
> entering into deep sleep.
> 
> Below are the timing specific configurations for deep sleep entry and
> wakeup.
> - Core rail power-on stabilization timer
> - OSC clock stabilization timer after SOC rail power is stabilized.
> - Core power off time is the minimum wake delay to keep the system
>   in deep sleep state irrespective of any quick wake event.
> 
> These values depends on the discharge time of regulators and turn OFF
> time of the PMIC to allow the complete system to finish entering into
> deep sleep state.
> 
> These values vary based on the platform design and are specified
> through the device tree.
> 
> This patch has implementation to configure these timings which are must
> to have for proper deep sleep and wakeup operations.
> 
> Signed-off-by: Sowjanya Komatineni <skomatineni@xxxxxxxxxx>
> ---
>  drivers/soc/tegra/pmc.c | 14 +++++++++++++-
>  1 file changed, 13 insertions(+), 1 deletion(-)
> 
> diff --git a/drivers/soc/tegra/pmc.c b/drivers/soc/tegra/pmc.c
> index 53ed70773872..710969043668 100644
> --- a/drivers/soc/tegra/pmc.c
> +++ b/drivers/soc/tegra/pmc.c
> @@ -88,6 +88,8 @@
>  
>  #define PMC_CPUPWRGOOD_TIMER		0xc8
>  #define PMC_CPUPWROFF_TIMER		0xcc
> +#define PMC_COREPWRGOOD_TIMER		0x3c
> +#define PMC_COREPWROFF_TIMER		0xe0
>  
>  #define PMC_PWR_DET_VALUE		0xe4
>  
> @@ -2277,7 +2279,7 @@ static const struct tegra_pmc_regs tegra20_pmc_regs = {
>  
>  static void tegra20_pmc_init(struct tegra_pmc *pmc)
>  {
> -	u32 value;
> +	u32 value, osc, pmu, off;
>  
>  	/* Always enable CPU power request */
>  	value = tegra_pmc_readl(pmc, PMC_CNTRL);
> @@ -2303,6 +2305,16 @@ static void tegra20_pmc_init(struct tegra_pmc *pmc)
>  	value = tegra_pmc_readl(pmc, PMC_CNTRL);
>  	value |= PMC_CNTRL_SYSCLK_OE;
>  	tegra_pmc_writel(pmc, value, PMC_CNTRL);
> +
> +	/* program core timings which are applicable only for suspend state */
> +	if (pmc->suspend_mode != TEGRA_SUSPEND_NONE) {
> +		osc = DIV_ROUND_UP(pmc->core_osc_time * 8192, 1000000);
> +		pmu = DIV_ROUND_UP(pmc->core_pmu_time * 32768, 1000000);
> +		off = DIV_ROUND_UP(pmc->core_off_time * 32768, 1000000);
> +		tegra_pmc_writel(pmc, ((osc << 8) & 0xff00) | (pmu & 0xff),
> +				 PMC_COREPWRGOOD_TIMER);
> +		tegra_pmc_writel(pmc, off, PMC_COREPWROFF_TIMER);
> +	}
>  }
>  
>  static void tegra20_pmc_setup_irq_polarity(struct tegra_pmc *pmc,
> 

In the previous version of this patch there were checks for zero values
of the timers with intention to skip programming of the timers if value
is zero. I'm a bit puzzled by the new version, given that SUSPEND_NONE
means that suspending isn't available at all and thus PMC timers won't
be utilized, hence it shouldn't matter what values are programmed for
the counters, isn't it?