Re: [PATCH 1/1] cpufreq: imx6q: imx6ull: use PLL1 for frequency higher than 528MHz

From: Rafael J. Wysocki
Date: Tue Aug 01 2017 - 19:33:28 EST


On Friday, July 28, 2017 10:36:33 AM Sébastien Szymanski wrote:
> Setting the frequency higher than 528Mhz actually sets the ARM
> clock to 528MHz. That's because PLL2 is used as the root clock when the
> frequency is higher than 396MHz.
>
> cpupower frequency-set -f 792000
>
> arm_clk_root on the CCM_CLKO2 signal is 528MHz instead of 792MHz.
>
> [ 61.606383] cpu cpu0: 396 MHz, 1025 mV --> 792 MHz, 1225 mV
>
> pll2 1 1 528000000 0 0
> pll2_bypass 1 1 528000000 0 0
> pll2_bus 3 3 528000000 0 0
> ca7_secondary_sel 1 1 528000000 0 0
> step 1 1 528000000 0 0
> pll1_sw 1 1 528000000 0 0
> arm 1 1 528000000 0 0
>
> Fixes this by using the PLL1 as the root clock when the frequency is
> higher than 528MHz.
>
> cpupower frequency-set -f 792000
>
> arm_clk_root on the CCM_CLKO2 signal is now 792MHz as expected.
>
> [ 69.717987] cpu cpu0: 198 MHz, 950 mV --> 792 MHz, 1225 mV
>
> pll1 1 1 792000000 0 0
> pll1_bypass 1 1 792000000 0 0
> pll1_sys 1 1 792000000 0 0
> pll1_sw 1 1 792000000 0 0
> arm 1 1 792000000 0 0
>
> Signed-off-by: Sébastien Szymanski <sebastien.szymanski@xxxxxxxxxxxx>
> ---
> drivers/cpufreq/imx6q-cpufreq.c | 11 +++++++++--
> 1 file changed, 9 insertions(+), 2 deletions(-)
>
> diff --git a/drivers/cpufreq/imx6q-cpufreq.c b/drivers/cpufreq/imx6q-cpufreq.c
> index b6edd3c..e5fba50 100644
> --- a/drivers/cpufreq/imx6q-cpufreq.c
> +++ b/drivers/cpufreq/imx6q-cpufreq.c
> @@ -18,6 +18,7 @@
>
> #define PU_SOC_VOLTAGE_NORMAL 1250000
> #define PU_SOC_VOLTAGE_HIGH 1275000
> +#define FREQ_528_MHZ 528000000
> #define FREQ_1P2_GHZ 1200000000
>
> static struct regulator *arm_reg;
> @@ -110,14 +111,20 @@ static int imx6q_set_target(struct cpufreq_policy *policy, unsigned int index)
> * voltage of 528MHz, so lower the CPU frequency to one
> * half before changing CPU frequency.
> */
> - clk_set_rate(arm_clk, (old_freq >> 1) * 1000);
> - clk_set_parent(pll1_sw_clk, pll1_sys_clk);
> + if ((old_freq * 1000) <= FREQ_528_MHZ) {
> + clk_set_rate(arm_clk, (old_freq >> 1) * 1000);
> + clk_set_parent(pll1_sw_clk, pll1_sys_clk);
> + }
> if (freq_hz > clk_get_rate(pll2_pfd2_396m_clk))
> clk_set_parent(secondary_sel_clk, pll2_bus_clk);
> else
> clk_set_parent(secondary_sel_clk, pll2_pfd2_396m_clk);
> clk_set_parent(step_clk, secondary_sel_clk);
> clk_set_parent(pll1_sw_clk, step_clk);
> + if (freq_hz > FREQ_528_MHZ) {
> + clk_set_rate(pll1_sys_clk, freq_hz);
> + clk_set_parent(pll1_sw_clk, pll1_sys_clk);
> + }
> } else {
> clk_set_parent(step_clk, pll2_pfd2_396m_clk);
> clk_set_parent(pll1_sw_clk, step_clk);
>

Any comments anyone? Good, bad, ugly?