Re: [PATCH net-next 10/10] net: hns3: Add mqprio support when interacting with network stack

From: Yunsheng Lin
Date: Sun Sep 24 2017 - 20:45:59 EST


Hi, Jiri

On 2017/9/24 19:37, Jiri Pirko wrote:
> Sat, Sep 23, 2017 at 02:47:20AM CEST, linyunsheng@xxxxxxxxxx wrote:
>> Hi, Jiri
>>
>> On 2017/9/23 0:03, Jiri Pirko wrote:
>>> Fri, Sep 22, 2017 at 04:11:51PM CEST, linyunsheng@xxxxxxxxxx wrote:
>>>> Hi, Jiri
>>>>
>>>>>> - if (!tc) {
>>>>>> + if (if_running) {
>>>>>> + (void)hns3_nic_net_stop(netdev);
>>>>>> + msleep(100);
>>>>>> + }
>>>>>> +
>>>>>> + ret = (kinfo->dcb_ops && kinfo->dcb_ops->>setup_tc) ?
>>>>>> + kinfo->dcb_ops->setup_tc(h, tc, prio_tc) : ->EOPNOTSUPP;
>>>>
>>>>> This is most odd. Why do you call dcb_ops from >ndo_setup_tc callback?
>>>>> Why are you mixing this together? prio->tc mapping >can be done
>>>>> directly in dcbnl
>>>>
>>>> Here is what we do in dcb_ops->setup_tc:
>>>> Firstly, if current tc num is different from the tc num
>>>> that user provide, then we setup the queues for each
>>>> tc.
>>>>
>>>> Secondly, we tell hardware the pri to tc mapping that
>>>> the stack is using. In rx direction, our hardware need
>>>> that mapping to put different packet into different tc'
>>>> queues according to the priority of the packet, then
>>>> rss decides which specific queue in the tc should the
>>>> packet goto.
>>>>
>>>> By mixing, I suppose you meant why we need the
>>>> pri to tc infomation?
>>>
>>> by mixing, I mean what I wrote. You are calling dcb_ops callback from
>>> ndo_setup_tc callback. So you are mixing DCBNL subsystem and TC
>>> subsystem. Why? Why do you need sch_mqprio? Why DCBNL is not enough for
>>> all?
>>
>> When using lldptool, dcbnl is involved.
>>
>> But when using tc qdisc, dcbbl is not involved, below is the a few key
>> call graph in the kernel when tc qdisc cmd is executed.
>>
>> cmd:
>> tc qdisc add dev eth0 root handle 1:0 mqprio num_tc 4 map 1 2 3 3 1 3 1 1 hw 1
>>
>> call graph:
>> rtnetlink_rcv_msg -> tc_modify_qdisc -> qdisc_create -> mqprio_init ->
>> hns3_nic_setup_tc
>>
>> When hns3_nic_setup_tc is called, we need to know how many tc num and
>> prio_tc mapping from the tc_mqprio_qopt which is provided in the paramter
>> in the ndo_setup_tc function, and dcb_ops is the our hardware specific
>> method to setup the tc related parameter to the hardware, so this is why
>> we call dcb_ops callback in ndo_setup_tc callback.
>>
>> I hope this will answer your question, thanks for your time.
>
> Okay. I understand that you have a usecase for mqprio mapping offload
> without lldptool being involved. Ok. I believe it is wrong to call dcb_ops
> from tc callback. You should have a generic layer inside the driver and
> call it from both dcb_ops and tc callbacks.

Actually, dcb_ops is our generic layer inside the driver.
Below is high level architecture:

[ tc qdisc ] [ lldpad ]
| |
| |
| |
[ hns3_enet ] [ hns3_dcbnl ]
\ /
\ /
\ /
[ hclge_dcb ]
/ \
/ \
/ \
[ hclgc_main ] [ hclge_tm ]

hns3_enet.c implements the ndo_setup_tc callback.
hns3_dcbnl.c implements the dcbnl_rtnl_ops for stack's DCBNL system.
hclge_dcb implements the dcb_ops.
So we already have a generic layer that tc and dcbnl all call from.

>
> Also, what happens If I run lldptool concurrently with mqprio? Who wins
> and is going to configure the mapping?

Both lldptool and tc qdisc cmd use rtnl interface provided by stack, so
they are both protected by rtnl_lock, so we do not have to do the locking
in the driver.

The locking is in rtnetlink_rcv_msg:

rtnl_lock();
handlers = rtnl_dereference(rtnl_msg_handlers[family]);
if (handlers) {
doit = READ_ONCE(handlers[type].doit);
if (doit)
err = doit(skb, nlh, extack);
}
rtnl_unlock();

Thanks.

>
>
>>
>>>
>>>
>>>
>>>> I hope I did not misunderstand your question, thanks
>>>> for your time reviewing.
>>>
>>> .
>>>
>>
>
> .
>