[PATCH 5/5] ARM: dts: sama5d27_som1_ek: Add sama5d27 SoM1 EK support

From: Claudiu Beznea
Date: Thu Jun 29 2017 - 07:45:42 EST


Add specifig DTS files and bindings for sama5d27 SoM1 EK board.

Signed-off-by: Claudiu Beznea <claudiu.beznea@xxxxxxxxxxxxx>
Signed-off-by: Cristian Birsan <cristian.birsan@xxxxxxxxxxxxx>
---
arch/arm/boot/dts/Makefile | 1 +
arch/arm/boot/dts/at91-sama5d27_som1_ek.dts | 551 ++++++++++++++++++++++++++++
2 files changed, 552 insertions(+)
create mode 100644 arch/arm/boot/dts/at91-sama5d27_som1_ek.dts

diff --git a/arch/arm/boot/dts/Makefile b/arch/arm/boot/dts/Makefile
index 9449493..3396f73 100644
--- a/arch/arm/boot/dts/Makefile
+++ b/arch/arm/boot/dts/Makefile
@@ -46,6 +46,7 @@ dtb-$(CONFIG_SOC_AT91SAM9) += \
at91sam9x35ek.dtb
dtb-$(CONFIG_SOC_SAM_V7) += \
at91-kizbox2.dtb \
+ at91-sama5d27_som1_ek.dtb \
at91-sama5d2_xplained.dtb \
at91-sama5d3_xplained.dtb \
at91-tse850-3.dtb \
diff --git a/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
new file mode 100644
index 0000000..a87125e
--- /dev/null
+++ b/arch/arm/boot/dts/at91-sama5d27_som1_ek.dts
@@ -0,0 +1,551 @@
+/*
+ * at91-sama5d27_som1_ek.dts - Device Tree file for SAMA5D27-SOM1-EK board
+ *
+ * Copyright (c) 2017, Microchip Technology Inc.
+ * 2016 Nicolas Ferre <nicolas.ferre@xxxxxxxxx>
+ * 2017 Cristian Birsan <cristian.birsan@xxxxxxxxxxxxx>
+ * 2017 Claudiu Beznea <claudiu.beznea@xxxxxxxxxxxxx>
+ *
+ * This file is dual-licensed: you can use it either under the terms
+ * of the GPL or the X11 license, at your option. Note that this dual
+ * licensing only applies to this file, and not this project as a
+ * whole.
+ *
+ * a) This file is free software; you can redistribute it and/or
+ * modify it under the terms of the GNU General Public License as
+ * published by the Free Software Foundation; either version 2 of the
+ * License, or (at your option) any later version.
+ *
+ * This file is distributed in the hope that it will be useful,
+ * but WITHOUT ANY WARRANTY; without even the implied warranty of
+ * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the
+ * GNU General Public License for more details.
+ *
+ * Or, alternatively,
+ *
+ * b) Permission is hereby granted, free of charge, to any person
+ * obtaining a copy of this software and associated documentation
+ * files (the "Software"), to deal in the Software without
+ * restriction, including without limitation the rights to use,
+ * copy, modify, merge, publish, distribute, sublicense, and/or
+ * sell copies of the Software, and to permit persons to whom the
+ * Software is furnished to do so, subject to the following
+ * conditions:
+ *
+ * The above copyright notice and this permission notice shall be
+ * included in all copies or substantial portions of the Software.
+ *
+ * THE SOFTWARE IS PROVIDED "AS IS", WITHOUT WARRANTY OF ANY KIND,
+ * EXPRESS OR IMPLIED, INCLUDING BUT NOT LIMITED TO THE WARRANTIES
+ * OF MERCHANTABILITY, FITNESS FOR A PARTICULAR PURPOSE AND
+ * NONINFRINGEMENT. IN NO EVENT SHALL THE AUTHORS OR COPYRIGHT
+ * HOLDERS BE LIABLE FOR ANY CLAIM, DAMAGES OR OTHER LIABILITY,
+ * WHETHER IN AN ACTION OF CONTRACT, TORT OR OTHERWISE, ARISING
+ * FROM, OUT OF OR IN CONNECTION WITH THE SOFTWARE OR THE USE OR
+ * OTHER DEALINGS IN THE SOFTWARE.
+ */
+/dts-v1/;
+#include "at91-sama5d27_som1.dtsi"
+#include <dt-bindings/mfd/atmel-flexcom.h>
+#include <dt-bindings/gpio/gpio.h>
+
+/ {
+ model = "Atmel SAMA5D27 SOM1 EK";
+ compatible = "atmel,sama5d27-som1-ek", "atmel,sama5d27-som1", "atmel,sama5d27", "atmel,sama5d2", "atmel,sama5";
+
+ chosen {
+ stdout-path = "serial0:115200n8";
+ };
+
+ memory {
+ reg = <0x20000000 0x20000>;
+ };
+
+ ahb {
+ usb0: gadget@00300000 {
+ atmel,vbus-gpio = <&pioA 116 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usba_vbus>;
+ status = "okay";
+ };
+
+ usb1: ohci@00400000 {
+ num-ports = <3>;
+ atmel,vbus-gpio = <&pioA 10 GPIO_ACTIVE_HIGH>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_usb_default>;
+ status = "okay";
+ };
+
+ usb2: ehci@00500000 {
+ status = "okay";
+ };
+
+ sdmmc0: sdio-host@a0000000 {
+ bus-width = <8>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc0_default>;
+ status = "okay";
+ };
+
+ sdmmc1: sdio-host@b0000000 {
+ bus-width = <4>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_sdmmc1_default>;
+ status = "okay";
+ };
+
+ apb {
+ isc: isc@f0008000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_isc_base &pinctrl_isc_data_8bit &pinctrl_isc_data_9_10 &pinctrl_isc_data_11_12>;
+ status = "okay";
+ };
+
+ spi0: spi@f8000000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_spi0_default>;
+ status = "okay";
+ };
+
+ macb0: ethernet@f8008000 {
+ status = "okay";
+ };
+
+ uart1: serial@f8020000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart1_default>;
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ status = "okay";
+ };
+
+ uart2: serial@f8024000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mikrobus2_uart>;
+ atmel,use-dma-rx;
+ atmel-use-dma-tx;
+ status = "okay";
+ };
+
+ pwm0: pwm@f802c000 {
+ status = "okay";
+ };
+
+ flx1: flexcom@f8038000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_TWI>;
+ status = "disabled";
+
+ i2c2: i2c@600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <20 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx1_clk>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mikrobus_i2c>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ shdwc@f8048010 {
+ atmel,shdwc-debouncer = <976>;
+ atmel,wakeup-rtc-timer;
+
+ input@0 {
+ reg = <0>;
+ atmel,wakeup-type = "low";
+ };
+ };
+
+ watchdog@f8048040 {
+ status = "okay";
+ };
+
+ can0: can@f8054000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can0_default>;
+ };
+
+ uart3: serial@fc008000 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_uart3_default>;
+ status = "disabled";
+ };
+
+ uart4: serial@fc00c000 {
+ atmel,use-dma-rx;
+ atmel,use-dma-tx;
+ pinctrl-name = "default";
+ pinctrl-0 = <&pinctrl_mikrobus1_uart>;
+ status = "okay";
+ };
+
+ flx3: flexcom@fc014000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+ status = "disabled";
+
+ uart7: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&flx3_clk>;
+ clock-names = "usart";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx3_default>;
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
+ spi2: spi@400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <22 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&flx3_clk>;
+ clock-names = "spi_clk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx3_default>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ flx4: flexcom@fc018000 {
+ atmel,flexcom-mode = <ATMEL_FLEXCOM_MODE_SPI>;
+ status = "okay";
+
+ uart6: serial@200 {
+ compatible = "atmel,at91sam9260-usart";
+ reg = <0x200 0x200>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&flx4_clk>;
+ clock-names = "usart";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx4_default>;
+ atmel,fifo-size = <32>;
+ status = "disabled";
+ };
+
+ spi3: spi@400 {
+ compatible = "atmel,at91rm9200-spi";
+ reg = <0x400 0x200>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+ clocks = <&flx4_clk>;
+ clock-names = "spi_clk";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_mikrobus_spi &pinctrl_mikrobus1_spi_cs &pinctrl_mikrobus2_spi_cs>;
+ atmel,fifo-size = <16>;
+ status = "okay";
+ };
+
+ i2c3: i2c@600 {
+ compatible = "atmel,sama5d2-i2c";
+ reg = <0x600 0x200>;
+ interrupts = <23 IRQ_TYPE_LEVEL_HIGH 7>;
+ dmas = <0>, <0>;
+ dma-names = "tx", "rx";
+ #address-cells = <1>;
+ #size-cells = <0>;
+ clocks = <&flx4_clk>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_flx4_default>;
+ atmel,fifo-size = <16>;
+ status = "disabled";
+ };
+ };
+
+ i2c1: i2c@fc028000 {
+ dmas = <0>, <0>;
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_i2c1_default>;
+ status = "okay";
+ };
+
+ pinctrl@fc038000 {
+
+ pinctrl_can0_default: can0_default {
+ pinmux = <PIN_PC10__CANTX0>,
+ <PIN_PC11__CANRX0>;
+ bias-disable;
+ };
+
+ pinctrl_can1_default: can1_default {
+ pinmux = <PIN_PC26__CANTX1>,
+ <PIN_PC27__CANRX1>;
+ bias-disable;
+ };
+
+ pinctrl_flx3_default: flx3_default {
+ pinmux = <PIN_PC20__FLEXCOM3_IO0>,
+ <PIN_PC19__FLEXCOM3_IO1>,
+ <PIN_PC18__FLEXCOM3_IO2>,
+ <PIN_PC21__FLEXCOM3_IO3>,
+ <PIN_PC22__FLEXCOM3_IO4>;
+ bias-disable;
+ };
+
+ pinctrl_i2c1_default: i2c1_default {
+ pinmux = <PIN_PD4__TWD1>,
+ <PIN_PD5__TWCK1>;
+ bias-disable;
+ };
+
+ pinctrl_isc_base: isc_base {
+ pinmux = <PIN_PC21__ISC_PCK>,
+ <PIN_PC22__ISC_VSYNC>,
+ <PIN_PC23__ISC_HSYNC>,
+ <PIN_PC24__ISC_MCK>;
+ bias-disable;
+ };
+
+ pinctrl_isc_data_8bit: isc_data_8bit {
+ pinmux = <PIN_PC20__ISC_D11>,
+ <PIN_PC19__ISC_D10>,
+ <PIN_PC18__ISC_D9>,
+ <PIN_PC17__ISC_D8>,
+ <PIN_PC16__ISC_D7>,
+ <PIN_PC15__ISC_D6>,
+ <PIN_PC14__ISC_D5>,
+ <PIN_PC13__ISC_D4>;
+ bias-disable;
+ };
+
+ pinctrl_isc_data_9_10: isc_data_9_10 {
+ pinmux = <PIN_PC12__ISC_D3>,
+ <PIN_PC11__ISC_D2>;
+ bias-disable;
+ };
+
+ pinctrl_isc_data_11_12: isc_data_11_12 {
+ pinmux = <PIN_PC10__ISC_D1>,
+ <PIN_PC9__ISC_D0>;
+ bias-disable;
+ };
+
+ pinctrl_key_gpio_default: key_gpio_default {
+ pinmux = <PIN_PA29__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_led_gpio_default: led_gpio_default {
+ pinmux = <PIN_PA27__GPIO>,
+ <PIN_PB1__GPIO>,
+ <PIN_PA31__GPIO>;
+ bias-pull-up;
+ };
+
+ pinctrl_sdmmc0_default: sdmmc0_default {
+ cmd_data {
+ pinmux = <PIN_PA1__SDMMC0_CMD>,
+ <PIN_PA2__SDMMC0_DAT0>,
+ <PIN_PA3__SDMMC0_DAT1>,
+ <PIN_PA4__SDMMC0_DAT2>,
+ <PIN_PA5__SDMMC0_DAT3>,
+ <PIN_PA6__SDMMC0_DAT4>,
+ <PIN_PA7__SDMMC0_DAT5>,
+ <PIN_PA8__SDMMC0_DAT6>,
+ <PIN_PA9__SDMMC0_DAT7>;
+ bias-pull-up;
+ };
+
+ ck_cd_vddsel {
+ pinmux = <PIN_PA0__SDMMC0_CK>,
+ <PIN_PA11__SDMMC0_VDDSEL>,
+ <PIN_PA13__SDMMC0_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sdmmc1_default: sdmmc1_default {
+ cmd_data {
+ pinmux = <PIN_PA28__SDMMC1_CMD>,
+ <PIN_PA18__SDMMC1_DAT0>,
+ <PIN_PA19__SDMMC1_DAT1>,
+ <PIN_PA20__SDMMC1_DAT2>,
+ <PIN_PA21__SDMMC1_DAT3>;
+ bias-pull-up;
+ };
+
+ conf-ck_cd {
+ pinmux = <PIN_PA22__SDMMC1_CK>,
+ <PIN_PA30__SDMMC1_CD>;
+ bias-disable;
+ };
+ };
+
+ pinctrl_sensor_power: sensor_power {
+ pinmux = <PIN_PB12__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_sensor_reset: sensor_reset {
+ pinmux = <PIN_PB11__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_spi0_default: spi0_default {
+ pinmux = <PIN_PA14__SPI0_SPCK>,
+ <PIN_PA15__SPI0_MOSI>,
+ <PIN_PA16__SPI0_MISO>,
+ <PIN_PA17__SPI0_NPCS0>;
+ bias-disable;
+ };
+
+ pinctrl_uart1_default: uart1_default {
+ pinmux = <PIN_PD2__URXD1>,
+ <PIN_PD3__UTXD1>;
+ bias-disable;
+ };
+
+ pinctrl_uart3_default: uart3_default {
+ pinmux = <PIN_PC12__URXD3>,
+ <PIN_PC13__UTXD3>;
+ bias-disable;
+ };
+
+ pinctrl_usb_default: usb_default {
+ pinmux = <PIN_PA10__GPIO>,
+ <PIN_PD19__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_usba_vbus: usba_vbus {
+ pinmux = <PIN_PD20__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_an: mikrobus1_an {
+ pinmux = <PIN_PD25__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_an: mikrobus2_an {
+ pinmux = <PIN_PD26__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_rst: mikrobus1_rst {
+ pinmux = <PIN_PB2__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_rst: mikrobus2_rst {
+ pinmux = <PIN_PA26__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_spi_cs: mikrobus1_spi_cs {
+ pinmux = <PIN_PD0__FLEXCOM4_IO4>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_spi_cs: mikrobus2_spi_cs {
+ pinmux = <PIN_PC31__FLEXCOM4_IO3>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus_spi: mikrobus_spi {
+ pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+ <PIN_PC29__FLEXCOM4_IO1>,
+ <PIN_PC30__FLEXCOM4_IO2>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_pwm: mikrobus1_pwm {
+ pinmux = <PIN_PB1__PWML1>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_pwm: mikrobus2_pwm {
+ pinmux = <PIN_PA31__PWML0>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_int: mikrobus1_int {
+ pinmux = <PIN_PB0__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_int: mikrobus2_int {
+ pinmux = <PIN_PA25__GPIO>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus1_uart: mikrobus1_uart {
+ pinmux = <PIN_PB3__URXD4>,
+ <PIN_PB4__UTXD4>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus2_uart: mikrobus2_uart {
+ pinmux = <PIN_PD23__URXD2>,
+ <PIN_PD24__UTXD2>;
+ bias-disable;
+ };
+
+ pinctrl_mikrobus_i2c: mikrobus1_i2c {
+ pinmux = <PIN_PA24__FLEXCOM1_IO0>,
+ <PIN_PA23__FLEXCOM1_IO1>;
+ bias-disable;
+ };
+
+ pinctrl_flx4_default: flx4_uart_default {
+ pinmux = <PIN_PC28__FLEXCOM4_IO0>,
+ <PIN_PC29__FLEXCOM4_IO1>,
+ <PIN_PC30__FLEXCOM4_IO2>,
+ <PIN_PC31__FLEXCOM4_IO3>,
+ <PIN_PD0__FLEXCOM4_IO4>;
+ bias-disable;
+ };
+ };
+
+ can1: can@fc050000 {
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_can1_default>;
+ status = "okay";
+ };
+ };
+ };
+
+ gpio_keys {
+ compatible = "gpio-keys";
+
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_key_gpio_default>;
+
+ bp1 {
+ label = "USER";
+ gpios = <&pioA 29 GPIO_ACTIVE_LOW>;
+ linux,code = <0x104>;
+ };
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-names = "default";
+ pinctrl-0 = <&pinctrl_led_gpio_default>;
+ status = "okay";
+
+ red {
+ label = "red";
+ gpios = <&pioA 27 GPIO_ACTIVE_LOW>;
+ };
+
+ green {
+ label = "green";
+ gpios = <&pioA 33 GPIO_ACTIVE_LOW>;
+ };
+
+ blue {
+ label = "blue";
+ gpios = <&pioA 31 GPIO_ACTIVE_LOW>;
+ linux,default-trigger = "heartbeat";
+ };
+ };
+};
--
2.7.4