Re: [PATCH v4 5/5] Bluetooth: btusb: Use the hw_reset method to allow resetting the BT chip

[Marcel Holtmann]

Hi Rajat,

> If the platform provides it, use the reset gpio to reset the BT
> chip (requested by the HCI core if needed). This has been found helpful
> on some of Intel bluetooth controllers where the firmware gets stuck and
> the only way out is a hard reset pin provided by the platform.
> 
> Signed-off-by: Rajat Jain <rajatja@xxxxxxxxxx>
> ---
> v4: Use data->flags instead of clearing the quirk in btusb_hw_reset()
> v3: Better error handling for gpiod_get_optional()
> v2: Handle the EPROBE_DEFER case.
> 
> drivers/bluetooth/btusb.c | 45 +++++++++++++++++++++++++++++++++++++++
> 1 file changed, 45 insertions(+)
> 
> diff --git a/drivers/bluetooth/btusb.c b/drivers/bluetooth/btusb.c
> index 59869643cc29..7cf1e4f749e9 100644
> --- a/drivers/bluetooth/btusb.c
> +++ b/drivers/bluetooth/btusb.c
> @@ -29,6 +29,7 @@
> #include <linux/of_device.h>
> #include <linux/of_irq.h>
> #include <linux/suspend.h>
> +#include <linux/gpio/consumer.h>
> #include <asm/unaligned.h>
> 
> #include <net/bluetooth/bluetooth.h>
> @@ -439,6 +440,7 @@ static const struct dmi_system_id btusb_needs_reset_resume_table[] = {
> #define BTUSB_BOOTING		9
> #define BTUSB_DIAG_RUNNING	10
> #define BTUSB_OOB_WAKE_ENABLED	11
> +#define BTUSB_HW_RESET_DONE	12

I think you mean BTUSB_HW_RESET_ACTIVE or BTUSB_HW_RESET_IN_PROGRESS.

> 
> struct btusb_data {
> 	struct hci_dev       *hdev;
> @@ -476,6 +478,8 @@ struct btusb_data {
> 	struct usb_endpoint_descriptor *diag_tx_ep;
> 	struct usb_endpoint_descriptor *diag_rx_ep;
> 
> +	struct gpio_desc *reset_gpio;
> +
> 	__u8 cmdreq_type;
> 	__u8 cmdreq;
> 
> @@ -491,6 +495,30 @@ struct btusb_data {
> 	int oob_wake_irq;   /* irq for out-of-band wake-on-bt */
> };
> 
> +
> +static void btusb_hw_reset(struct hci_dev *hdev)
> +{
> +	struct btusb_data *data = hci_get_drvdata(hdev);
> +	struct gpio_desc *reset_gpio = data->reset_gpio;
> +
> +	/*
> +	 * Toggle the hard reset line if the platform provides one. The reset
> +	 * is going to yank the device off the USB and then replug. So doing
> +	 * once is enough. The cleanup is handled correctly on the way out
> +	 * (standard USB disconnect), and the new device is detected cleanly
> +	 * and bound to the driver again like it should be.
> +	 */
> +	if (test_and_set_bit(BTUSB_HW_RESET_DONE, &data->flags)) {
> +		bt_dev_warn(hdev, "last reset failed? Not resetting again\n");
> +		return;
> +	}
> +
> +	bt_dev_dbg(hdev, "Initiating HW reset via gpio\nâ);

The bt_dev_ functions donât need the \n at the end.

> +	gpiod_set_value(reset_gpio, 1);
> +	mdelay(100);
> +	gpiod_set_value(reset_gpio, 0);
> +}
> +
> static inline void btusb_free_frags(struct btusb_data *data)
> {
> 	unsigned long flags;
> @@ -2915,6 +2943,7 @@ static int btusb_probe(struct usb_interface *intf,
> 		       const struct usb_device_id *id)
> {
> 	struct usb_endpoint_descriptor *ep_desc;
> +	struct gpio_desc *reset_gpio;
> 	struct btusb_data *data;
> 	struct hci_dev *hdev;
> 	unsigned ifnum_base;
> @@ -3028,6 +3057,16 @@ static int btusb_probe(struct usb_interface *intf,
> 
> 	SET_HCIDEV_DEV(hdev, &intf->dev);
> 
> +	reset_gpio = gpiod_get_optional(&data->udev->dev, "reset",
> +					GPIOD_OUT_LOW);
> +	if (IS_ERR(reset_gpio)) {
> +		err = PTR_ERR(reset_gpio);
> +		goto out_free_dev;
> +	} else if (reset_gpio) {
> +		data->reset_gpio = reset_gpio;
> +		hdev->hw_reset = btusb_hw_reset;
> +	}
> +
> 	hdev->open   = btusb_open;
> 	hdev->close  = btusb_close;
> 	hdev->flush  = btusb_flush;
> @@ -3083,6 +3122,7 @@ static int btusb_probe(struct usb_interface *intf,
> 		set_bit(HCI_QUIRK_STRICT_DUPLICATE_FILTER, &hdev->quirks);
> 		set_bit(HCI_QUIRK_SIMULTANEOUS_DISCOVERY, &hdev->quirks);
> 		set_bit(HCI_QUIRK_NON_PERSISTENT_DIAG, &hdev->quirks);
> +		set_bit(HCI_QUIRK_HW_RESET_ON_TIMEOUT, &hdev->quirks);
> 
> 		if (id->driver_info & BTUSB_INTEL) {
> 			hdev->setup = btusb_setup_intel;
> @@ -3223,6 +3263,8 @@ static int btusb_probe(struct usb_interface *intf,
> 	return 0;
> 
> out_free_dev:
> +	if (data->reset_gpio)
> +		gpiod_put(data->reset_gpio);
> 	hci_free_dev(hdev);
> 	return err;
> }
> @@ -3266,6 +3308,9 @@ static void btusb_disconnect(struct usb_interface *intf)
> 	if (data->oob_wake_irq)
> 		device_init_wakeup(&data->udev->dev, false);
> 
> +	if (data->reset_gpio)
> +		gpiod_put(data->reset_gpio);
> +
> 	hci_free_dev(hdev);
> }

Regards

Marcel