Re: FW: [PATCH 2/2] ath10k: allow ATH10K_SNOC with COMPILE_TEST

From: Niklas Cassel
Date: Thu Jun 14 2018 - 14:43:00 EST


On Thu, Jun 14, 2018 at 05:09:04PM +0300, Kalle Valo wrote:
> Niklas Cassel <niklas.cassel@xxxxxxxxxx> writes:
>
> > On Tue, Jun 12, 2018 at 02:44:03PM +0200, Niklas Cassel wrote:
> >> On Tue, Jun 12, 2018 at 06:02:48PM +0530, Govind Singh wrote:
> >> > On 2018-06-12 17:45, Govind Singh wrote:
> >> > >
> >> > > ATH10K_SNOC builds just fine with COMPILE_TEST, so make that possible.
> >> > >
> >> > > Signed-off-by: Niklas Cassel <niklas.cassel@xxxxxxxxxx>
> >> > > ---
> >> > > drivers/net/wireless/ath/ath10k/Kconfig | 3 ++-
> >> > > 1 file changed, 2 insertions(+), 1 deletion(-)
> >> > >
> >> > > diff --git a/drivers/net/wireless/ath/ath10k/Kconfig
> >> > > b/drivers/net/wireless/ath/ath10k/Kconfig
> >> > > index 54ff5930126c..6572a43590a8 100644
> >> > > --- a/drivers/net/wireless/ath/ath10k/Kconfig
> >> > > +++ b/drivers/net/wireless/ath/ath10k/Kconfig
> >> > > @@ -42,7 +42,8 @@ config ATH10K_USB
> >> > >
> >> > > config ATH10K_SNOC
> >> > > tristate "Qualcomm ath10k SNOC support (EXPERIMENTAL)"
> >> > > - depends on ATH10K && ARCH_QCOM
> >> > > + depends on ATH10K
> >> > > + depends on ARCH_QCOM || COMPILE_TEST
> >> > > ---help---
> >> > > This module adds support for integrated WCN3990 chip connected
> >> > > to system NOC(SNOC). Currently work in progress and will not
> >> >
> >> > Thanks Niklas for enabling COMPILE_TEST. With QMI set of
> >> > changes(https://patchwork.kernel.org/patch/10448183/), we need to enable
> >> > COMPILE_TEST for
> >> > QCOM_SCM/QMI_HELPERS which seems broken today. Are you planning to fix the
> >> > same.
> >
> > This patch is good as is.
> >
> > However, Govind's QMI patch set together with this patch
> > resulted in build errors.
> >
> > FTR, these are fixed by:
> > https://marc.info/?l=linux-kernel&m=152880985402356
> > https://marc.info/?l=linux-kernel&m=152889452326350
>
> So the problem is that if I apply this patch I can't apply Govind's QMI
> patchset (due to the build problems) until Niklas' fixes to qcom and
> rpmsg subsystems propogate back to my tree and that might take weeks, or
> even months. But I really would like to apply the QMI patchset ASAP so
> that we can complete the wcn3990 support and not unnecessarily delay it.
>
> So what I propose is that I put this patch 2 as 'Awaiting Upstream' in
> patchwork and apply it once Niklas' patches get to my tree. Does that
> sound good?

Absolutely.

I didn't realize this until after sending the patch.


Kind regards,
Niklas