Re: [PATCH v2 2/2] [media] imx214: Add imx214 camera sensor driver

From: Ricardo Ribalda Delgado
Date: Mon Sep 24 2018 - 07:20:40 EST


Hi Jacopo

Thanks a lot for your review. Will push the changes to
https://github.com/ribalda/linux/tree/imx214-v3 and then to this list
at the end of this week./beggining of the next
On Mon, Sep 24, 2018 at 10:35 AM jacopo mondi <jacopo@xxxxxxxxxx> wrote:
>
> Hi Ricardo,
> thanks for the patch.
>
> A few comments, please see below.
>
>
> On Fri, Sep 21, 2018 at 12:09:20PM +0200, Ricardo Ribalda Delgado wrote:
> > Add a V4L2 sub-device driver for the Sony IMX214 image sensor.
> > This is a camera sensor using the I2C bus for control and the
> > CSI-2 bus for data.
> >
> > Tested on a DB820c alike board with Intrinsyc Open-Q 13MP camera.
> >
> > Signed-off-by: Ricardo Ribalda Delgado <ricardo.ribalda@xxxxxxxxx>
> > ---
> > Since v2: Thanks Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> > - Use regulator_bulk
> > - Do not set voltages, let the DT do that
> > - missing consts
> > - remove i2c_client
> >
> > MAINTAINERS | 8 +
> > drivers/media/i2c/Kconfig | 12 +
> > drivers/media/i2c/Makefile | 1 +
> > drivers/media/i2c/imx214.c | 956 +++++++++++++++++++++++++++++++++++++
> > 4 files changed, 977 insertions(+)
> > create mode 100644 drivers/media/i2c/imx214.c
> >
> > diff --git a/MAINTAINERS b/MAINTAINERS
> > index 9989925f658d..2ae68894e700 100644
> > --- a/MAINTAINERS
> > +++ b/MAINTAINERS
> > @@ -13521,6 +13521,14 @@ S: Maintained
> > F: drivers/ssb/
> > F: include/linux/ssb/
> >
> > +SONY IMX214 SENSOR DRIVER
> > +M: Ricardo Ribalda <ricardo.ribalda@xxxxxxxxx>
> > +L: linux-media@xxxxxxxxxxxxxxx
> > +T: git git://linuxtv.org/media_tree.git
> > +S: Maintained
> > +F: drivers/media/i2c/imx214.c
> > +F: Documentation/devicetree/bindings/media/i2c/imx214.txt
> > +
> > SONY IMX258 SENSOR DRIVER
> > M: Sakari Ailus <sakari.ailus@xxxxxxxxxxxxxxx>
> > L: linux-media@xxxxxxxxxxxxxxx
> > diff --git a/drivers/media/i2c/Kconfig b/drivers/media/i2c/Kconfig
> > index bfdb494686bf..d9416b3a090c 100644
> > --- a/drivers/media/i2c/Kconfig
> > +++ b/drivers/media/i2c/Kconfig
> > @@ -595,6 +595,18 @@ config VIDEO_APTINA_PLL
> > config VIDEO_SMIAPP_PLL
> > tristate
> >
> > +config VIDEO_IMX214
> > + tristate "Sony IMX214 sensor support"
> > + depends on GPIOLIB && I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
> > + depends on OF
> > + depends on MEDIA_CAMERA_SUPPORT
> > + help
> > + This is a Video4Linux2 sensor driver for the Sony
> > + IMX214 camera.
> > +
> > + To compile this driver as a module, choose M here: the
> > + module will be called imx214.
> > +
> > config VIDEO_IMX258
> > tristate "Sony IMX258 sensor support"
> > depends on I2C && VIDEO_V4L2 && VIDEO_V4L2_SUBDEV_API
> > diff --git a/drivers/media/i2c/Makefile b/drivers/media/i2c/Makefile
> > index a94eb03d10d4..61305edc6165 100644
> > --- a/drivers/media/i2c/Makefile
> > +++ b/drivers/media/i2c/Makefile
> > @@ -106,6 +106,7 @@ obj-$(CONFIG_VIDEO_I2C) += video-i2c.o
> > obj-$(CONFIG_VIDEO_ML86V7667) += ml86v7667.o
> > obj-$(CONFIG_VIDEO_OV2659) += ov2659.o
> > obj-$(CONFIG_VIDEO_TC358743) += tc358743.o
> > +obj-$(CONFIG_VIDEO_IMX214) += imx214.o
> > obj-$(CONFIG_VIDEO_IMX258) += imx258.o
> > obj-$(CONFIG_VIDEO_IMX274) += imx274.o
> >
> > diff --git a/drivers/media/i2c/imx214.c b/drivers/media/i2c/imx214.c
> > new file mode 100644
> > index 000000000000..ea5beba13b04
> > --- /dev/null
> > +++ b/drivers/media/i2c/imx214.c
> > @@ -0,0 +1,956 @@
> > +// SPDX-License-Identifier: GPL-2.0
> > +/*
> > + * imx214.c - imx214 sensor driver
> > + *
> > + * Copyright 2018 Qtechnology A/S
> > + *
> > + * Ricardo Ribalda <ricardo.ribalda@xxxxxxxxx>
> > + */
> > +#include <linux/i2c.h>
> > +#include <linux/module.h>
> > +#include <linux/clk.h>
> > +#include <linux/regulator/consumer.h>
> > +#include <linux/gpio/consumer.h>
> > +#include <linux/delay.h>
> > +#include <linux/regmap.h>
> > +#include <media/media-entity.h>
> > +#include <media/v4l2-fwnode.h>
> > +#include <media/v4l2-subdev.h>
> > +#include <media/v4l2-ctrls.h>
>
> Nit: could you sort header files please?
>
> > +
> > +#define IMX214_DEFAULT_CLK_FREQ 24000000
> > +#define IMX214_DEFAULT_PIXEL_RATE 384000000
> > +#define IMX214_WIDTH 4096
> > +#define IMX214_HEIGHT 2304
>
> I don't see the two above defines ever used.
>
> > +#define IMX214_FPS 30
> > +#define IMX214_MBUS_CODE MEDIA_BUS_FMT_SRGGB10_1X10
> > +
> > +static const char * const imx214_supply_name[] = {
> > + "vdda",
> > + "vddd",
> > + "vdddo",
> > +};
> > +
> > +#define IMX214_NUM_SUPPLIES ARRAY_SIZE(imx214_supply_name)
> > +
> > +struct imx214 {
> > + struct device *dev;
> > + struct clk *xclk;
> > + struct regmap *regmap;
> > +
> > + struct v4l2_fwnode_endpoint ep;
> > + struct v4l2_subdev sd;
> > + struct media_pad pad;
> > + struct v4l2_mbus_framefmt fmt;
> > + struct v4l2_rect crop;
> > +
> > + struct v4l2_ctrl_handler ctrls;
> > + struct v4l2_ctrl *pixel_rate;
> > + struct v4l2_ctrl *link_freq;
> > +
> > + struct regulator_bulk_data supplies[IMX214_NUM_SUPPLIES];
> > +
> > + struct gpio_desc *enable_gpio;
> > +
> > + bool power_on;
> > +};
> > +
> > +struct reg_8 {
> > + u16 addr;
> > + u8 val;
> > +};
> > +
> > +static const struct reg_8 mode_1920x1080[];
> > +static const struct reg_8 mode_4096x2304[];
>
> Can you move those regsiter tables here and avoid forward declaring
> them, or is there a reason I am missing for not doing that?

I want the imx214_modes to be on top. They show the capabilities of
the driver in a fast view.
So it is more a personal taste. But if it breaks any rule I will
reoder this, no problem ;)

>
> > +
> > +/*
> > + * Declare modes in order, from biggest
> > + * to smallest height.
> > + */
> > +static const struct imx214_mode {
> > + u32 width;
> > + u32 height;
> > + const struct reg_8 *reg_table;
> > +} imx214_modes[] = {
> > + {
> > + .width = 4096,
> > + .height = 2304,
> > + .reg_table = mode_4096x2304,
> > + },
> > + {
> > + .width = 1920,
> > + .height = 1080,
> > + .reg_table = mode_1920x1080,
> > + },
> > +};
> > +
> > +static inline struct imx214 *to_imx214(struct v4l2_subdev *sd)
> > +{
> > + return container_of(sd, struct imx214, sd);
> > +}
> > +
> > +static int imx214_set_power_on(struct imx214 *imx214)
> > +{
> > + int ret;
> > +
> > + gpiod_set_value_cansleep(imx214->enable_gpio, 0);
> > + usleep_range(10, 20);
> > +
> > + ret = regulator_bulk_enable(IMX214_NUM_SUPPLIES, imx214->supplies);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "failed to enable regulators: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + usleep_range(2000, 3000);
> > +
> > + ret = clk_prepare_enable(imx214->xclk);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "clk prepare enable failed\n");
> > + return ret;
> > + }
> > +
> > +
> > + gpiod_set_value_cansleep(imx214->enable_gpio, 1);
> > + usleep_range(12000, 15000);
> > +
> > + return 0;
> > +}
> > +
> > +static void imx214_set_power_off(struct imx214 *imx214)
> > +{
> > + gpiod_set_value_cansleep(imx214->enable_gpio, 0);
> > +
> > + clk_disable_unprepare(imx214->xclk);
> > +
> > + regulator_bulk_disable(IMX214_NUM_SUPPLIES, imx214->supplies);
> > +}
> > +
> > +static int imx214_s_power(struct v4l2_subdev *sd, int on)
> > +{
> > + struct imx214 *imx214 = to_imx214(sd);
> > + int ret = 0;
> > +
> > + on = !!on;
> > +
> > + if (imx214->power_on == on)
> > + return 0;
> > +
> > + if (on)
> > + ret = imx214_set_power_on(imx214);
> > + else
> > + imx214_set_power_off(imx214);
> > +
> > + imx214->power_on = on;
>
> Nit: blank line before return, here and in other places in the driver.
>
> > + return 0;
> > +}
> > +
> > +static int imx214_enum_mbus_code(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_mbus_code_enum *code)
> > +{
> > + if (code->index > 0)
> > + return -EINVAL;
> > +
> > + code->code = IMX214_MBUS_CODE;
> > +
> > + return 0;
> > +}
> > +
> > +static int imx214_enum_frame_size(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_frame_size_enum *fse)
> > +{
> > + if (fse->code != IMX214_MBUS_CODE)
> > + return -EINVAL;
> > +
> > + if (fse->index >= ARRAY_SIZE(imx214_modes))
> > + return -EINVAL;
> > +
> > + fse->min_width = fse->max_width = imx214_modes[fse->index].width;
> > + fse->min_height = fse->max_height = imx214_modes[fse->index].height;
> > +
> > + return 0;
> > +}
> > +
> > +#ifdef CONFIG_VIDEO_ADV_DEBUG
> > +static int imx214_s_register(struct v4l2_subdev *subdev,
> > + const struct v4l2_dbg_register *reg)
> > +{
> > + struct imx214 *imx214 = container_of(subdev, struct imx214, sd);
> > +
> > + return regmap_write(imx214->regmap, reg->reg, reg->val);
> > +}
> > +
> > +static int imx214_g_register(struct v4l2_subdev *subdev,
> > + struct v4l2_dbg_register *reg)
> > +{
> > + struct imx214 *imx214 = container_of(subdev, struct imx214, sd);
> > + unsigned int aux;
> > + int ret;
> > +
> > + reg->size = 1;
> > + ret = regmap_read(imx214->regmap, reg->reg, &aux);
> > + reg->val = aux;
> > + return ret;
> > +}
> > +#endif
> > +
> > +static const struct v4l2_subdev_core_ops imx214_core_ops = {
> > +#ifdef CONFIG_VIDEO_ADV_DEBUG
> > + .g_register = imx214_g_register,
> > + .s_register = imx214_s_register,
> > +#endif
> > + .s_power = imx214_s_power,
> > +};
> > +
> > +static struct v4l2_mbus_framefmt *
> > +__imx214_get_pad_format(struct imx214 *imx214,
> > + struct v4l2_subdev_pad_config *cfg,
> > + unsigned int pad,
> > + enum v4l2_subdev_format_whence which)
> > +{
> > + switch (which) {
> > + case V4L2_SUBDEV_FORMAT_TRY:
> > + return v4l2_subdev_get_try_format(&imx214->sd, cfg, pad);
> > + case V4L2_SUBDEV_FORMAT_ACTIVE:
> > + return &imx214->fmt;
> > + default:
> > + return NULL;
> > + }
> > +}
> > +
> > +static int imx214_get_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct imx214 *imx214 = to_imx214(sd);
> > +
> > + format->format = *__imx214_get_pad_format(imx214, cfg, format->pad,
> > + format->which);
> > +
> > + return 0;
> > +}
> > +
> > +static struct v4l2_rect *
> > +__imx214_get_pad_crop(struct imx214 *imx214, struct v4l2_subdev_pad_config *cfg,
> > + unsigned int pad, enum v4l2_subdev_format_whence which)
> > +{
> > + switch (which) {
> > + case V4L2_SUBDEV_FORMAT_TRY:
> > + return v4l2_subdev_get_try_crop(&imx214->sd, cfg, pad);
> > + case V4L2_SUBDEV_FORMAT_ACTIVE:
> > + return &imx214->crop;
> > + default:
> > + return NULL;
> > + }
> > +}
> > +
> > +static int imx214_find_mode(u32 height)
> > +{
> > + int i;
> > +
> > + for (i = 0; (i < ARRAY_SIZE(imx214_modes) - 1) ; i++)
> > + if (height >= imx214_modes[i].width)
>
> Comparing height and width?

Ups.... at the begiing I was using widht, then I moved to height....
Great catch!

>
> > + return i;
> > + return i;
> > +}
> > +
> > +static int imx214_set_format(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_format *format)
> > +{
> > + struct imx214 *imx214 = to_imx214(sd);
> > + struct v4l2_mbus_framefmt *__format;
> > + struct v4l2_rect *__crop;
> > + int mode;
> > +
> > + __crop = __imx214_get_pad_crop(imx214, cfg, format->pad, format->which);
> > +
> > + mode = format ? imx214_find_mode(format->format.height) : 0;
> > +
> > + __crop->width = imx214_modes[mode].width;
> > + __crop->height = imx214_modes[mode].height;
> > +
> > + __format = __imx214_get_pad_format(imx214, cfg, format->pad,
> > + format->which);
> > + __format->width = __crop->width;
> > + __format->height = __crop->height;
> > + __format->code = IMX214_MBUS_CODE;
> > + __format->field = V4L2_FIELD_NONE;
> > + __format->colorspace = V4L2_COLORSPACE_SRGB;
> > + __format->ycbcr_enc = V4L2_MAP_YCBCR_ENC_DEFAULT(__format->colorspace);
> > + __format->quantization = V4L2_MAP_QUANTIZATION_DEFAULT(true,
> > + __format->colorspace, __format->ycbcr_enc);
> > + __format->xfer_func = V4L2_MAP_XFER_FUNC_DEFAULT(__format->colorspace);
> > +
> > + format->format = *__format;
> > +
> > + return 0;
> > +}
> > +
> > +static int imx214_get_selection(struct v4l2_subdev *sd,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_selection *sel)
> > +{
> > + struct imx214 *imx214 = to_imx214(sd);
> > +
> > + if (sel->target != V4L2_SEL_TGT_CROP)
> > + return -EINVAL;
> > +
> > + sel->r = *__imx214_get_pad_crop(imx214, cfg, sel->pad,
> > + sel->which);
> > + return 0;
> > +}
> > +
> > +static int imx214_entity_init_cfg(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *cfg)
> > +{
> > + struct v4l2_subdev_format fmt = { };
> > +
> > + fmt.which = cfg ? V4L2_SUBDEV_FORMAT_TRY : V4L2_SUBDEV_FORMAT_ACTIVE;
> > + fmt.format.width = imx214_modes[0].width;
> > + fmt.format.height = imx214_modes[0].height;
> > +
> > + imx214_set_format(subdev, cfg, &fmt);
> > +
> > + return 0;
> > +}
> > +
> > +enum { IMX214_TABLE_WAIT_MS = 0,
> > + IMX214_TABLE_END,
> > + IMX214_MAX_RETRIES,
> > + IMX214_WAIT_MS};
> > +
> > +/*From imx214_mode_tbls.h*/
> > +static const struct reg_8 mode_4096x2304[] = {
> > + {0x0114, 0x03},
> > + {0x0220, 0x00},
> > + {0x0221, 0x11},
> > + {0x0222, 0x01},
> > + {0x0340, 0x0C},
> > + {0x0341, 0x7A},
> > + {0x0342, 0x13},
> > + {0x0343, 0x90},
> > + {0x0344, 0x00},
> > + {0x0345, 0x38},
> > + {0x0346, 0x01},
> > + {0x0347, 0x98},
> > + {0x0348, 0x10},
> > + {0x0349, 0x37},
> > + {0x034A, 0x0A},
> > + {0x034B, 0x97},
> > + {0x0381, 0x01},
> > + {0x0383, 0x01},
> > + {0x0385, 0x01},
> > + {0x0387, 0x01},
> > + {0x0900, 0x00},
> > + {0x0901, 0x00},
> > + {0x0902, 0x00},
> > + {0x3000, 0x35},
> > + {0x3054, 0x01},
> > + {0x305C, 0x11},
> > +
> > + {0x0112, 0x0A},
> > + {0x0113, 0x0A},
> > + {0x034C, 0x10},
> > + {0x034D, 0x00},
> > + {0x034E, 0x09},
> > + {0x034F, 0x00},
> > + {0x0401, 0x00},
> > + {0x0404, 0x00},
> > + {0x0405, 0x10},
> > + {0x0408, 0x00},
> > + {0x0409, 0x00},
> > + {0x040A, 0x00},
> > + {0x040B, 0x00},
> > + {0x040C, 0x10},
> > + {0x040D, 0x00},
> > + {0x040E, 0x09},
> > + {0x040F, 0x00},
> > +
> > + {0x0301, 0x05},
> > + {0x0303, 0x02},
> > + {0x0305, 0x03},
> > + {0x0306, 0x00},
> > + {0x0307, 0x96},
> > + {0x0309, 0x0A},
> > + {0x030B, 0x01},
> > + {0x0310, 0x00},
> > +
> > + {0x0820, 0x12},
> > + {0x0821, 0xC0},
> > + {0x0822, 0x00},
> > + {0x0823, 0x00},
> > +
> > + {0x3A03, 0x09},
> > + {0x3A04, 0x50},
> > + {0x3A05, 0x01},
> > +
> > + {0x0B06, 0x01},
> > + {0x30A2, 0x00},
> > +
> > + {0x30B4, 0x00},
> > +
> > + {0x3A02, 0xFF},
> > +
> > + {0x3011, 0x00},
> > + {0x3013, 0x01},
> > +
> > + {0x0202, 0x0C},
> > + {0x0203, 0x70},
> > + {0x0224, 0x01},
> > + {0x0225, 0xF4},
> > +
> > + {0x0204, 0x00},
> > + {0x0205, 0x00},
> > + {0x020E, 0x01},
> > + {0x020F, 0x00},
> > + {0x0210, 0x01},
> > + {0x0211, 0x00},
> > + {0x0212, 0x01},
> > + {0x0213, 0x00},
> > + {0x0214, 0x01},
> > + {0x0215, 0x00},
> > + {0x0216, 0x00},
> > + {0x0217, 0x00},
> > +
> > + {0x4170, 0x00},
> > + {0x4171, 0x10},
> > + {0x4176, 0x00},
> > + {0x4177, 0x3C},
> > + {0xAE20, 0x04},
> > + {0xAE21, 0x5C},
> > +
> > + {IMX214_TABLE_WAIT_MS, 10},
> > + {0x0138, 0x01},
> > + {IMX214_TABLE_END, 0x00}
> > +};
> > +
> > +static const struct reg_8 mode_1920x1080[] = {
> > + {0x0114, 0x03},
> > + {0x0220, 0x00},
> > + {0x0221, 0x11},
> > + {0x0222, 0x01},
> > + {0x0340, 0x0C},
> > + {0x0341, 0x7A},
> > + {0x0342, 0x13},
> > + {0x0343, 0x90},
> > + {0x0344, 0x04},
> > + {0x0345, 0x78},
> > + {0x0346, 0x03},
> > + {0x0347, 0xFC},
> > + {0x0348, 0x0B},
> > + {0x0349, 0xF7},
> > + {0x034A, 0x08},
> > + {0x034B, 0x33},
> > + {0x0381, 0x01},
> > + {0x0383, 0x01},
> > + {0x0385, 0x01},
> > + {0x0387, 0x01},
> > + {0x0900, 0x00},
> > + {0x0901, 0x00},
> > + {0x0902, 0x00},
> > + {0x3000, 0x35},
> > + {0x3054, 0x01},
> > + {0x305C, 0x11},
> > +
> > + {0x0112, 0x0A},
> > + {0x0113, 0x0A},
> > + {0x034C, 0x07},
> > + {0x034D, 0x80},
> > + {0x034E, 0x04},
> > + {0x034F, 0x38},
> > + {0x0401, 0x00},
> > + {0x0404, 0x00},
> > + {0x0405, 0x10},
> > + {0x0408, 0x00},
> > + {0x0409, 0x00},
> > + {0x040A, 0x00},
> > + {0x040B, 0x00},
> > + {0x040C, 0x07},
> > + {0x040D, 0x80},
> > + {0x040E, 0x04},
> > + {0x040F, 0x38},
> > +
> > + {0x0301, 0x05},
> > + {0x0303, 0x02},
> > + {0x0305, 0x03},
> > + {0x0306, 0x00},
> > + {0x0307, 0x96},
> > + {0x0309, 0x0A},
> > + {0x030B, 0x01},
> > + {0x0310, 0x00},
> > +
> > + {0x0820, 0x12},
> > + {0x0821, 0xC0},
> > + {0x0822, 0x00},
> > + {0x0823, 0x00},
> > +
> > + {0x3A03, 0x04},
> > + {0x3A04, 0xF8},
> > + {0x3A05, 0x02},
> > +
> > + {0x0B06, 0x01},
> > + {0x30A2, 0x00},
> > +
> > + {0x30B4, 0x00},
> > +
> > + {0x3A02, 0xFF},
> > +
> > + {0x3011, 0x00},
> > + {0x3013, 0x01},
> > +
> > + {0x0202, 0x0C},
> > + {0x0203, 0x70},
> > + {0x0224, 0x01},
> > + {0x0225, 0xF4},
> > +
> > + {0x0204, 0x00},
> > + {0x0205, 0x00},
> > + {0x020E, 0x01},
> > + {0x020F, 0x00},
> > + {0x0210, 0x01},
> > + {0x0211, 0x00},
> > + {0x0212, 0x01},
> > + {0x0213, 0x00},
> > + {0x0214, 0x01},
> > + {0x0215, 0x00},
> > + {0x0216, 0x00},
> > + {0x0217, 0x00},
> > +
> > + {0x4170, 0x00},
> > + {0x4171, 0x10},
> > + {0x4176, 0x00},
> > + {0x4177, 0x3C},
> > + {0xAE20, 0x04},
> > + {0xAE21, 0x5C},
> > +
> > + {IMX214_TABLE_WAIT_MS, 10},
> > + {0x0138, 0x01},
> > + {IMX214_TABLE_END, 0x00}
> > +};
> > +
> > +static struct reg_8 mode_table_common[] = {
> > + /* software reset */
> > +
> > + /* software standby settings */
> > + {0x0100, 0x00},
> > +
> > + /* ATR setting */
> > + {0x9300, 0x02},
> > +
> > + /* external clock setting */
> > + {0x0136, 0x18},
> > + {0x0137, 0x00},
> > +
> > + /* global setting */
> > + /* basic config */
> > + {0x0101, 0x00},
> > + {0x0105, 0x01},
> > + {0x0106, 0x01},
> > + {0x4550, 0x02},
> > + {0x4601, 0x00},
> > + {0x4642, 0x05},
> > + {0x6227, 0x11},
> > + {0x6276, 0x00},
> > + {0x900E, 0x06},
> > + {0xA802, 0x90},
> > + {0xA803, 0x11},
> > + {0xA804, 0x62},
> > + {0xA805, 0x77},
> > + {0xA806, 0xAE},
> > + {0xA807, 0x34},
> > + {0xA808, 0xAE},
> > + {0xA809, 0x35},
> > + {0xA80A, 0x62},
> > + {0xA80B, 0x83},
> > + {0xAE33, 0x00},
> > +
> > + /* analog setting */
> > + {0x4174, 0x00},
> > + {0x4175, 0x11},
> > + {0x4612, 0x29},
> > + {0x461B, 0x12},
> > + {0x461F, 0x06},
> > + {0x4635, 0x07},
> > + {0x4637, 0x30},
> > + {0x463F, 0x18},
> > + {0x4641, 0x0D},
> > + {0x465B, 0x12},
> > + {0x465F, 0x11},
> > + {0x4663, 0x11},
> > + {0x4667, 0x0F},
> > + {0x466F, 0x0F},
> > + {0x470E, 0x09},
> > + {0x4909, 0xAB},
> > + {0x490B, 0x95},
> > + {0x4915, 0x5D},
> > + {0x4A5F, 0xFF},
> > + {0x4A61, 0xFF},
> > + {0x4A73, 0x62},
> > + {0x4A85, 0x00},
> > + {0x4A87, 0xFF},
> > +
> > + /* embedded data */
> > + {0x5041, 0x04},
> > + {0x583C, 0x04},
> > + {0x620E, 0x04},
> > + {0x6EB2, 0x01},
> > + {0x6EB3, 0x00},
> > + {0x9300, 0x02},
> > +
> > + /* imagequality */
> > + /* HDR setting */
> > + {0x3001, 0x07},
> > + {0x6D12, 0x3F},
> > + {0x6D13, 0xFF},
> > + {0x9344, 0x03},
> > + {0x9706, 0x10},
> > + {0x9707, 0x03},
> > + {0x9708, 0x03},
> > + {0x9E04, 0x01},
> > + {0x9E05, 0x00},
> > + {0x9E0C, 0x01},
> > + {0x9E0D, 0x02},
> > + {0x9E24, 0x00},
> > + {0x9E25, 0x8C},
> > + {0x9E26, 0x00},
> > + {0x9E27, 0x94},
> > + {0x9E28, 0x00},
> > + {0x9E29, 0x96},
> > +
> > + /* CNR parameter setting */
> > + {0x69DB, 0x01},
> > +
> > + /* Moire reduction */
> > + {0x6957, 0x01},
> > +
> > + /* image enhancment */
> > + {0x6987, 0x17},
> > + {0x698A, 0x03},
> > + {0x698B, 0x03},
> > +
> > + /* white balanace */
> > + {0x0B8E, 0x01},
> > + {0x0B8F, 0x00},
> > + {0x0B90, 0x01},
> > + {0x0B91, 0x00},
> > + {0x0B92, 0x01},
> > + {0x0B93, 0x00},
> > + {0x0B94, 0x01},
> > + {0x0B95, 0x00},
> > +
> > + /* ATR setting */
> > + {0x6E50, 0x00},
> > + {0x6E51, 0x32},
> > + {0x9340, 0x00},
> > + {0x9341, 0x3C},
> > + {0x9342, 0x03},
> > + {0x9343, 0xFF},
> > + {IMX214_TABLE_END, 0x00}
> > +};
> > +
> > +#define MAX_CMD 4
> > +static int imx214_write_table(struct imx214 *imx214,
> > + const struct reg_8 table[])
> > +{
> > + u8 vals[MAX_CMD];
> > + int ret;
> > + int i;
> > +
> > + for (table = table; table->addr != IMX214_TABLE_END ; table++) {
> > + if (table->addr == IMX214_TABLE_WAIT_MS) {
> > + msleep(table->val);
>
> usleep_range might be better for 10msec sleeps?
>
> > + continue;
> > + }
> > +
> > + for (i = 0; i < MAX_CMD; i++) {
> > + if (table[i].addr != (table[0].addr + i))
> > + break;
> > + vals[i] = table[i].val;
> > + }
> > +
> > + ret = regmap_bulk_write(imx214->regmap, table->addr, vals, i);
>
> I'm not saying using regmap is wrong, but makes this function a bit
> cumbersome. You have delays as part of the command tables, that's
> fine, and you want to wait everytime you meet one, then proceed to
> write the rest. If you have your own write functions, this would look
> simpler, and if regmap helps in anyway in caching writes, you're anyway
> sending up to 4 entries at a time, which I think makes the regmap caching
> useless, imho.

I want to follow the pattern in other drivers here.

>
> > +
> > + if (ret) {
> > + dev_err(imx214->dev, "write_teable error: %d\n", ret);
> > + return ret;
> > + }
> > +
> > + table += i - 1;
> > +
> empty new line
>
> > + }
> > +
> > + return 0;
> > +}
> > +
>
> two empty new lines.
>
> > +
> > +static int imx214_s_stream(struct v4l2_subdev *subdev, int enable)
> > +{
> > + struct imx214 *imx214 = to_imx214(subdev);
> > + int ret;
> > +
> > + if (enable) {
> > + int mode = imx214_find_mode(imx214->fmt.height);
>
> You're calling this function a few times, could you consider caching
> mode instead? Or does it make your code mode complex?

I prefer to keep it this way. The mode can be computed with other
fields of the structure and the computation is really easy. If in the
future it requires a more complex calculation I will cache the result.

>
> > +
> > + ret = imx214_write_table(imx214, mode_table_common);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "could not sent common table %d\n",
> > + ret);
> > + return ret;
> > + }
> > + ret = imx214_write_table(imx214, imx214_modes[mode].reg_table);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "could not sent mode table %d\n",
> > + ret);
> > + return ret;
> > + }
> > + ret = v4l2_ctrl_handler_setup(&imx214->ctrls);
>
> is it fine to call this multiple times, at streamon time?

I guess so, maybe Hans can clarify it. It is used in:
mt9m111.c,
ov7740.c

I liked the idea and I copied it. But right now it could be removed completely.
If/when I add gain/exposure we can rethink about it.

>
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "could not sync v4l2 controls\n");
> > + return ret;
> > + }
> > + ret = regmap_write(imx214->regmap, 0x100, 1);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "could not sent start table %d\n",
> > + ret);
> > + return ret;
> > + }
> > + } else {
> > + ret = regmap_write(imx214->regmap, 0x100, 0);
> > + if (ret < 0) {
> > + dev_err(imx214->dev, "could not sent stop table %d\n",
> > + ret);
> > + return ret;
> > + }
> > + }
> > +
> > + return 0;
> > +}
> > +
> > +static int imx214_g_frame_interval(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_frame_interval *fival)
> > +{
> > + fival->pad = 0;
> > + fival->interval.numerator = 1;
> > + fival->interval.denominator = IMX214_FPS;
> > +
> > + return 0;
> > +}
> > +
> > +static int imx214_enum_frame_interval(struct v4l2_subdev *subdev,
> > + struct v4l2_subdev_pad_config *cfg,
> > + struct v4l2_subdev_frame_interval_enum *fie)
> > +{
> > + int mode;
> > +
> > + if (fie->index != 0)
> > + return -EINVAL;
> > +
> > + mode = imx214_find_mode(fie->height);
> > +
> > + fie->code = IMX214_MBUS_CODE;
> > + fie->width = imx214_modes[mode].width;
> > + fie->height = imx214_modes[mode].height;
> > + fie->interval.numerator = 1;
> > + fie->interval.denominator = IMX214_MBUS_CODE;
>
> denominator = MBUS_CODE ?
>
> > +
> > + return 0;
> > +}
> > +
> > +static const struct v4l2_subdev_video_ops imx214_video_ops = {
> > + .s_stream = imx214_s_stream,
> > + .g_frame_interval = imx214_g_frame_interval,
> > + .s_frame_interval = imx214_g_frame_interval,
> > +};
> > +
> > +static const struct v4l2_subdev_pad_ops imx214_subdev_pad_ops = {
> > + .enum_mbus_code = imx214_enum_mbus_code,
> > + .enum_frame_size = imx214_enum_frame_size,
> > + .enum_frame_interval = imx214_enum_frame_interval,
> > + .get_fmt = imx214_get_format,
> > + .set_fmt = imx214_set_format,
> > + .get_selection = imx214_get_selection,
> > + .init_cfg = imx214_entity_init_cfg,
> > +};
> > +
> > +static const struct v4l2_subdev_ops imx214_subdev_ops = {
> > + .core = &imx214_core_ops,
> > + .video = &imx214_video_ops,
> > + .pad = &imx214_subdev_pad_ops,
> > +};
> > +
> > +static const struct regmap_config sensor_regmap_config = {
> > + .reg_bits = 16,
> > + .val_bits = 8,
> > + .cache_type = REGCACHE_RBTREE,
> > +};
> > +
> > +static int imx214_get_regulators(struct device *dev, struct imx214 *imx214)
> > +{
> > + int i;
> > +
> > + for (i = 0; i < IMX214_NUM_SUPPLIES; i++)
> > + imx214->supplies[i].supply = imx214_supply_name[i];
> > +
> > + return devm_regulator_bulk_get(dev,
> > + IMX214_NUM_SUPPLIES,
> > + imx214->supplies);
> > +}
> > +
> > +static int imx214_probe(struct i2c_client *client)
> > +{
> > + struct device *dev = &client->dev;
> > + struct imx214 *imx214;
> > + struct fwnode_handle *endpoint;
> > + int ret;
> > + static const s64 link_freq[] = {
> > + (IMX214_DEFAULT_PIXEL_RATE * 10LL) / 8,
> > + };
> > +
> > + imx214 = devm_kzalloc(dev, sizeof(*imx214), GFP_KERNEL);
> > + if (!imx214)
> > + return -ENOMEM;
> > +
> > + imx214->dev = dev;
> > +
> > + endpoint = fwnode_graph_get_next_endpoint(
> > + of_fwnode_handle(client->dev.of_node), NULL);
> > + if (!endpoint) {
> > + dev_err(dev, "endpoint node not found\n");
> > + return -EINVAL;
> > + }
> > +
> > + ret = v4l2_fwnode_endpoint_parse(endpoint, &imx214->ep);
>
> is imx214->ep used anywhere else apart from probe? can it just be a
> variable local to this function?
>
> > + fwnode_handle_put(endpoint);
> > + if (ret < 0) {
> > + dev_err(dev, "parsing endpoint node failed\n");
> > + return ret;
> > + }
> > +
> > + if (imx214->ep.bus_type != V4L2_MBUS_CSI2) {
> > + dev_err(dev, "invalid bus type (%u), must be CSI2 (%u)\n",
> > + imx214->ep.bus_type, V4L2_MBUS_CSI2);
> > + return -EINVAL;
> > + }
> > +
> > + imx214->xclk = devm_clk_get(dev, "xclk");
> > + if (IS_ERR(imx214->xclk)) {
> > + dev_err(dev, "could not get xclk");
> > + return PTR_ERR(imx214->xclk);
> > + }
> > +
> > + ret = clk_set_rate(imx214->xclk, IMX214_DEFAULT_CLK_FREQ);
> > + if (ret) {
> > + dev_err(dev, "could not set xclk frequency\n");
> > + return ret;
> > + }
> > +
> > + ret = imx214_get_regulators(dev, imx214);
> > + if (ret < 0) {
> > + dev_err(dev, "cannot get regulators\n");
> > + return ret;
> > + }
> > +
> > + imx214->enable_gpio = devm_gpiod_get(dev, "enable", GPIOD_OUT_LOW);
> > + if (IS_ERR(imx214->enable_gpio)) {
> > + dev_err(dev, "cannot get enable gpio\n");
> > + return PTR_ERR(imx214->enable_gpio);
> > + }
> > +
> > + imx214->regmap = devm_regmap_init_i2c(client, &sensor_regmap_config);
> > + if (IS_ERR(imx214->regmap)) {
> > + dev_err(dev, "regmap init failed\n");
> > + return PTR_ERR(imx214->regmap);
> > + }
> > +
> > + v4l2_ctrl_handler_init(&imx214->ctrls, 2);
> > +
> > + imx214->pixel_rate = v4l2_ctrl_new_std(&imx214->ctrls, NULL,
> > + V4L2_CID_PIXEL_RATE, 0,
> > + IMX214_DEFAULT_PIXEL_RATE, 1,
> > + IMX214_DEFAULT_PIXEL_RATE);
>
> Is it fine not to provide a ctrl_ops structure to read/write controls?

I believe so. Hans, is this ok?

>
> Thanks
> j
>
> > + imx214->link_freq = v4l2_ctrl_new_int_menu(&imx214->ctrls, NULL,
> > + V4L2_CID_LINK_FREQ,
> > + ARRAY_SIZE(link_freq) - 1,
> > + 0, link_freq);
> > + if (imx214->link_freq)
> > + imx214->link_freq->flags |= V4L2_CTRL_FLAG_READ_ONLY;
> > + ret = imx214->ctrls.error;
> > + if (ret) {
> > + dev_err(&client->dev, "%s control init failed (%d)\n",
> > + __func__, ret);
> > + goto free_ctrl;
> > + }
> > +
> > + imx214->sd.ctrl_handler = &imx214->ctrls;
> > + ret = v4l2_ctrl_handler_setup(imx214->sd.ctrl_handler);
> > + if (ret) {
> > + dev_err(&client->dev,
> > + "Error %d setting default controls\n", ret);
> > + goto free_ctrl;
> > + }
> > +
> > + v4l2_i2c_subdev_init(&imx214->sd, client, &imx214_subdev_ops);
> > + imx214->sd.flags |= V4L2_SUBDEV_FL_HAS_DEVNODE;
> > + imx214->pad.flags = MEDIA_PAD_FL_SOURCE;
> > + imx214->sd.dev = &client->dev;
> > + imx214->sd.entity.function = MEDIA_ENT_F_CAM_SENSOR;
> > +
> > + ret = media_entity_pads_init(&imx214->sd.entity, 1, &imx214->pad);
> > + if (ret < 0) {
> > + dev_err(dev, "could not register media entity\n");
> > + goto free_ctrl;
> > + }
> > +
> > + imx214_entity_init_cfg(&imx214->sd, NULL);
> > +
> > + ret = v4l2_async_register_subdev_sensor_common(&imx214->sd);
> > + if (ret < 0) {
> > + dev_err(dev, "could not register v4l2 device\n");
> > + goto free_entity;
> > + }
> > +
> > + return 0;
> > +
> > +free_entity:
> > + media_entity_cleanup(&imx214->sd.entity);
> > +free_ctrl:
> > + v4l2_ctrl_handler_free(&imx214->ctrls);
> > +
> > + return ret;
> > +}
> > +
> > +static int imx214_remove(struct i2c_client *client)
> > +{
> > + struct v4l2_subdev *sd = i2c_get_clientdata(client);
> > + struct imx214 *imx214 = to_imx214(sd);
> > +
> > + v4l2_async_unregister_subdev(&imx214->sd);
> > + media_entity_cleanup(&imx214->sd.entity);
> > + v4l2_ctrl_handler_free(&imx214->ctrls);
> > +
> > + return 0;
> > +}
> > +
> > +static const struct of_device_id imx214_of_match[] = {
> > + { .compatible = "sony,imx214" },
> > + { }
> > +};
> > +MODULE_DEVICE_TABLE(of, imx214_of_match);
> > +
> > +static struct i2c_driver imx214_i2c_driver = {
> > + .driver = {
> > + .of_match_table = imx214_of_match,
> > + .name = "imx214",
> > + },
> > + .probe_new = imx214_probe,
> > + .remove = imx214_remove,
> > +};
> > +
> > +module_i2c_driver(imx214_i2c_driver);
> > +
> > +MODULE_DESCRIPTION("Sony IMX214 Camera drier");
> > +MODULE_AUTHOR("Ricardo Ribalda <ricardo.ribalda@xxxxxxxxx>");
> > +MODULE_LICENSE("GPL v2");
> > --
> > 2.18.0
> >



--
Ricardo Ribalda