Re: [PATCH] Bluetooth: hci_bcm: Configure SCO routing automatically

From: Rob Herring
Date: Mon Jun 11 2018 - 15:05:56 EST


On Mon, Jun 11, 2018 at 12:19 PM, Marcel Holtmann <marcel@xxxxxxxxxxxx> wrote:
> Hi Rob,
>
>>>>>>> Added support to automatically configure the SCO packet routing at the
>>>>>>> device setup. The SCO packets are used with the HSP / HFP profiles, but in
>>>>>>> some devices (ex. CYW43438) they are routed to a PCM output by default. This
>>>>>>> change allows sending the vendor specific HCI command to configure the SCO
>>>>>>> routing. The parameters of the command are loaded from the device tree.
>>>>>>
>>>>>> Please wrap your commit msg.
>>>>>
>>>>>
>>>>> Sure.
>>>>>>
>>>>>>
>>>>>>>
>>>>>>> Signed-off-by: Attila TÅkÃs <attitokes@xxxxxxxxx>
>>>>>>> ---
>>>>>>> .../bindings/net/broadcom-bluetooth.txt | 7 ++
>>>>>>
>>>>>> Please split bindings to separate patch.
>>>>>
>>>>>
>>>>> Ok, I will split this in two.
>>>>>>
>>>>>>
>>>>>>
>>>>>>
>>>>>>> drivers/bluetooth/hci_bcm.c | 72 +++++++++++++++++++
>>>>>>> 2 files changed, 79 insertions(+)
>>>>>>>
>>>>>>> diff --git
>>>>>>> a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>>>>> b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>>>>> index 4194ff7e..aea3a094 100644
>>>>>>> --- a/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>>>>> +++ b/Documentation/devicetree/bindings/net/broadcom-bluetooth.txt
>>>>>>> @@ -21,6 +21,12 @@ Optional properties:
>>>>>>> - clocks: clock specifier if external clock provided to the controller
>>>>>>> - clock-names: should be "extclk"
>>>>>>>
>>>>>>> + SCO routing parameters:
>>>>>>> + - sco-routing: 0-3 (PCM, Transport, Codec, I2S)
>>>>>>> + - pcm-interface-rate: 0-4 (128 Kbps - 2048 Kbps)
>>>>>>> + - pcm-frame-type: 0 (short), 1 (long)
>>>>>>> + - pcm-sync-mode: 0 (slave), 1 (master)
>>>>>>> + - pcm-clock-mode: 0 (slave), 1 (master)
>>>>>>
>>>>>> Are these Broadcom specific? Properties need either vendor prefix or
>>>>>> to be documented in a common location. I think these look like the
>>>>>> latter.
>>>>>
>>>>>
>>>>> These will be used as parameters of a vendor specific (Broadcom/Cypress)
>>>>> command configuring the SCO packet routing. See the Write_SCO_PCM_Int_Param
>>>>> command from: http://www.cypress.com/file/298311/download.
>>>>
>>>> The DT should just describe how the h/w is hooked-up. What the s/w has
>>>> to do based on that is the driver's problem which is certainly
>>>> vendor/chip specific, but that is all irrelevant to the binding.
>>>>
>>>>> What would be the property names with a Broadcom / Cypress vendor prefix?
>>>>>
>>>>> brcm,sco-routing
>>>>> brcm,pcm-interface-rate
>>>>> brcm,pcm-frame-type
>>>>> brcm,pcm-sync-mode
>>>>> brcm,pcm-clock-mode
>>>>>
>>>>> ?
>>>>
>>>> Yes.
>>>
>>> we can do this. However all pcm-* are optional if you switch the HCI transport. And sco-routing should default to HCI if that is not present. Meaning a driver should actively trying to change this. Nevertheless, it would be good if a driver reads the current settings.
>>>
>>> In theory we could make sco-routing generic, but so many vendors have different modes, that we better keep this vendor specific.
>>
>> Even if vendor specific, the properties for not HCI transport case are
>> still incomplete IMO.
>>
>> By modes, you mean PCM vs. I2S and all the flavors of timings you can
>> have within those or something else? For the former, that's often
>> going to be a process of solving what each end support and if that
>> doesn't work, then IIRC we already have properties for setting
>> modes/timing. All the same issues exist with audio codecs and this is
>> really not any different.
>
> this is what Broadcom uses to configure their PCM transport. So I think for now, we make them brcm, specific and see how that goes. We can always generalize them later if enough chip manufactures provide support for it.

We already have properties doing the same thing defined in
Documentation/devicetree/bindings/sound/simple-card.txt. Use and
extend that. We don't need new properties especially for something
that is not complete. For example If I have 2 host ports (every SoC
has at least 2), how do I indicate which one is connected to BT.

Rob