Re: [PATCH v3] Input: add bu21029 touch driver

From: Andy Shevchenko
Date: Sun May 13 2018 - 11:06:58 EST


On Fri, May 11, 2018 at 5:22 PM, Mark Jonas <mark.jonas@xxxxxxxxxxxx> wrote:

> Add Rohm BU21029 resistive touch panel controller support with I2C
> interface.

> +#include <linux/of.h>

This becomes redundant (see below).

> +#define STOP_DELAY_US 50L
> +#define START_DELAY_MS 2L
> +#define BUF_LEN 8L

No need to use L for such small numbers. Integer promotion is a part
of C standard.

> +#define SCALE_12BIT (1 << 12)
> +#define MAX_12BIT ((1 << 12) - 1)

BIT(12)
GENMASK(11, 0)

> +static int bu21029_touch_report(struct bu21029_ts_data *bu21029)
> +{
> + struct i2c_client *i2c = bu21029->client;
> + u8 buf[BUF_LEN];
> + int error = bu21029_touch_report(bu21029);

> +

Redundant empty line.

> + if (error) {

> + dev_err(&i2c->dev, "failed to report (error: %d)\n", error);

Potential spamming case.

> + return IRQ_NONE;
> + }

> +static void bu21029_stop_chip(struct input_dev *dev)
> +{
> + struct bu21029_ts_data *bu21029 = input_get_drvdata(dev);
> +
> + disable_irq(bu21029->client->irq);
> + del_timer_sync(&bu21029->timer);
> +
> + /* put chip into reset */
> + gpiod_set_value_cansleep(bu21029->reset_gpios, 1);

> + udelay(STOP_DELAY_US);

udelay() ?!

> +}
> +

> +static int bu21029_start_chip(struct input_dev *dev)
> +{

> + u16 hwid;
> +
> + /* take chip out of reset */
> + gpiod_set_value_cansleep(bu21029->reset_gpios, 0);

> + mdelay(START_DELAY_MS);

mdelay()?!

> +
> + error = i2c_smbus_read_i2c_block_data(i2c,
> + BU21029_HWID_REG,
> + 2,
> + (u8 *)&hwid);
> + if (error < 0) {
> + dev_err(&i2c->dev, "failed to read HW ID\n");
> + goto out;
> + }
> +

> + if (cpu_to_be16(hwid) != SUPPORTED_HWID) {

Hmm... Why cpu_to_be16() is required?

> + dev_err(&i2c->dev, "unsupported HW ID 0x%x\n", hwid);
> + error = -ENODEV;
> + goto out;
> + }
> +}

> +static int bu21029_parse_dt(struct bu21029_ts_data *bu21029)

You can get rid of DT requirement by...

> +{
> + struct device *dev = &bu21029->client->dev;
> + struct device_node *np = dev->of_node;
> + u32 val32;
> + int error;

> + if (!np) {
> + dev_err(dev, "no device tree data\n");
> + return -EINVAL;
> + }

(this becomes redundant)

> +
> + bu21029->reset_gpios = devm_gpiod_get(dev, "reset", GPIOD_OUT_HIGH);
> + if (IS_ERR(bu21029->reset_gpios)) {
> + error = PTR_ERR(bu21029->reset_gpios);
> + if (error != -EPROBE_DEFER)
> + dev_err(dev, "invalid 'reset-gpios':%d\n", error);
> + return error;
> + }
> +

> + if (of_property_read_u32(np, "rohm,x-plate-ohms", &val32)) {

...simple calling device_property_read_u32() instead.

> + dev_err(dev, "invalid 'x-plate-ohms' supplied\n");
> + return -EINVAL;
> + }
> + bu21029->x_plate_ohms = val32;
> +
> + touchscreen_parse_properties(bu21029->in_dev, false, &bu21029->prop);
> +
> + return 0;
> +}

> +#ifdef CONFIG_PM_SLEEP

Instead...

> +static int bu21029_suspend(struct device *dev)

...use __maby_unused annotation.

> +static int bu21029_resume(struct device *dev)

Ditto.

--
With Best Regards,
Andy Shevchenko