[PATCH net-next v4 07/13] net: mvpp2: do not set GMAC autoneg when using XLG MAC

From: Antoine Tenart
Date: Wed Aug 30 2017 - 04:33:04 EST


When using the XLG MAC, it does not make sense to force the GMAC autoneg
parameters. This patch adds checks to only set the GMAC autoneg
parameters when needed (i.e. when not using the XLG MAC).

Signed-off-by: Antoine Tenart <antoine.tenart@xxxxxxxxxxxxxxxxxx>
---
drivers/net/ethernet/marvell/mvpp2.c | 64 +++++++++++++++++++++++-------------
1 file changed, 42 insertions(+), 22 deletions(-)

diff --git a/drivers/net/ethernet/marvell/mvpp2.c b/drivers/net/ethernet/marvell/mvpp2.c
index 09cad32734f3..2f05a0b0773c 100644
--- a/drivers/net/ethernet/marvell/mvpp2.c
+++ b/drivers/net/ethernet/marvell/mvpp2.c
@@ -5735,6 +5735,37 @@ static irqreturn_t mvpp2_isr(int irq, void *dev_id)
return IRQ_HANDLED;
}

+static void mvpp2_gmac_set_autoneg(struct mvpp2_port *port,
+ struct phy_device *phydev)
+{
+ u32 val;
+
+ if (port->phy_interface != PHY_INTERFACE_MODE_RGMII &&
+ port->phy_interface != PHY_INTERFACE_MODE_RGMII_ID &&
+ port->phy_interface != PHY_INTERFACE_MODE_RGMII_RXID &&
+ port->phy_interface != PHY_INTERFACE_MODE_RGMII_TXID &&
+ port->phy_interface != PHY_INTERFACE_MODE_SGMII)
+ return;
+
+ val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
+ MVPP2_GMAC_CONFIG_GMII_SPEED |
+ MVPP2_GMAC_CONFIG_FULL_DUPLEX |
+ MVPP2_GMAC_AN_SPEED_EN |
+ MVPP2_GMAC_AN_DUPLEX_EN);
+
+ if (phydev->duplex)
+ val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
+
+ if (phydev->speed == SPEED_1000)
+ val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
+ else if (phydev->speed == SPEED_100)
+ val |= MVPP2_GMAC_CONFIG_MII_SPEED;
+
+ writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+
+}
+
/* Adjust link */
static void mvpp2_link_event(struct net_device *dev)
{
@@ -5745,24 +5776,7 @@ static void mvpp2_link_event(struct net_device *dev)
if (phydev->link) {
if ((port->speed != phydev->speed) ||
(port->duplex != phydev->duplex)) {
- u32 val;
-
- val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
- val &= ~(MVPP2_GMAC_CONFIG_MII_SPEED |
- MVPP2_GMAC_CONFIG_GMII_SPEED |
- MVPP2_GMAC_CONFIG_FULL_DUPLEX |
- MVPP2_GMAC_AN_SPEED_EN |
- MVPP2_GMAC_AN_DUPLEX_EN);
-
- if (phydev->duplex)
- val |= MVPP2_GMAC_CONFIG_FULL_DUPLEX;
-
- if (phydev->speed == SPEED_1000)
- val |= MVPP2_GMAC_CONFIG_GMII_SPEED;
- else if (phydev->speed == SPEED_100)
- val |= MVPP2_GMAC_CONFIG_MII_SPEED;
-
- writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ mvpp2_gmac_set_autoneg(port, phydev);

port->duplex = phydev->duplex;
port->speed = phydev->speed;
@@ -5773,10 +5787,16 @@ static void mvpp2_link_event(struct net_device *dev)
port->link = phydev->link;

if (phydev->link) {
- val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
- val |= (MVPP2_GMAC_FORCE_LINK_PASS |
- MVPP2_GMAC_FORCE_LINK_DOWN);
- writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ if (port->phy_interface == PHY_INTERFACE_MODE_RGMII ||
+ port->phy_interface == PHY_INTERFACE_MODE_RGMII_ID ||
+ port->phy_interface == PHY_INTERFACE_MODE_RGMII_RXID ||
+ port->phy_interface == PHY_INTERFACE_MODE_RGMII_TXID ||
+ port->phy_interface == PHY_INTERFACE_MODE_SGMII) {
+ val = readl(port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ val |= (MVPP2_GMAC_FORCE_LINK_PASS |
+ MVPP2_GMAC_FORCE_LINK_DOWN);
+ writel(val, port->base + MVPP2_GMAC_AUTONEG_CONFIG);
+ }

mvpp2_interrupts_enable(port);
mvpp2_port_enable(port);
--
2.13.5