[PATCH v1 6/6] ASoC: sgtl5000: Improve VAG power and mute control

[Oleksandr Suvorov]

Change VAG power on/off control according to the following algorithm:
- turn VAG power ON on the 1st incoming event.
- keep it ON if there is any active VAG consumer (ADC/DAC/HP/Line-In).
- turn VAG power OFF when there is the latest consumer's pre-down event
  come.
- always delay after VAG power OFF to avoid pop.
- delay after VAG power ON if the initiative consumer is Line-In, this
  prevents pop during line-in muxing.

Also, according to the manual, to avoid any pops/clicks,
the outputs should be muted during input/output
routing changes.

Signed-off-by: Oleksandr Suvorov <oleksandr.suvorov@xxxxxxxxxxx>
---

 sound/soc/codecs/sgtl5000.c | 227 +++++++++++++++++++++++++++++++-----
 1 file changed, 195 insertions(+), 32 deletions(-)

diff --git sound/soc/codecs/sgtl5000.c sound/soc/codecs/sgtl5000.c
index ee1e4bf61322..acfbd5cdf936 100644
--- sound/soc/codecs/sgtl5000.c
+++ sound/soc/codecs/sgtl5000.c
@@ -31,6 +31,13 @@
 #define SGTL5000_DAP_REG_OFFSET	0x0100
 #define SGTL5000_MAX_REG_OFFSET	0x013A
 
+/* Delay for the VAG ramp up */
+#define SGTL5000_VAG_POWERUP_DELAY 500 /* ms */
+/* Delay for the VAG ramp down */
+#define SGTL5000_VAG_POWERDOWN_DELAY 500 /* ms */
+
+#define SGTL5000_OUTPUTS_MUTE (SGTL5000_HP_MUTE | SGTL5000_LINE_OUT_MUTE)
+
 /* default value of sgtl5000 registers */
 static const struct reg_default sgtl5000_reg_defaults[] = {
 	{ SGTL5000_CHIP_DIG_POWER,		0x0000 },
@@ -123,6 +130,18 @@ enum  {
 	I2S_SCLK_STRENGTH_HIGH,
 };
 
+enum {
+	HP_POWER_EVENT,
+	DAC_POWER_EVENT,
+	ADC_POWER_EVENT
+};
+
+struct sgtl5000_mute_state {
+	u16 hp_event;
+	u16 dac_event;
+	u16 adc_event;
+};
+
 /* sgtl5000 private structure in codec */
 struct sgtl5000_priv {
 	int sysclk;	/* sysclk rate */
@@ -137,8 +156,109 @@ struct sgtl5000_priv {
 	u8 micbias_voltage;
 	u8 lrclk_strength;
 	u8 sclk_strength;
+	struct sgtl5000_mute_state mute_state;
 };
 
+static inline int hp_sel_input(struct snd_soc_component *component)
+{
+	return (snd_soc_component_read32(component, SGTL5000_CHIP_ANA_CTRL) &
+		SGTL5000_HP_SEL_MASK) >> SGTL5000_HP_SEL_SHIFT;
+}
+
+static inline u16 mute_output(struct snd_soc_component *component,
+			      u16 mute_mask)
+{
+	u16 mute_reg = snd_soc_component_read32(component,
+					      SGTL5000_CHIP_ANA_CTRL);
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+			    mute_mask, mute_mask);
+	return mute_reg;
+}
+
+static inline void restore_output(struct snd_soc_component *component,
+				  u16 mute_mask, u16 mute_reg)
+{
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_CTRL,
+		mute_mask, mute_reg);
+}
+
+static void vag_power_on(struct snd_soc_component *component, u32 source)
+{
+	if (snd_soc_component_read32(component, SGTL5000_CHIP_ANA_POWER) &
+	    SGTL5000_VAG_POWERUP)
+		return;
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
+			    SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);
+
+	/* When VAG powering on to get local loop from Line-In, the sleep
+	 * is required to avoid loud pop.
+	 */
+	if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN &&
+	    source == HP_POWER_EVENT)
+		msleep(SGTL5000_VAG_POWERUP_DELAY);
+}
+
+static int vag_power_consumers(struct snd_soc_component *component,
+			       u16 ana_pwr_reg, u32 source)
+{
+	int consumers = 0;
+
+	/* count dac/adc consumers unconditional */
+	if (ana_pwr_reg & SGTL5000_DAC_POWERUP)
+		consumers++;
+	if (ana_pwr_reg & SGTL5000_ADC_POWERUP)
+		consumers++;
+
+	/*
+	 * If the event comes from HP and Line-In is selected,
+	 * current action is 'DAC to be powered down'.
+	 * As HP_POWERUP is not set when HP muxed to line-in,
+	 * we need to keep VAG power ON.
+	 */
+	if (source == HP_POWER_EVENT) {
+		if (hp_sel_input(component) == SGTL5000_HP_SEL_LINE_IN)
+			consumers++;
+	} else {
+		if (ana_pwr_reg & SGTL5000_HP_POWERUP)
+			consumers++;
+	}
+
+	return consumers;
+}
+
+static void vag_power_off(struct snd_soc_component *component, u32 source)
+{
+	u16 ana_pwr = snd_soc_component_read32(component,
+					     SGTL5000_CHIP_ANA_POWER);
+
+	if (!(ana_pwr & SGTL5000_VAG_POWERUP))
+		return;
+
+	/*
+	 * This function calls when any of VAG power consumers is disappearing.
+	 * Thus, if there is more than one consumer at the moment, as minimum
+	 * one consumer will definitely stay after the end of the current
+	 * event.
+	 * Don't clear VAG_POWERUP if 2 or more consumers of VAG present:
+	 * - LINE_IN (for HP events) / HP (for DAC/ADC events)
+	 * - DAC
+	 * - ADC
+	 * (the current consumer is disappearing right now)
+	 */
+	if (vag_power_consumers(component, ana_pwr, source) >= 2)
+		return;
+
+	snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
+		SGTL5000_VAG_POWERUP, 0);
+	/* In power down case, we need wait 400-1000 ms
+	 * when VAG fully ramped down.
+	 * As longer we wait, as smaller pop we've got.
+	 */
+	msleep(SGTL5000_VAG_POWERDOWN_DELAY);
+}
+
 /*
  * mic_bias power on/off share the same register bits with
  * output impedance of mic bias, when power on mic bias, we
@@ -170,40 +290,79 @@ static int mic_bias_event(struct snd_soc_dapm_widget *w,
 	return 0;
 }
 
-/*
- * As manual described, ADC/DAC only works when VAG powerup,
- * So enabled VAG before ADC/DAC up.
- * In power down case, we need wait 400ms when vag fully ramped down.
- */
-static int power_vag_event(struct snd_soc_dapm_widget *w,
-	struct snd_kcontrol *kcontrol, int event)
+static void vag_and_mute_control(struct snd_soc_component *component,
+				 int event, int event_source,
+				 u16 mute_mask, u16 *mute_reg)
 {
-	struct snd_soc_component *component = snd_soc_dapm_to_component(w->dapm);
-	const u32 mask = SGTL5000_DAC_POWERUP | SGTL5000_ADC_POWERUP;
-
 	switch (event) {
-	case SND_SOC_DAPM_POST_PMU:
-		snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
-			SGTL5000_VAG_POWERUP, SGTL5000_VAG_POWERUP);
-		msleep(400);
+	case SND_SOC_DAPM_PRE_PMU:
+		*mute_reg = mute_output(component, mute_mask);
+		break;
+	case SND_SOC_DAPM_POST_PMU:
+		vag_power_on(component, event_source);
+		restore_output(component, mute_mask, *mute_reg);
 		break;
-
 	case SND_SOC_DAPM_PRE_PMD:
-		/*
-		 * Don't clear VAG_POWERUP, when both DAC and ADC are
-		 * operational to prevent inadvertently starving the
-		 * other one of them.
-		 */
-		if ((snd_soc_component_read32(component, SGTL5000_CHIP_ANA_POWER) &
-				mask) != mask) {
-			snd_soc_component_update_bits(component, SGTL5000_CHIP_ANA_POWER,
-				SGTL5000_VAG_POWERUP, 0);
-			msleep(400);
-		}
+		*mute_reg = mute_output(component, mute_mask);
+		vag_power_off(component, event_source);
+		break;
+	case SND_SOC_DAPM_POST_PMD:
+		restore_output(component, mute_mask, *mute_reg);
 		break;
 	default:
 		break;
 	}
+}
+
+/*
+ * Mute Headphone when power it up/down.
+ * Control VAG power on HP power path.
+ */
+static int headphone_pga_event(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, HP_POWER_EVENT,
+			     SGTL5000_HP_MUTE,
+			     &sgtl5000->mute_state.hp_event);
+
+	return 0;
+}
+
+/* As manual describes, ADC/DAC powering up/down requires
+ * to mute outputs to avoid pops.
+ * Control VAG power on ADC/DAC power path.
+ */
+static int adc_updown_depop(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, ADC_POWER_EVENT,
+			     SGTL5000_OUTPUTS_MUTE,
+			     &sgtl5000->mute_state.adc_event);
+
+	return 0;
+}
+
+static int dac_updown_depop(struct snd_soc_dapm_widget *w,
+	struct snd_kcontrol *kcontrol, int event)
+{
+	struct snd_soc_component *component =
+		snd_soc_dapm_to_component(w->dapm);
+	struct sgtl5000_priv *sgtl5000 =
+		snd_soc_component_get_drvdata(component);
+
+	vag_and_mute_control(component, event, DAC_POWER_EVENT,
+			     SGTL5000_OUTPUTS_MUTE,
+			     &sgtl5000->mute_state.dac_event);
 
 	return 0;
 }
@@ -280,7 +439,10 @@ static const struct snd_soc_dapm_widget sgtl5000_dapm_widgets[] = {
 			    mic_bias_event,
 			    SND_SOC_DAPM_POST_PMU | SND_SOC_DAPM_PRE_PMD),
 
-	SND_SOC_DAPM_PGA("HP", SGTL5000_CHIP_ANA_POWER, 4, 0, NULL, 0),
+	SND_SOC_DAPM_PGA_E("HP", SGTL5000_CHIP_ANA_POWER, 4, 0, NULL, 0,
+			   headphone_pga_event,
+			   SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
 	SND_SOC_DAPM_PGA("LO", SGTL5000_CHIP_ANA_POWER, 0, 0, NULL, 0),
 
 	SND_SOC_DAPM_MUX("Capture Mux", SND_SOC_NOPM, 0, 0, &adc_mux),
@@ -301,11 +463,12 @@ static const struct snd_soc_dapm_widget sgtl5000_dapm_widgets[] = {
 				0, SGTL5000_CHIP_DIG_POWER,
 				1, 0),
 
-	SND_SOC_DAPM_ADC("ADC", "Capture", SGTL5000_CHIP_ANA_POWER, 1, 0),
-	SND_SOC_DAPM_DAC("DAC", "Playback", SGTL5000_CHIP_ANA_POWER, 3, 0),
-
-	SND_SOC_DAPM_PRE("VAG_POWER_PRE", power_vag_event),
-	SND_SOC_DAPM_POST("VAG_POWER_POST", power_vag_event),
+	SND_SOC_DAPM_ADC_E("ADC", "Capture", SGTL5000_CHIP_ANA_POWER, 1, 0,
+			   adc_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
+	SND_SOC_DAPM_DAC_E("DAC", "Playback", SGTL5000_CHIP_ANA_POWER, 3, 0,
+			   dac_updown_depop, SND_SOC_DAPM_PRE_POST_PMU |
+			   SND_SOC_DAPM_PRE_POST_PMD),
 };
 
 /* routes for sgtl5000 */
-- 
2.20.1


-- 

Ciklum refers to one or more of Ciklum Group Holdings LTD. and its 
subsidiaries and affiliates each of which is a legally separate entity. 
Ciklum LLC is a limited liability company registered in Ukraine under 
EDRPOU code 31902643, with its registered address at 12 Amosova St., 03680, 
Kyiv, Ukraine.



The contents of this e-mail (including any attachments) 
are confidential and may be legally privileged. If you are not the intended 
recipient of this e-mail, please notify the sender immediately and then 
delete it (including any attachments) from all your systems. Any 
unauthorised use, reproduction, distribution, disclosure and/or 
modification of this message and/or its contents are strictly prohibited. 
We cannot guarantee that this e-mail is secure or error-free. Ciklum cannot 
be held liable for any loss or damage caused by software viruses or 
resulting from any use of or reliance on this email by anyone, other than 
the intended addressee to the extent agreed in a contract for the matter to 
which this email relates (if any). Messages sent to and from Ciklum may be 
monitored; by replying to this e-mail you give your consent to such 
monitoring.  Notice: we do not accept service by e-mail of court 
proceedings, other processes or formal notices of any kind without specific 
prior written agreement. This email does not constitute a binding offer or 
acceptance for Ciklum unless so set forth in a separate document.