Re: [PATCH v7 1/4] dt-bindings: pps: descriptor-based gpio, capture-clear addition

From: tom burkart
Date: Wed Nov 28 2018 - 19:29:51 EST


Quoting Rob Herring <robh@xxxxxxxxxx>:

On Mon, Nov 26, 2018 at 9:57 PM tom burkart <tom@xxxxxxxxxx> wrote:

Quoting Rob Herring <robh@xxxxxxxxxx>:

> On Sat, Nov 17, 2018 at 6:35 PM tom burkart <tom@xxxxxxxxxx> wrote:
>>
>> Quoting Rob Herring <robh@xxxxxxxxxx>:
>>
>> > On Sat, Nov 17, 2018 at 4:35 AM tom burkart <tom@xxxxxxxxxx> wrote:
>> >>
>> >> Quoting Rob Herring <robh@xxxxxxxxxx>:
>> >>
>> >> > On Wed, Nov 14, 2018 at 11:54:29PM +1100, Tom Burkart wrote:
>> >> >> This patch changes the devicetree bindings for the pps-gpio driver
>> >> >> from the integer based ABI to the descriptor based ABI.
>> >> > ? That has nothing to do with DT.
>> >>
>> >> I believe it does, as the change in ABI forces a rename in the DT
>> >> naming convention.
>> >> This is due to the descriptor based ABI appending "-gpio" or
>> "-gpios" (see
>> >> Documentation/gpio/base.txt.)
>> >> Admittedly, I may have called it by the wrong name due to ignorance,
>> >> my apologies.
>> >
>> > If what you say is correct, then you can't change this driver. You'll
>> > break compatibility with any existing DT.
>> >
>> > Changing the binding reasoning should purely be that this is the
>> > preferred form. Bindings must be independent from changing kernel
>> > APIs.
>>
>> See comments from Philip Zabel. I misread the documentation and this
>> has now been corrected in v8 of the patch. I hope that eliminates all
>> comments made above.
>>
>> >> >> It also adds
>> >> >> documentation for the device tree capture-clear option. The legacy
>> >> >> device tree entry for the GPIO pin is supported.
>> >> >>
>> >> >> Signed-off-by: Tom Burkart <tom@xxxxxxxxxx>
>> >> >> ---
>> >> >> Documentation/devicetree/bindings/pps/pps-gpio.txt | 8 ++++++--
>> >> >> 1 file changed, 6 insertions(+), 2 deletions(-)
>> >> >>
>> >> >> diff --git a/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> >> b/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> >> index 3683874832ae..6c9fc0998d94 100644
>> >> >> --- a/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> >> +++ b/Documentation/devicetree/bindings/pps/pps-gpio.txt
>> >> >> @@ -5,19 +5,23 @@ a GPIO pin.
>> >> >>
>> >> >> Required properties:
>> >> >> - compatible: should be "pps-gpio"
>> >> >> -- gpios: one PPS GPIO in the format described by ../gpio/gpio.txt
>> >> >> +- pps-gpios: one PPS GPIO in the format described by ../gpio/gpio.txt
>> >> >> +Alternatively (DEPRECATED), instead of pps-gpios above, it may have:
>> >> >> +- gpios: one PPS GPIO as above
>> >> >>
>> >> >> Optional properties:
>> >> >> - assert-falling-edge: when present, assert is indicated by a
>> >> falling edge
>> >> >> (instead of by a rising edge)
>> >> >> +- capture-clear: when present, also capture the PPS clear event
>> >> >
>> >> > Is this a h/w thing? or driver configuration?
>> >>
>> >> Driver configuration. Most of the code was present in the driver, yet
>> >> it was not documented, or usable due to a two line (code) omission
>> >> (the value was not being fetched from DT).
>> >
>> > So what determines how you want to configure this? If the user will
>> > want to change it, then it should be a sysfs attr and exposed to
>> > userspace. If it depends on h/w config for a board then it can be in
>> > DT.
>>
>> Sorry, I misled you somewhat. If the PPS pulse active transition from
>> the hardware is on the falling edge, this flag is required to get the
>> OS to use that as the active transition. This would not change at the
>> user's whim but rather it is dependent on connected hardware.
>
> This description sounds more like 'assert-falling-edge' than 'capture-clear'.
>
> I'm still not clear on what 'capture-clear' is.

Ignoring my patch for a minute, the pps_gpio_irq_handler will only
report a pps PPS_CAPTURECLEAR event if 'capture-clear' is set. As the
current pps-gpio driver is not able to set this flag, it cannot ever
report a PPS_CAPTURECLEAR event.

My patch adds the ability to set this flag and adds the documentation
to go with it.
Admittedly, I do not require this functionality for what I want, but
working with the code, I noticed the omission and decided to add it
for someone else to use it, if they need it.

I am happy to remove this out of my patch, if you feel this to be the
best way forward.

I found this prior discussion on adding this[1]. Seems to me this
should be userspace configurable if the GPIO line can interrupt on
both edges. We shouldn't need a DT property to determine that.

Rob

[1] https://lore.kernel.org/patchwork/patch/557781/

Patch v11 has just been sent that has no changes to the capture-clear DT option.

Tom