Re: [PATCH RFT] net: dsa: Allow configuring CPU port VLANs

From: Ilias Apalodimas
Date: Tue Aug 28 2018 - 04:33:07 EST


On Fri, Aug 10, 2018 at 04:58:10PM -0700, Florian Fainelli wrote:
> On 06/25/2018 02:17 AM, Ilias Apalodimas wrote:
> > On Mon, Jun 25, 2018 at 12:13:10PM +0300, Petr Machata wrote:
> >> Florian Fainelli <f.fainelli@xxxxxxxxx> writes:
> >>
> >>> if (netif_is_bridge_master(vlan->obj.orig_dev))
> >>> - return -EOPNOTSUPP;
> >>> + info.port = dp->cpu_dp->index;
> >>
> >> The condition above will trigger also when a VLAN is added on a member
> >> port, and there's no other port with that VLAN. In that case the VLAN
> >> comes without the BRIDGE_VLAN_INFO_BRENTRY flag. In mlxsw we have this
> >> to get the bridge VLANs:
> >>
> >> if (netif_is_bridge_master(orig_dev)) {
> >> [...]
> >> if ((vlan->flags & BRIDGE_VLAN_INFO_BRENTRY) &&
> >> [...]
> >>
> >> This doesn't appear to be done in DSA unless I'm missing something.
> > Petr's right. This will trigger for VLANs added on 'not cpu ports' if the VLAN
> > is not already a member.
> >
> > This command has BRIDGE_VLAN_INFO_BRENTRY set:
> > bridge vlan add dev br0 vid 100 pvid untagged self
> > I had the same issue on my CPSW RFC and solved it
> > exactly the same was as Petr suggested.
>
> Humm, there must be something obvious I am missing, but the following
> don't exactly result in what I would expect after adding a check for
> vlan->flags & BRIDGE_VLAN_INFO_BRENTRY:
>
> brctl addbr br0
> echo 1 > /sys/class/net/br0/bridge/vlan_filtering
> brctl addif br0 lan1
>
> #1 results in lan1 being programmed with VID 1, PVID, untagged, but not
> the CPU port. I would have sort of expected that the bridge layer would
> also push the configuration to br0/CPU port since this is the default VLAN:
>
> bridge vlan show dev br0
> port vlan ids
> br0 1 PVID Egress Untagged
>
> But it does not.
>
> bridge vlan add vid 2 dev lan1
>
> #2 same thing, results in only lan1 being programmed with VID 2, tagged
> but that is expected because we are creating the VLAN only for the
> user-facing port.
>
> bridge vlan add vid 3 dev br0 self
>
> #3 results in the CPU port being programmed with VID 3, tagged, again,
> this is expected because we are only programming the bridge master/CPU
> port here.
>
> Does #1 also happen for cpsw and mlxsw or do you actually get events
> about the bridge's default VLAN configuration? Or does the switch driver
> actually need to obtain that at the time the port is enslaved somehow?
As long as ports are attached you get the events (one event per attached port
iirc)
if the event is checked against BRIDGE_VLAN_INFO_BRENTRY, the only way to add a
VLAN to the cpu port is via 'bridge vlan add vid 3 dev br0 self'
>
> Thanks!
> --
> Florian
/Ilias