Re: [PATCH] iio: chemical: ccs811: Corrected firmware boot/application mode transition

From: Jonathan Cameron
Date: Sat Feb 17 2018 - 09:25:41 EST


On Wed, 14 Feb 2018 22:02:36 +0000
Richard Lai <richard@xxxxxxxxxxxxxx> wrote:

> CCS811 has different I2C register maps in boot and application mode. When
> CCS811 is in boot mode, register APP_START (0xF4) is used to transit the
> firmware state from boot to application mode. However, APP_START is not a
> valid register location when CCS811 is in application mode (refer to
> "CCS811 Bootloader Register Map" and "CCS811 Application Register Map" in
> CCS811 datasheet). The driver should not attempt to perform a write to
> APP_START while CCS811 is in application mode, as this is not a valid or
> documented register location.
>
> When prob function is being called, the driver assumes the CCS811 sensor
> is in boot mode, and attempts to perform a write to APP_START. Although
> CCS811 powers-up in boot mode, it may have already been transited to
> application mode by previous instances, e.g. unload and reload device
> driver by the system, or explicitly by user. Depending on the system
> design, CCS811 sensor may be permanently connected to system power source
> rather than power controlled by GPIO, hence it is possible that the sensor
> is never power reset, thus the firmware could be in either boot or
> application mode at any given time when driver prob function is being
> called.
>
> This patch:
>
> 1) Checks the STATUS register before attempting to send a write to
> APP_START. Only if the firmware is not in application mode and has
> valid firmware application loaded, then it will continue to start
> transiting the firmware boot to application mode.
> 2) Adds two macros for checking APP_VALID and FW_MODE bits in the STATUS
> register of CCS811 sensor.
>
> Signed-off-by: Richard Lai <richard@xxxxxxxxxxxxxx>

Comment inline + again, want to allow time for other comments.

> ---
> drivers/iio/chemical/ccs811.c | 14 ++++++++++----
> 1 file changed, 10 insertions(+), 4 deletions(-)
>
> diff --git a/drivers/iio/chemical/ccs811.c b/drivers/iio/chemical/ccs811.c
> index 840a6cb..4806aed 100644
> --- a/drivers/iio/chemical/ccs811.c
> +++ b/drivers/iio/chemical/ccs811.c
> @@ -52,6 +52,11 @@
> #define CCS811_STATUS_FW_MODE_MASK BIT(7)
> #define CCS811_STATUS_FW_MODE_APPLICATION BIT(7)
>
> +#define IS_APP_VALID_LOADED(x) \
> + (CCS811_STATUS_APP_VALID_LOADED == (CCS811_STATUS_APP_VALID_MASK & x))
> +#define IS_FW_MODE_APPLICATION(x) \
> + (CCS811_STATUS_FW_MODE_APPLICATION == (CCS811_STATUS_FW_MODE_MASK & x))
> +
This driver has the slightly unusual separation for single bit fields into
mask and value. I'm not sure what benefit that actually has the effect
of making these macros more complex than we would normally expect.

If we drop the masks, then we have simply
#define IS_FW_MODE_APPLICATION(x) \
(x & CCS811_STATUS_FW_MODE_APPLICATION).

At that point the macro adds little over directly using this inline
so I would drop the macros entirely. Also drop the mask definitions
as not adding anything for these single bit values.

Jonathan

> /* Measurement modes */
> #define CCS811_MODE_IDLE 0x00
> #define CCS811_MODE_IAQ_1SEC 0x10
> @@ -129,8 +134,10 @@ static int ccs811_start_sensor_application(struct i2c_client *client)
> if (ret < 0)
> return ret;
>
> - if ((ret & CCS811_STATUS_APP_VALID_MASK) !=
> - CCS811_STATUS_APP_VALID_LOADED)
> + if (IS_FW_MODE_APPLICATION(ret))
> + return 0;
> +
> + if (!IS_APP_VALID_LOADED(ret))
> return -EIO;
>
> ret = i2c_smbus_write_byte(client, CCS811_APP_START);
> @@ -141,8 +148,7 @@ static int ccs811_start_sensor_application(struct i2c_client *client)
> if (ret < 0)
> return ret;
>
> - if ((ret & CCS811_STATUS_FW_MODE_MASK) !=
> - CCS811_STATUS_FW_MODE_APPLICATION) {
> + if (!IS_FW_MODE_APPLICATION(ret)) {
> dev_err(&client->dev, "Application failed to start. Sensor is still in boot mode.\n");
> return -EIO;
> }