Re: [PATCH net-next 3/3] net: stmmac: Introducing support for Page Pool

[Jon Hunter]

On 24/07/2019 11:04, Jose Abreu wrote:

...

> Jon, I was able to replicate (at some level) your setup:
> 
> # dmesg | grep -i arm-smmu
> [    1.337322] arm-smmu 70040000.iommu: probing hardware 
> configuration...
> [    1.337330] arm-smmu 70040000.iommu: SMMUv2 with:
> [    1.337338] arm-smmu 70040000.iommu:         stage 1 translation
> [    1.337346] arm-smmu 70040000.iommu:         stage 2 translation
> [    1.337354] arm-smmu 70040000.iommu:         nested translation
> [    1.337363] arm-smmu 70040000.iommu:         stream matching with 128 
> register groups
> [    1.337374] arm-smmu 70040000.iommu:         1 context banks (0 
> stage-2 only)
> [    1.337383] arm-smmu 70040000.iommu:         Supported page sizes: 
> 0x61311000
> [    1.337393] arm-smmu 70040000.iommu:         Stage-1: 48-bit VA -> 
> 48-bit IPA
> [    1.337402] arm-smmu 70040000.iommu:         Stage-2: 48-bit IPA -> 
> 48-bit PA
> 
> # dmesg | grep -i stmmac
> [    1.344106] stmmaceth 70000000.ethernet: Adding to iommu group 0
> [    1.344233] stmmaceth 70000000.ethernet: no reset control found
> [    1.348276] stmmaceth 70000000.ethernet: User ID: 0x10, Synopsys ID: 
> 0x51
> [    1.348285] stmmaceth 70000000.ethernet:     DWMAC4/5
> [    1.348293] stmmaceth 70000000.ethernet: DMA HW capability register 
> supported
> [    1.348302] stmmaceth 70000000.ethernet: RX Checksum Offload Engine 
> supported
> [    1.348311] stmmaceth 70000000.ethernet: TX Checksum insertion 
> supported
> [    1.348320] stmmaceth 70000000.ethernet: TSO supported
> [    1.348328] stmmaceth 70000000.ethernet: Enable RX Mitigation via HW 
> Watchdog Timer
> [    1.348337] stmmaceth 70000000.ethernet: TSO feature enabled
> [    1.348409] libphy: stmmac: probed
> [ 4159.140990] stmmaceth 70000000.ethernet eth0: PHY [stmmac-0:01] 
> driver [Generic PHY]
> [ 4159.141005] stmmaceth 70000000.ethernet eth0: phy: setting supported 
> 00,00000000,000062ff advertising 00,00000000,000062ff
> [ 4159.142359] stmmaceth 70000000.ethernet eth0: No Safety Features 
> support found
> [ 4159.142369] stmmaceth 70000000.ethernet eth0: IEEE 1588-2008 Advanced 
> Timestamp supported
> [ 4159.142429] stmmaceth 70000000.ethernet eth0: registered PTP clock
> [ 4159.142439] stmmaceth 70000000.ethernet eth0: configuring for 
> phy/gmii link mode
> [ 4159.142452] stmmaceth 70000000.ethernet eth0: phylink_mac_config: 
> mode=phy/gmii/Unknown/Unknown adv=00,00000000,000062ff pause=10 link=0 
> an=1
> [ 4159.142466] stmmaceth 70000000.ethernet eth0: phy link up 
> gmii/1Gbps/Full
> [ 4159.142475] stmmaceth 70000000.ethernet eth0: phylink_mac_config: 
> mode=phy/gmii/1Gbps/Full adv=00,00000000,00000000 pause=0f link=1 an=0
> [ 4159.142481] stmmaceth 70000000.ethernet eth0: Link is Up - 1Gbps/Full 
> - flow control rx/tx
> 
> The only missing point is the NFS boot that I can't replicate with this 
> setup. But I did some sanity checks:
> 
> Remote Enpoint:
> # dd if=/dev/urandom of=output.dat bs=128M count=1
> # nc -c 192.168.0.2 1234 < output.dat
> # md5sum output.dat 
> fde9e0818281836e4fc0edfede2b8762  output.dat
> 
> DUT:
> # nc -l -c -p 1234 > output.dat
> # md5sum output.dat 
> fde9e0818281836e4fc0edfede2b8762  output.dat

On my setup, if I do not use NFS to mount the rootfs, but then manually
mount the NFS share after booting, I do not see any problems reading or
writing to files on the share. So I am not sure if it is some sort of
race that is occurring when mounting the NFS share on boot. It is 100%
reproducible when using NFS for the root file-system.

I am using the Jetson TX2 devkit [0] to test this.

Cheers
Jon

[0] https://developer.nvidia.com/embedded/jetson-tx2-developer-kit

-- 
nvpublic