Re: [PATCH 03/16] net: phy: adin: add support for interrupts

[Ardelean, Alexandru]

On Mon, 2019-08-05 at 16:21 +0200, Andrew Lunn wrote:
> [External]
> 
> On Mon, Aug 05, 2019 at 07:54:40PM +0300, Alexandru Ardelean wrote:
> > This change adds support for enabling PHY interrupts that can be used by
> > the PHY framework to get signal for link/speed/auto-negotiation changes.
> > 
> > Signed-off-by: Alexandru Ardelean <alexandru.ardelean@xxxxxxxxxx>
> > ---
> >  drivers/net/phy/adin.c | 44 ++++++++++++++++++++++++++++++++++++++++++
> >  1 file changed, 44 insertions(+)
> > 
> > diff --git a/drivers/net/phy/adin.c b/drivers/net/phy/adin.c
> > index c100a0dd95cd..b75c723bda79 100644
> > --- a/drivers/net/phy/adin.c
> > +++ b/drivers/net/phy/adin.c
> > @@ -14,6 +14,22 @@
> >  #define PHY_ID_ADIN1200				0x0283bc20
> >  #define PHY_ID_ADIN1300				0x0283bc30
> >  
> > +#define ADIN1300_INT_MASK_REG			0x0018
> > +#define   ADIN1300_INT_MDIO_SYNC_EN		BIT(9)
> > +#define   ADIN1300_INT_ANEG_STAT_CHNG_EN	BIT(8)
> > +#define   ADIN1300_INT_ANEG_PAGE_RX_EN		BIT(6)
> > +#define   ADIN1300_INT_IDLE_ERR_CNT_EN		BIT(5)
> > +#define   ADIN1300_INT_MAC_FIFO_OU_EN		BIT(4)
> > +#define   ADIN1300_INT_RX_STAT_CHNG_EN		BIT(3)
> > +#define   ADIN1300_INT_LINK_STAT_CHNG_EN	BIT(2)
> > +#define   ADIN1300_INT_SPEED_CHNG_EN		BIT(1)
> > +#define   ADIN1300_INT_HW_IRQ_EN		BIT(0)
> > +#define ADIN1300_INT_MASK_EN	\
> > +	(ADIN1300_INT_ANEG_STAT_CHNG_EN | ADIN1300_INT_ANEG_PAGE_RX_EN | \
> > +	 ADIN1300_INT_LINK_STAT_CHNG_EN | ADIN1300_INT_SPEED_CHNG_EN | \
> > +	 ADIN1300_INT_HW_IRQ_EN)
> > +#define ADIN1300_INT_STATUS_REG			0x0019
> > +
> >  static int adin_config_init(struct phy_device *phydev)
> >  {
> >  	int rc;
> > @@ -25,15 +41,40 @@ static int adin_config_init(struct phy_device *phydev)
> >  	return 0;
> >  }
> >  
> > +static int adin_phy_ack_intr(struct phy_device *phydev)
> > +{
> > +	int ret;
> > +
> > +	/* Clear pending interrupts.  */
> > +	ret = phy_read(phydev, ADIN1300_INT_STATUS_REG);
> > +	if (ret < 0)
> > +		return ret;
> > +
> > +	return 0;
> 
> Please go through the whole driver and throw out all the needless

ack;
i'll re-visit;

> 
> 	if (ret < 0)
> 		return ret;
> 
> 	return 0;
> 
> Thanks
> 	Andrew