Re: [PATCH v4 15/35] mtd: rawnand: mxc: convert driver to nand_scan()

From: Boris Brezillon
Date: Sat Jul 21 2018 - 13:19:22 EST


On Fri, 20 Jul 2018 17:15:07 +0200
Miquel Raynal <miquel.raynal@xxxxxxxxxxx> wrote:

> Two helpers have been added to the core to make ECC-related
> configuration between the detection phase and the final NAND scan. Use
> these hooks and convert the driver to just use nand_scan() instead of
> both nand_scan_ident() and nand_scan_tail().
>
> Signed-off-by: Miquel Raynal <miquel.raynal@xxxxxxxxxxx>

Reviewed-by: Boris Brezillon <boris.brezillon@xxxxxxxxxxx>

> ---
> drivers/mtd/nand/raw/mxc_nand.c | 136 +++++++++++++++++++++-------------------
> 1 file changed, 71 insertions(+), 65 deletions(-)
>
> diff --git a/drivers/mtd/nand/raw/mxc_nand.c b/drivers/mtd/nand/raw/mxc_nand.c
> index c6eff61e909d..4c9214dea424 100644
> --- a/drivers/mtd/nand/raw/mxc_nand.c
> +++ b/drivers/mtd/nand/raw/mxc_nand.c
> @@ -1691,6 +1691,74 @@ static int mxcnd_probe_dt(struct mxc_nand_host *host)
> }
> #endif
>
> +static int mxcnd_attach_chip(struct nand_chip *chip)
> +{
> + struct mtd_info *mtd = nand_to_mtd(chip);
> + struct mxc_nand_host *host = nand_get_controller_data(chip);
> + struct device *dev = mtd->dev.parent;
> +
> + switch (chip->ecc.mode) {
> + case NAND_ECC_HW:
> + chip->ecc.read_page = mxc_nand_read_page;
> + chip->ecc.read_page_raw = mxc_nand_read_page_raw;
> + chip->ecc.read_oob = mxc_nand_read_oob;
> + chip->ecc.write_page = mxc_nand_write_page_ecc;
> + chip->ecc.write_page_raw = mxc_nand_write_page_raw;
> + chip->ecc.write_oob = mxc_nand_write_oob;
> + break;
> +
> + case NAND_ECC_SOFT:
> + break;
> +
> + default:
> + return -EINVAL;
> + }
> +
> + if (chip->bbt_options & NAND_BBT_USE_FLASH) {
> + chip->bbt_td = &bbt_main_descr;
> + chip->bbt_md = &bbt_mirror_descr;
> + }
> +
> + /* Allocate the right size buffer now */
> + devm_kfree(dev, (void *)host->data_buf);
> + host->data_buf = devm_kzalloc(dev, mtd->writesize + mtd->oobsize,
> + GFP_KERNEL);
> + if (!host->data_buf)
> + return -ENOMEM;
> +
> + /* Call preset again, with correct writesize chip time */
> + host->devtype_data->preset(mtd);
> +
> + if (!chip->ecc.bytes) {
> + if (host->eccsize == 8)
> + chip->ecc.bytes = 18;
> + else if (host->eccsize == 4)
> + chip->ecc.bytes = 9;
> + }
> +
> + /*
> + * Experimentation shows that i.MX NFC can only handle up to 218 oob
> + * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare()
> + * into copying invalid data to/from the spare IO buffer, as this
> + * might cause ECC data corruption when doing sub-page write to a
> + * partially written page.
> + */
> + host->used_oobsize = min(mtd->oobsize, 218U);
> +
> + if (chip->ecc.mode == NAND_ECC_HW) {
> + if (is_imx21_nfc(host) || is_imx27_nfc(host))
> + chip->ecc.strength = 1;
> + else
> + chip->ecc.strength = (host->eccsize == 4) ? 4 : 8;
> + }
> +
> + return 0;
> +}
> +
> +static const struct nand_controller_ops mxcnd_controller_ops = {
> + .attach_chip = mxcnd_attach_chip,
> +};
> +
> static int mxcnd_probe(struct platform_device *pdev)
> {
> struct nand_chip *this;
> @@ -1830,71 +1898,9 @@ static int mxcnd_probe(struct platform_device *pdev)
> host->devtype_data->irq_control(host, 1);
> }
>
> - /* first scan to find the device and get the page size */
> - err = nand_scan_ident(mtd, is_imx25_nfc(host) ? 4 : 1, NULL);
> - if (err)
> - goto escan;
> -
> - switch (this->ecc.mode) {
> - case NAND_ECC_HW:
> - this->ecc.read_page = mxc_nand_read_page;
> - this->ecc.read_page_raw = mxc_nand_read_page_raw;
> - this->ecc.read_oob = mxc_nand_read_oob;
> - this->ecc.write_page = mxc_nand_write_page_ecc;
> - this->ecc.write_page_raw = mxc_nand_write_page_raw;
> - this->ecc.write_oob = mxc_nand_write_oob;
> - break;
> -
> - case NAND_ECC_SOFT:
> - break;
> -
> - default:
> - err = -EINVAL;
> - goto escan;
> - }
> -
> - if (this->bbt_options & NAND_BBT_USE_FLASH) {
> - this->bbt_td = &bbt_main_descr;
> - this->bbt_md = &bbt_mirror_descr;
> - }
> -
> - /* allocate the right size buffer now */
> - devm_kfree(&pdev->dev, (void *)host->data_buf);
> - host->data_buf = devm_kzalloc(&pdev->dev, mtd->writesize + mtd->oobsize,
> - GFP_KERNEL);
> - if (!host->data_buf) {
> - err = -ENOMEM;
> - goto escan;
> - }
> -
> - /* Call preset again, with correct writesize this time */
> - host->devtype_data->preset(mtd);
> -
> - if (!this->ecc.bytes) {
> - if (host->eccsize == 8)
> - this->ecc.bytes = 18;
> - else if (host->eccsize == 4)
> - this->ecc.bytes = 9;
> - }
> -
> - /*
> - * Experimentation shows that i.MX NFC can only handle up to 218 oob
> - * bytes. Limit used_oobsize to 218 so as to not confuse copy_spare()
> - * into copying invalid data to/from the spare IO buffer, as this
> - * might cause ECC data corruption when doing sub-page write to a
> - * partially written page.
> - */
> - host->used_oobsize = min(mtd->oobsize, 218U);
> -
> - if (this->ecc.mode == NAND_ECC_HW) {
> - if (is_imx21_nfc(host) || is_imx27_nfc(host))
> - this->ecc.strength = 1;
> - else
> - this->ecc.strength = (host->eccsize == 4) ? 4 : 8;
> - }
> -
> - /* second phase scan */
> - err = nand_scan_tail(mtd);
> + /* Scan the NAND device */
> + this->dummy_controller.ops = &mxcnd_controller_ops;
> + err = nand_scan(mtd, is_imx25_nfc(host) ? 4 : 1);
> if (err)
> goto escan;
>