Re: [PATCH 2/5] media: dt-bindings: Add bindings for TDA1997X

[Tim Harvey]

On Thu, Nov 23, 2017 at 12:25 AM, Sakari Ailus <sakari.ailus@xxxxxx> wrote:
> On Wed, Nov 22, 2017 at 08:37:04PM -0800, Tim Harvey wrote:
>> On Tue, Nov 21, 2017 at 11:36 PM, Sakari Ailus <sakari.ailus@xxxxxx> wrote:
>> > Hi Tim,
>> >
>> > On Thu, Nov 09, 2017 at 10:45:33AM -0800, Tim Harvey wrote:
>> >> Cc: Rob Herring <robh@xxxxxxxxxx>
>> >> Signed-off-by: Tim Harvey <tharvey@xxxxxxxxxxxxx>
>> >> ---
>> >> v3:
>> >>  - fix typo
>> >>
>> >> v2:
>> >>  - add vendor prefix and remove _ from vidout-portcfg
>> >>  - remove _ from labels
>> >>  - remove max-pixel-rate property
>> >>  - describe and provide example for single output port
>> >>  - update to new audio port bindings
>> >> ---
>> >>  .../devicetree/bindings/media/i2c/tda1997x.txt     | 179 +++++++++++++++++++++
>> >>  1 file changed, 179 insertions(+)
>> >>  create mode 100644 Documentation/devicetree/bindings/media/i2c/tda1997x.txt
>> >>
>> >> diff --git a/Documentation/devicetree/bindings/media/i2c/tda1997x.txt b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
>> >> new file mode 100644
>> >> index 0000000..dd37f14
>> >> --- /dev/null
>> >> +++ b/Documentation/devicetree/bindings/media/i2c/tda1997x.txt
>> >> @@ -0,0 +1,179 @@
>> >> +Device-Tree bindings for the NXP TDA1997x HDMI receiver
>> >> +
>> >> +The TDA19971/73 are HDMI video receivers.
>> >> +
>> >> +The TDA19971 Video port output pins can be used as follows:
>> >> + - RGB 8bit per color (24 bits total): R[11:4] B[11:4] G[11:4]
>> >> + - YUV444 8bit per color (24 bits total): Y[11:4] Cr[11:4] Cb[11:4]
>> >> + - YUV422 semi-planar 8bit per component (16 bits total): Y[11:4] CbCr[11:4]
>> >> + - YUV422 semi-planar 10bit per component (20 bits total): Y[11:2] CbCr[11:2]
>> >> + - YUV422 semi-planar 12bit per component (24 bits total): - Y[11:0] CbCr[11:0]
>> >> + - YUV422 BT656 8bit per component (8 bits total): YCbCr[11:4] (2-cycles)
>> >> + - YUV422 BT656 10bit per component (10 bits total): YCbCr[11:2] (2-cycles)
>> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
>> >> +
>> >> +The TDA19973 Video port output pins can be used as follows:
>> >> + - RGB 12bit per color (36 bits total): R[11:0] B[11:0] G[11:0]
>> >> + - YUV444 12bit per color (36 bits total): Y[11:0] Cb[11:0] Cr[11:0]
>> >> + - YUV422 semi-planar 12bit per component (24 bits total): Y[11:0] CbCr[11:0]
>> >> + - YUV422 BT656 12bit per component (12 bits total): YCbCr[11:0] (2-cycles)
>> >> +
>> >> +The Video port output pins are mapped via 4-bit 'pin groups' allowing
>> >> +for a variety of connection possibilities including swapping pin order within
>> >> +pin groups. The video_portcfg device-tree property consists of register mapping
>> >> +pairs which map a chip-specific VP output register to a 4-bit pin group. If
>> >> +the pin group needs to be bit-swapped you can use the *_S pin-group defines.
>> >> +
>> >> +Required Properties:
>> >> + - compatible          :
>> >> +  - "nxp,tda19971" for the TDA19971
>> >> +  - "nxp,tda19973" for the TDA19973
>> >> + - reg                 : I2C slave address
>> >> + - interrupts          : The interrupt number
>> >> + - DOVDD-supply        : Digital I/O supply
>> >> + - DVDD-supply         : Digital Core supply
>> >> + - AVDD-supply         : Analog supply
>> >> + - nxp,vidout-portcfg  : array of pairs mapping VP output pins to pin groups.
>> >> +
>> >> +Optional Properties:
>> >> + - nxp,audout-format   : DAI bus format: "i2s" or "spdif".
>> >> + - nxp,audout-width    : width of audio output data bus (1-4).
>> >> + - nxp,audout-layout   : data layout (0=AP0 used, 1=AP0/AP1/AP2/AP3 used).
>> >> + - nxp,audout-mclk-fs  : Multiplication factor between stream rate and codec
>> >> +                         mclk.
>> >> +
>> >> +The device node must contain one 'port' child node for its digital output
>> >> +video port, in accordance with the video interface bindings defined in
>> >> +Documentation/devicetree/bindings/media/video-interfaces.txt.
>> >
>> > Could you add that this port has one endpoint node as well? (Unless you
>> > support multiple, that is.)
>>
>> Sure... will clarify as:
>>
>> The device node must contain one endpoint 'port' child node for its
>> digital output
>> video port, in accordance with the video interface bindings defined in
>> Documentation/devicetree/bindings/media/video-interfaces.txt.
>
> I think it'd be clearer if you just add "The port node shall contain one
> endpoint child node".

ok

>
>>
>> >> +
>> >> +Optional Endpoint Properties:
>> >> +  The following three properties are defined in video-interfaces.txt and
>> >> +  are valid for source endpoints only:
>> >
>> > Transmitters? Don't you have an endpoint only in the port representing the
>> > transmitter?
>>
>> I'm not usre what you mean.
>>
>> The TDA1997x is an HDMI receiver meaning it receives HDMI and decodes
>> it to a parallel video bus. HDMI transmitters are the opposite.
>
> The parallel bus. If you mean that, then you could just say that. "Source
> endpoint" is a bit vague, or requires knowing V4L2.
>

agreed

Thanks,

Tim