Re: [PATCHv4 09/10] dt-bindings: mfd: ti-lmu: update for backlight

From: Sebastian Reichel
Date: Mon Apr 09 2018 - 17:24:32 EST


Hi,

On Mon, Apr 09, 2018 at 04:06:38PM -0500, Rob Herring wrote:
> On Fri, Mar 30, 2018 at 07:24:13PM +0200, Sebastian Reichel wrote:
> > Update binding to integrate the backlight feature directly into
> > the main node, as suggested by Rob Herring.
> >
> > Signed-off-by: Sebastian Reichel <sebastian.reichel@xxxxxxxxxxxxxxx>
> > ---
> > Documentation/devicetree/bindings/mfd/ti-lmu.txt | 119 ++++++++++++-----------
> > 1 file changed, 60 insertions(+), 59 deletions(-)
> >
> > diff --git a/Documentation/devicetree/bindings/mfd/ti-lmu.txt b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > index c885cf89b8ce..b3433e95dfa5 100644
> > --- a/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > +++ b/Documentation/devicetree/bindings/mfd/ti-lmu.txt
> > @@ -28,10 +28,9 @@ Required properties:
> >
> > Optional property:
> > - enable-gpios: A GPIO specifier for hardware enable pin.
> > -
> > -Required node:
> > - - backlight: All LMU devices have backlight child nodes.
> > - For the properties, please refer to [1].
> > + - pwm-names: Should be either "lmu-backlight" or unset
> > + - pwm: This should be a PWM specifier following ../pwm/pwm.txt and must
> > + only be specified, if the backlight should be used in PWM mode.
> >
> > Optional nodes:
> > - fault-monitor: Hardware fault monitoring driver for LM3633 and LM3697.
> > @@ -42,8 +41,31 @@ Optional nodes:
> > - leds: LED properties for LM3633. Please refer to [2].
> > - regulators: Regulator properties for LM3631 and LM3632.
> > Please refer to [3].
> > + - bank0, bank1, bank2: This contains the backlight configuration
> > + for each backlight control bank.
> > +
> > +Required properties in the bank subnodes:
> > + - label: A string describing the backlight. Should contain "keyboard"
> > + for a keyboard backlight and "lcd" for LCD panel backlights.
> > + - ti,led-sources: A list of channels, that should be driven. Each channel
> > + should only be driven by one bank.
> > +
> > +Optional properties in the bank subnodes:
> > + - default-brightness-level: Backlight initial brightness value.
> > + Type is <u32>. It is set as soon as backlight
> > + device is created.
> > + 0 ~ 2047 = LM3631, LM3632, LM3633, LM3695 and
> > + LM3697
> > + 0 ~ 255 = LM3532
> > + - ti,ramp-up-ms, ti,ramp-down-ms: Light dimming effect properties.
> > + Type is <u32>. Unit is millisecond.
> > + 0 ~ 65 ms = LM3532
> > + 0 ~ 4000 ms = LM3631
> > + 0 ~ 16000 ms = LM3633 and LM3697
> > + - pwm-period: PWM period. Only valid in PWM brightness mode.
> > + Type is <u32>. If this property is missing, then control
> > + mode is set to I2C by default.
> >
> > -[1] ../leds/backlight/ti-lmu-backlight.txt
> > [2] ../leds/leds-lm3633.txt
> > [3] ../regulator/lm363x-regulator.txt
> >
> > @@ -53,14 +75,11 @@ lm3532@38 {
> >
> > enable-gpios = <&pioC 2 GPIO_ACTIVE_HIGH>;
> >
> > - backlight {
> > - compatible = "ti,lm3532-backlight";
> > -
> > - lcd {
> > - led-sources = <0 1 2>;
> > - ramp-up-msec = <30>;
> > - ramp-down-msec = <0>;
> > - };
> > + bank0 {
> > + label = "lcd";
> > + led-sources = <0 1 2>;
> > + ramp-up-msec = <30>;
> > + ramp-down-msec = <0>;
>
> Looks like it was already wrong, but these are missing the vendor
> prefixes.

Oops. I will add the vendor prefix.

>
> > };
> > };
> >
> > @@ -105,13 +124,10 @@ lm3631@29 {
>
> Are so many examples really needed? Examples aren't supposed to
> enumerate all possible options...

I will remove a few in the next version.

-- Sebastian

Attachment: signature.asc
Description: PGP signature