[PATCH V2 1/2] pinctrl: qcom: spmi-gpio: Add support for GPIO LV/MV subtype

From: fenglinw
Date: Wed Jul 19 2017 - 02:33:42 EST


From: Fenglin Wu <fenglinw@xxxxxxxxxxxxxx>

GPIO LV (low voltage)/MV (medium voltage) subtypes have different
features and register mappings than 4CH/8CH subtypes. Add support
for LV and MV subtypes.

Signed-off-by: Fenglin Wu <fenglinw@xxxxxxxxxxxxxx>
---
.../devicetree/bindings/pinctrl/qcom,pmic-gpio.txt | 17 +-
drivers/pinctrl/qcom/pinctrl-spmi-gpio.c | 281 +++++++++++++++++----
include/dt-bindings/pinctrl/qcom,pmic-gpio.h | 2 +
3 files changed, 250 insertions(+), 50 deletions(-)

diff --git a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
index 8d893a8..d9d2054 100644
--- a/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
+++ b/Documentation/devicetree/bindings/pinctrl/qcom,pmic-gpio.txt
@@ -98,7 +98,10 @@ to specify in a pin configuration subnode:
"dtest1",
"dtest2",
"dtest3",
- "dtest4"
+ "dtest4",
+ And following values are supported by LV/MV GPIO subtypes:
+ "func3",
+ "func4"

- bias-disable:
Usage: optional
@@ -183,6 +186,18 @@ to specify in a pin configuration subnode:
Value type: <none>
Definition: The specified pins are configured in open-source mode.

+- qcom,analog-pass:
+ Usage: optional
+ Value type: <none>
+ Definition: The specified pins are configured in analog-pass-through mode.
+
+- qcom,atest:
+ Usage: optional
+ Value type: <u32>
+ Definition: Selects ATEST rail to route to GPIO when it's configured
+ in analog-pass-through mode.
+ Valid values are 1-4 corresponding to ATEST1 to ATEST4.
+
Example:

pm8921_gpio: gpio@150 {
diff --git a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
index 664b641..6b21832 100644
--- a/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
+++ b/drivers/pinctrl/qcom/pinctrl-spmi-gpio.c
@@ -40,6 +40,8 @@
#define PMIC_GPIO_SUBTYPE_GPIOC_4CH 0x5
#define PMIC_GPIO_SUBTYPE_GPIO_8CH 0x9
#define PMIC_GPIO_SUBTYPE_GPIOC_8CH 0xd
+#define PMIC_GPIO_SUBTYPE_GPIO_LV 0x10
+#define PMIC_GPIO_SUBTYPE_GPIO_MV 0x11

#define PMIC_MPP_REG_RT_STS 0x10
#define PMIC_MPP_REG_RT_STS_VAL_MASK 0x1
@@ -48,8 +50,10 @@
#define PMIC_GPIO_REG_MODE_CTL 0x40
#define PMIC_GPIO_REG_DIG_VIN_CTL 0x41
#define PMIC_GPIO_REG_DIG_PULL_CTL 0x42
+#define PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL 0x44
#define PMIC_GPIO_REG_DIG_OUT_CTL 0x45
#define PMIC_GPIO_REG_EN_CTL 0x46
+#define PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL 0x4A

/* PMIC_GPIO_REG_MODE_CTL */
#define PMIC_GPIO_REG_MODE_VALUE_SHIFT 0x1
@@ -58,6 +62,12 @@
#define PMIC_GPIO_REG_MODE_DIR_SHIFT 4
#define PMIC_GPIO_REG_MODE_DIR_MASK 0x7

+#define PMIC_GPIO_MODE_DIGITAL_INPUT 0
+#define PMIC_GPIO_MODE_DIGITAL_OUTPUT 1
+#define PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT 2
+#define PMIC_GPIO_MODE_ANALOG_PASS_THRU 3
+#define PMIC_GPIO_REG_LV_MV_MODE_DIR_MASK 0x3
+
/* PMIC_GPIO_REG_DIG_VIN_CTL */
#define PMIC_GPIO_REG_VIN_SHIFT 0
#define PMIC_GPIO_REG_VIN_MASK 0x7
@@ -69,6 +79,11 @@
#define PMIC_GPIO_PULL_DOWN 4
#define PMIC_GPIO_PULL_DISABLE 5

+/* PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL for LV/MV */
+#define PMIC_GPIO_LV_MV_OUTPUT_INVERT 0x80
+#define PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT 7
+#define PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK 0xF
+
/* PMIC_GPIO_REG_DIG_OUT_CTL */
#define PMIC_GPIO_REG_OUT_STRENGTH_SHIFT 0
#define PMIC_GPIO_REG_OUT_STRENGTH_MASK 0x3
@@ -88,9 +103,28 @@

#define PMIC_GPIO_PHYSICAL_OFFSET 1

+/* PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL */
+#define PMIC_GPIO_LV_MV_ANA_MUX_SEL_MASK 0x3
+
/* Qualcomm specific pin configurations */
#define PMIC_GPIO_CONF_PULL_UP (PIN_CONFIG_END + 1)
#define PMIC_GPIO_CONF_STRENGTH (PIN_CONFIG_END + 2)
+#define PMIC_GPIO_CONF_ATEST (PIN_CONFIG_END + 3)
+#define PMIC_GPIO_CONF_ANALOG_PASS (PIN_CONFIG_END + 4)
+
+/* The index of each function in pmic_gpio_functions[] array */
+enum pmic_gpio_func_index {
+ PMIC_GPIO_FUNC_INDEX_NORMAL,
+ PMIC_GPIO_FUNC_INDEX_PAIRED,
+ PMIC_GPIO_FUNC_INDEX_FUNC1,
+ PMIC_GPIO_FUNC_INDEX_FUNC2,
+ PMIC_GPIO_FUNC_INDEX_FUNC3,
+ PMIC_GPIO_FUNC_INDEX_FUNC4,
+ PMIC_GPIO_FUNC_INDEX_DTEST1,
+ PMIC_GPIO_FUNC_INDEX_DTEST2,
+ PMIC_GPIO_FUNC_INDEX_DTEST3,
+ PMIC_GPIO_FUNC_INDEX_DTEST4,
+};

/**
* struct pmic_gpio_pad - keep current GPIO settings
@@ -102,12 +136,15 @@
* open-drain or open-source mode.
* @output_enabled: Set to true if GPIO output logic is enabled.
* @input_enabled: Set to true if GPIO input buffer logic is enabled.
+ * @analog_pass: Set to true if GPIO is in analog-pass-through mode.
+ * @lv_mv_type: Set to true if GPIO subtype is GPIO_LV(0x10) or GPIO_MV(0x11).
* @num_sources: Number of power-sources supported by this GPIO.
* @power_source: Current power-source used.
* @buffer_type: Push-pull, open-drain or open-source.
* @pullup: Constant current which flow trough GPIO output buffer.
* @strength: No, Low, Medium, High
* @function: See pmic_gpio_functions[]
+ * @atest: the ATEST selection for GPIO analog-pass-through mode
*/
struct pmic_gpio_pad {
u16 base;
@@ -117,12 +154,15 @@ struct pmic_gpio_pad {
bool have_buffer;
bool output_enabled;
bool input_enabled;
+ bool analog_pass;
+ bool lv_mv_type;
unsigned int num_sources;
unsigned int power_source;
unsigned int buffer_type;
unsigned int pullup;
unsigned int strength;
unsigned int function;
+ unsigned int atest;
};

struct pmic_gpio_state {
@@ -135,12 +175,16 @@ struct pmic_gpio_state {
static const struct pinconf_generic_params pmic_gpio_bindings[] = {
{"qcom,pull-up-strength", PMIC_GPIO_CONF_PULL_UP, 0},
{"qcom,drive-strength", PMIC_GPIO_CONF_STRENGTH, 0},
+ {"qcom,atest", PMIC_GPIO_CONF_ATEST, 0},
+ {"qcom,analog-pass", PMIC_GPIO_CONF_ANALOG_PASS, 0},
};

#ifdef CONFIG_DEBUG_FS
static const struct pin_config_item pmic_conf_items[ARRAY_SIZE(pmic_gpio_bindings)] = {
PCONFDUMP(PMIC_GPIO_CONF_PULL_UP, "pull up strength", NULL, true),
PCONFDUMP(PMIC_GPIO_CONF_STRENGTH, "drive-strength", NULL, true),
+ PCONFDUMP(PMIC_GPIO_CONF_ATEST, "atest", NULL, true),
+ PCONFDUMP(PMIC_GPIO_CONF_ANALOG_PASS, "analog-pass", NULL, true),
};
#endif

@@ -153,10 +197,16 @@ struct pmic_gpio_state {
};

static const char *const pmic_gpio_functions[] = {
- PMIC_GPIO_FUNC_NORMAL, PMIC_GPIO_FUNC_PAIRED,
- PMIC_GPIO_FUNC_FUNC1, PMIC_GPIO_FUNC_FUNC2,
- PMIC_GPIO_FUNC_DTEST1, PMIC_GPIO_FUNC_DTEST2,
- PMIC_GPIO_FUNC_DTEST3, PMIC_GPIO_FUNC_DTEST4,
+ [PMIC_GPIO_FUNC_INDEX_NORMAL] = PMIC_GPIO_FUNC_NORMAL,
+ [PMIC_GPIO_FUNC_INDEX_PAIRED] = PMIC_GPIO_FUNC_PAIRED,
+ [PMIC_GPIO_FUNC_INDEX_FUNC1] = PMIC_GPIO_FUNC_FUNC1,
+ [PMIC_GPIO_FUNC_INDEX_FUNC2] = PMIC_GPIO_FUNC_FUNC2,
+ [PMIC_GPIO_FUNC_INDEX_FUNC3] = PMIC_GPIO_FUNC_FUNC3,
+ [PMIC_GPIO_FUNC_INDEX_FUNC4] = PMIC_GPIO_FUNC_FUNC4,
+ [PMIC_GPIO_FUNC_INDEX_DTEST1] = PMIC_GPIO_FUNC_DTEST1,
+ [PMIC_GPIO_FUNC_INDEX_DTEST2] = PMIC_GPIO_FUNC_DTEST2,
+ [PMIC_GPIO_FUNC_INDEX_DTEST3] = PMIC_GPIO_FUNC_DTEST3,
+ [PMIC_GPIO_FUNC_INDEX_DTEST4] = PMIC_GPIO_FUNC_DTEST4,
};

static int pmic_gpio_read(struct pmic_gpio_state *state,
@@ -244,25 +294,67 @@ static int pmic_gpio_set_mux(struct pinctrl_dev *pctldev, unsigned function,
unsigned int val;
int ret;

+ if (function > PMIC_GPIO_FUNC_INDEX_DTEST4) {
+ pr_err("function: %d is not defined\n", function);
+ return -EINVAL;
+ }
+
pad = pctldev->desc->pins[pin].drv_data;
+ /*
+ * Non-LV/MV subtypes only support 2 special functions,
+ * offsetting the dtestx function values by 2
+ */
+ if (!pad->lv_mv_type) {
+ if (function == PMIC_GPIO_FUNC_INDEX_FUNC3 ||
+ function == PMIC_GPIO_FUNC_INDEX_FUNC4) {
+ pr_err("LV/MV subtype doesn't have func3/func4\n");
+ return -EINVAL;
+ }
+ if (function >= PMIC_GPIO_FUNC_INDEX_DTEST1)
+ function -= (PMIC_GPIO_FUNC_INDEX_DTEST1 -
+ PMIC_GPIO_FUNC_INDEX_FUNC3);
+ }

pad->function = function;

- val = 0;
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 2;
- else
- val = 1;
- }
+ if (pad->analog_pass)
+ val = PMIC_GPIO_MODE_ANALOG_PASS_THRU;
+ else if (pad->output_enabled && pad->input_enabled)
+ val = PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT;
+ else if (pad->output_enabled)
+ val = PMIC_GPIO_MODE_DIGITAL_OUTPUT;
+ else
+ val = PMIC_GPIO_MODE_DIGITAL_INPUT;

- val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
- val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
- val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+ if (pad->lv_mv_type) {
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;

- ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
- if (ret < 0)
- return ret;
+ val = pad->atest - 1;
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->out_value
+ << PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT;
+ val |= pad->function
+ & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK;
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL, val);
+ if (ret < 0)
+ return ret;
+ } else {
+ val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
+ val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;
+ }

val = pad->is_enabled << PMIC_GPIO_REG_MASTER_EN_SHIFT;

@@ -322,6 +414,12 @@ static int pmic_gpio_config_get(struct pinctrl_dev *pctldev,
case PMIC_GPIO_CONF_STRENGTH:
arg = pad->strength;
break;
+ case PMIC_GPIO_CONF_ATEST:
+ arg = pad->atest;
+ break;
+ case PMIC_GPIO_CONF_ANALOG_PASS:
+ arg = pad->analog_pass;
+ break;
default:
return -EINVAL;
}
@@ -396,6 +494,16 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
return -EINVAL;
pad->strength = arg;
break;
+ case PMIC_GPIO_CONF_ATEST:
+ if (!pad->lv_mv_type || arg > 4)
+ return -EINVAL;
+ pad->atest = arg;
+ break;
+ case PMIC_GPIO_CONF_ANALOG_PASS:
+ if (!pad->lv_mv_type)
+ return -EINVAL;
+ pad->analog_pass = true;
+ break;
default:
return -EINVAL;
}
@@ -420,19 +528,46 @@ static int pmic_gpio_config_set(struct pinctrl_dev *pctldev, unsigned int pin,
if (ret < 0)
return ret;

- val = 0;
- if (pad->output_enabled) {
- if (pad->input_enabled)
- val = 2;
- else
- val = 1;
- }
+ if (pad->analog_pass)
+ val = PMIC_GPIO_MODE_ANALOG_PASS_THRU;
+ else if (pad->output_enabled && pad->input_enabled)
+ val = PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT;
+ else if (pad->output_enabled)
+ val = PMIC_GPIO_MODE_DIGITAL_OUTPUT;
+ else
+ val = PMIC_GPIO_MODE_DIGITAL_INPUT;

- val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
- val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
- val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+ if (pad->lv_mv_type) {
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->atest - 1;
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL, val);
+ if (ret < 0)
+ return ret;
+
+ val = pad->out_value
+ << PMIC_GPIO_LV_MV_OUTPUT_INVERT_SHIFT;
+ val |= pad->function
+ & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK;
+ ret = pmic_gpio_write(state, pad,
+ PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL, val);
+ if (ret < 0)
+ return ret;
+ } else {
+ val = val << PMIC_GPIO_REG_MODE_DIR_SHIFT;
+ val |= pad->function << PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ val |= pad->out_value & PMIC_GPIO_REG_MODE_VALUE_SHIFT;

- return pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+ ret = pmic_gpio_write(state, pad, PMIC_GPIO_REG_MODE_CTL, val);
+ if (ret < 0)
+ return ret;
+ }
+
+ return ret;
}

static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
@@ -440,7 +575,7 @@ static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
{
struct pmic_gpio_state *state = pinctrl_dev_get_drvdata(pctldev);
struct pmic_gpio_pad *pad;
- int ret, val;
+ int ret, val, function;

static const char *const biases[] = {
"pull-up 30uA", "pull-up 1.5uA", "pull-up 31.5uA",
@@ -462,7 +597,6 @@ static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
if (val < 0 || !(val >> PMIC_GPIO_REG_MASTER_EN_SHIFT)) {
seq_puts(s, " ---");
} else {
-
if (pad->input_enabled) {
ret = pmic_gpio_read(state, pad, PMIC_MPP_REG_RT_STS);
if (ret < 0)
@@ -471,14 +605,28 @@ static void pmic_gpio_config_dbg_show(struct pinctrl_dev *pctldev,
ret &= PMIC_MPP_REG_RT_STS_VAL_MASK;
pad->out_value = ret;
}
-
- seq_printf(s, " %-4s", pad->output_enabled ? "out" : "in");
- seq_printf(s, " %-7s", pmic_gpio_functions[pad->function]);
+ /*
+ * For the non-LV/MV subtypes only 2 special functions are
+ * available, offsetting the dtest function values by 2.
+ */
+ function = pad->function;
+ if (!pad->lv_mv_type &&
+ pad->function >= PMIC_GPIO_FUNC_INDEX_FUNC3)
+ function += PMIC_GPIO_FUNC_INDEX_DTEST1 -
+ PMIC_GPIO_FUNC_INDEX_FUNC3;
+
+ if (pad->analog_pass)
+ seq_puts(s, " analog-pass");
+ else
+ seq_printf(s, " %-4s",
+ pad->output_enabled ? "out" : "in");
+ seq_printf(s, " %-7s", pmic_gpio_functions[function]);
seq_printf(s, " vin-%d", pad->power_source);
seq_printf(s, " %-27s", biases[pad->pullup]);
seq_printf(s, " %-10s", buffer_types[pad->buffer_type]);
seq_printf(s, " %-4s", pad->out_value ? "high" : "low");
seq_printf(s, " %-7s", strengths[pad->strength]);
+ seq_printf(s, " atest-%d", pad->atest);
}
}

@@ -618,40 +766,71 @@ static int pmic_gpio_populate(struct pmic_gpio_state *state,
case PMIC_GPIO_SUBTYPE_GPIOC_8CH:
pad->num_sources = 8;
break;
+ case PMIC_GPIO_SUBTYPE_GPIO_LV:
+ pad->num_sources = 1;
+ pad->have_buffer = true;
+ pad->lv_mv_type = true;
+ break;
+ case PMIC_GPIO_SUBTYPE_GPIO_MV:
+ pad->num_sources = 2;
+ pad->have_buffer = true;
+ pad->lv_mv_type = true;
+ break;
default:
dev_err(state->dev, "unknown GPIO type 0x%x\n", subtype);
return -ENODEV;
}

- val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL);
- if (val < 0)
- return val;
+ if (pad->lv_mv_type) {
+ val = pmic_gpio_read(state, pad,
+ PMIC_GPIO_REG_LV_MV_DIG_OUT_SOURCE_CTL);
+ if (val < 0)
+ return val;
+
+ pad->out_value = !!(val & PMIC_GPIO_LV_MV_OUTPUT_INVERT);
+ pad->function = val & PMIC_GPIO_LV_MV_OUTPUT_SOURCE_SEL_MASK;
+
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL);
+ if (val < 0)
+ return val;
+
+ dir = val & PMIC_GPIO_REG_LV_MV_MODE_DIR_MASK;
+ } else {
+ val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_MODE_CTL);
+ if (val < 0)
+ return val;

- pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+ pad->out_value = val & PMIC_GPIO_REG_MODE_VALUE_SHIFT;
+
+ dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT;
+ dir &= PMIC_GPIO_REG_MODE_DIR_MASK;
+ pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
+ pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK;
+ }

- dir = val >> PMIC_GPIO_REG_MODE_DIR_SHIFT;
- dir &= PMIC_GPIO_REG_MODE_DIR_MASK;
switch (dir) {
- case 0:
+ case PMIC_GPIO_MODE_DIGITAL_INPUT:
pad->input_enabled = true;
pad->output_enabled = false;
break;
- case 1:
+ case PMIC_GPIO_MODE_DIGITAL_OUTPUT:
pad->input_enabled = false;
pad->output_enabled = true;
break;
- case 2:
+ case PMIC_GPIO_MODE_DIGITAL_INPUT_OUTPUT:
pad->input_enabled = true;
pad->output_enabled = true;
break;
+ case PMIC_GPIO_MODE_ANALOG_PASS_THRU:
+ if (!pad->lv_mv_type)
+ return -ENODEV;
+ pad->analog_pass = true;
+ break;
default:
dev_err(state->dev, "unknown GPIO direction\n");
return -ENODEV;
}

- pad->function = val >> PMIC_GPIO_REG_MODE_FUNCTION_SHIFT;
- pad->function &= PMIC_GPIO_REG_MODE_FUNCTION_MASK;
-
val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_VIN_CTL);
if (val < 0)
return val;
@@ -666,16 +845,20 @@ static int pmic_gpio_populate(struct pmic_gpio_state *state,
pad->pullup = val >> PMIC_GPIO_REG_PULL_SHIFT;
pad->pullup &= PMIC_GPIO_REG_PULL_MASK;

- val = pmic_gpio_read(state, pad, PMIC_GPIO_REG_DIG_OUT_CTL);
- if (val < 0)
- return val;
-
pad->strength = val >> PMIC_GPIO_REG_OUT_STRENGTH_SHIFT;
pad->strength &= PMIC_GPIO_REG_OUT_STRENGTH_MASK;

pad->buffer_type = val >> PMIC_GPIO_REG_OUT_TYPE_SHIFT;
pad->buffer_type &= PMIC_GPIO_REG_OUT_TYPE_MASK;

+ if (pad->lv_mv_type) {
+ val = pmic_gpio_read(state, pad,
+ PMIC_GPIO_REG_LV_MV_ANA_PASS_THRU_SEL);
+ if (val < 0)
+ return val;
+ pad->atest = (val & PMIC_GPIO_LV_MV_ANA_MUX_SEL_MASK) + 1;
+ }
+
/* Pin could be disabled with PIN_CONFIG_BIAS_HIGH_IMPEDANCE */
pad->is_enabled = true;
return 0;
diff --git a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
index d33f17c..b8ff882 100644
--- a/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
+++ b/include/dt-bindings/pinctrl/qcom,pmic-gpio.h
@@ -98,6 +98,8 @@
#define PMIC_GPIO_FUNC_PAIRED "paired"
#define PMIC_GPIO_FUNC_FUNC1 "func1"
#define PMIC_GPIO_FUNC_FUNC2 "func2"
+#define PMIC_GPIO_FUNC_FUNC3 "func3"
+#define PMIC_GPIO_FUNC_FUNC4 "func4"
#define PMIC_GPIO_FUNC_DTEST1 "dtest1"
#define PMIC_GPIO_FUNC_DTEST2 "dtest2"
#define PMIC_GPIO_FUNC_DTEST3 "dtest3"
--
Qualcomm Innovation Center, Inc. is a member of the Code Aurora Forum,
a Linux Foundation Collaborative Project.