[PATCH v2 1/3] drivers: crypto: Add Support for Octeon-tx CPT Engine

From: George Cherian
Date: Tue Dec 13 2016 - 10:37:36 EST


Enable the Physical Function diver for the Cavium Crypto Engine (CPT)
found in Octeon-tx series of SoC's. CPT is the Cryptographic Acceleration
Unit. CPT includes microcoded GigaCypher symmetric engines (SEs) and
asymmetric engines (AEs).

Signed-off-by: George Cherian <george.cherian@xxxxxxxxxx>
---
drivers/crypto/cavium/cpt/Kconfig | 16 +
drivers/crypto/cavium/cpt/Makefile | 2 +
drivers/crypto/cavium/cpt/cpt_common.h | 166 +++++++
drivers/crypto/cavium/cpt/cpt_hw_types.h | 736 +++++++++++++++++++++++++++++++
drivers/crypto/cavium/cpt/cptpf.h | 69 +++
drivers/crypto/cavium/cpt/cptpf_main.c | 733 ++++++++++++++++++++++++++++++
drivers/crypto/cavium/cpt/cptpf_mbox.c | 163 +++++++
7 files changed, 1885 insertions(+)
create mode 100644 drivers/crypto/cavium/cpt/Kconfig
create mode 100644 drivers/crypto/cavium/cpt/Makefile
create mode 100644 drivers/crypto/cavium/cpt/cpt_common.h
create mode 100644 drivers/crypto/cavium/cpt/cpt_hw_types.h
create mode 100644 drivers/crypto/cavium/cpt/cptpf.h
create mode 100644 drivers/crypto/cavium/cpt/cptpf_main.c
create mode 100644 drivers/crypto/cavium/cpt/cptpf_mbox.c

diff --git a/drivers/crypto/cavium/cpt/Kconfig b/drivers/crypto/cavium/cpt/Kconfig
new file mode 100644
index 0000000..247f1cb
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/Kconfig
@@ -0,0 +1,16 @@
+#
+# Cavium crypto device configuration
+#
+
+config CRYPTO_DEV_CPT
+ tristate
+
+config CAVIUM_CPT
+ tristate "Cavium Cryptographic Accelerator driver"
+ depends on ARCH_THUNDER
+ select CRYPTO_DEV_CPT
+ help
+ Support for Cavium CPT block found in octeon-tx series of
+ processors.
+
+ To compile this as a module, choose M here.
diff --git a/drivers/crypto/cavium/cpt/Makefile b/drivers/crypto/cavium/cpt/Makefile
new file mode 100644
index 0000000..fe3d454
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/Makefile
@@ -0,0 +1,2 @@
+obj-$(CONFIG_CAVIUM_CPT) += cptpf.o
+cptpf-objs := cptpf_main.o cptpf_mbox.o
diff --git a/drivers/crypto/cavium/cpt/cpt_common.h b/drivers/crypto/cavium/cpt/cpt_common.h
new file mode 100644
index 0000000..ae542f4
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/cpt_common.h
@@ -0,0 +1,166 @@
+/*
+ * Copyright (C) 2016 Cavium, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#ifndef __CPT_COMMON_H
+#define __CPT_COMMON_H
+
+#include <asm/byteorder.h>
+#include <linux/delay.h>
+#include <linux/pci.h>
+
+#include "cpt_hw_types.h"
+
+/* Device ID */
+#define CPT_81XX_PCI_PF_DEVICE_ID 0xa040
+#define CPT_81XX_PCI_VF_DEVICE_ID 0xa041
+
+/**< flags to indicate the features supported */
+#define CPT_FLAG_MSIX_ENABLED BIT(0)
+#define CPT_FLAG_SRIOV_ENABLED BIT(1)
+#define CPT_FLAG_VF_DRIVER BIT(2)
+#define CPT_FLAG_DEVICE_READY BIT(3)
+
+#define cpt_msix_enabled(cpt) ((cpt)->flags & CPT_FLAG_MSIX_ENABLED)
+#define cpt_sriov_enabled(cpt) ((cpt)->flags & CPT_FLAG_SRIOV_ENABLED)
+#define cpt_vf_driver(cpt) ((cpt)->flags & CPT_FLAG_VF_DRIVER)
+#define cpt_device_ready(cpt) ((cpt)->flags & CPT_FLAG_DEVICE_READY)
+
+#define CPT_MBOX_MSG_TYPE_ACK 1
+#define CPT_MBOX_MSG_TYPE_NACK 2
+#define CPT_MBOX_MSG_TIMEOUT 2000
+#define VF_STATE_DOWN 0
+#define VF_STATE_UP 1
+
+/*
+ * CPT Registers map for 81xx
+ */
+
+/* PF registers */
+#define CPTX_PF_CONSTANTS(a) (0x0ll + ((u64)(a) << 36))
+#define CPTX_PF_RESET(a) (0x100ll + ((u64)(a) << 36))
+#define CPTX_PF_DIAG(a) (0x120ll + ((u64)(a) << 36))
+#define CPTX_PF_BIST_STATUS(a) (0x160ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_CTL(a) (0x200ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_FLIP(a) (0x210ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_INT(a) (0x220ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_INT_W1S(a) (0x230ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_ENA_W1S(a) (0x240ll + ((u64)(a) << 36))
+#define CPTX_PF_ECC0_ENA_W1C(a) (0x250ll + ((u64)(a) << 36))
+#define CPTX_PF_MBOX_INTX(a, b) \
+ (0x400ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_MBOX_INT_W1SX(a, b) \
+ (0x420ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_MBOX_ENA_W1CX(a, b) \
+ (0x440ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_MBOX_ENA_W1SX(a, b) \
+ (0x460ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_EXEC_INT(a) (0x500ll + 0x1000000000ll * ((a) & 0x1))
+#define CPTX_PF_EXEC_INT_W1S(a) (0x520ll + ((u64)(a) << 36))
+#define CPTX_PF_EXEC_ENA_W1C(a) (0x540ll + ((u64)(a) << 36))
+#define CPTX_PF_EXEC_ENA_W1S(a) (0x560ll + ((u64)(a) << 36))
+#define CPTX_PF_GX_EN(a, b) \
+ (0x600ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_EXEC_INFO(a) (0x700ll + ((u64)(a) << 36))
+#define CPTX_PF_EXEC_BUSY(a) (0x800ll + ((u64)(a) << 36))
+#define CPTX_PF_EXEC_INFO0(a) (0x900ll + ((u64)(a) << 36))
+#define CPTX_PF_EXEC_INFO1(a) (0x910ll + ((u64)(a) << 36))
+#define CPTX_PF_INST_REQ_PC(a) (0x10000ll + ((u64)(a) << 36))
+#define CPTX_PF_INST_LATENCY_PC(a) \
+ (0x10020ll + ((u64)(a) << 36))
+#define CPTX_PF_RD_REQ_PC(a) (0x10040ll + ((u64)(a) << 36))
+#define CPTX_PF_RD_LATENCY_PC(a) (0x10060ll + ((u64)(a) << 36))
+#define CPTX_PF_RD_UC_PC(a) (0x10080ll + ((u64)(a) << 36))
+#define CPTX_PF_ACTIVE_CYCLES_PC(a) (0x10100ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_CTL(a) (0x4000000ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_STATUS(a) (0x4000008ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_CLK(a) (0x4000010ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_DBG_CTL(a) (0x4000018ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_DBG_DATA(a) (0x4000020ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_BIST_STATUS(a) (0x4000028ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_REQ_TIMER(a) (0x4000030ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_MEM_CTL(a) (0x4000038ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_PERF_CTL(a) (0x4001000ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_DBG_CNTX(a, b) \
+ (0x4001100ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_EXE_PERF_EVENT_CNT(a) (0x4001180ll + ((u64)(a) << 36))
+#define CPTX_PF_EXE_EPCI_INBX_CNT(a, b) \
+ (0x4001200ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_EXE_EPCI_OUTBX_CNT(a, b) \
+ (0x4001240ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_ENGX_UCODE_BASE(a, b) \
+ (0x4002000ll + ((u64)(a) << 36) + ((b) << 3))
+#define CPTX_PF_QX_CTL(a, b) \
+ (0x8000000ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_PF_QX_GMCTL(a, b) \
+ (0x8000020ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_PF_QX_CTL2(a, b) \
+ (0x8000100ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_PF_VFX_MBOXX(a, b, c) \
+ (0x8001000ll + ((u64)(a) << 36) + ((b) << 20) + ((c) << 8))
+
+/* VF registers */
+#define CPTX_VQX_CTL(a, b) (0x100ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_SADDR(a, b) (0x200ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_WAIT(a, b) (0x400ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_INPROG(a, b) (0x410ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE(a, b) (0x420ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_ACK(a, b) (0x440ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_INT_W1S(a, b) (0x460ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_INT_W1C(a, b) (0x468ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_ENA_W1S(a, b) (0x470ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DONE_ENA_W1C(a, b) (0x478ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_MISC_INT(a, b) (0x500ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_MISC_INT_W1S(a, b) (0x508ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_MISC_ENA_W1S(a, b) (0x510ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_MISC_ENA_W1C(a, b) (0x518ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VQX_DOORBELL(a, b) (0x600ll + ((u64)(a) << 36) + ((b) << 20))
+#define CPTX_VFX_PF_MBOXX(a, b, c) \
+ (0x1000ll + ((u64)(a) << 36) + ((b) << 20) + ((c) << 3))
+
+enum vftype {
+ AE_TYPES = 1,
+ SE_TYPES = 2,
+ BAD_CPT_TYPES,
+};
+
+/* Max CPT devices supported */
+enum cpt_mbox_opcode {
+ CPT_MSG_VF_UP = 1,
+ CPT_MSG_VF_DOWN,
+ CPT_MSG_READY,
+ CPT_MSG_QLEN,
+ CPT_MSG_QBIND_GRP,
+ CPT_MSG_VQ_PRIORITY,
+};
+
+/* CPT mailbox structure */
+struct cpt_mbox {
+ u64 msg; /* Message type MBOX[0] */
+ u64 data;/* Data MBOX[1] */
+};
+
+/* The Cryptographic Acceleration Unit can *only* be found in SoCs
+ * containing the ThunderX ARM64 CPU implementation. All accesses to the device
+ * registers on this platform are implicitly strongly ordered with respect
+ * to memory accesses. So writeq_relaxed() and readq_relaxed() are safe to use
+ * with no memory barriers in this driver. The readq()/writeq() functions add
+ * explicit ordering operation which in this case are redundant, and only
+ * add overhead.
+ */
+/* Register read/write APIs */
+static inline void cpt_write_csr64(u8 __iomem *hw_addr, u64 offset,
+ u64 val)
+{
+ writeq_relaxed(val, hw_addr + offset);
+}
+
+static inline u64 cpt_read_csr64(u8 __iomem *hw_addr, u64 offset)
+{
+ return readq_relaxed(hw_addr + offset);
+}
+#endif /* __CPT_COMMON_H */
diff --git a/drivers/crypto/cavium/cpt/cpt_hw_types.h b/drivers/crypto/cavium/cpt/cpt_hw_types.h
new file mode 100644
index 0000000..3798803
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/cpt_hw_types.h
@@ -0,0 +1,736 @@
+/*
+ * Copyright (C) 2016 Cavium, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#ifndef __CPT_HW_TYPES_H
+#define __CPT_HW_TYPES_H
+
+#include "cpt_common.h"
+
+/**
+ * Enumeration cpt_comp_e
+ *
+ * CPT Completion Enumeration
+ * Enumerates the values of CPT_RES_S[COMPCODE].
+ */
+enum cpt_comp_e {
+ CPT_COMP_E_NOTDONE = 0x00,
+ CPT_COMP_E_GOOD = 0x01,
+ CPT_COMP_E_FAULT = 0x02,
+ CPT_COMP_E_SWERR = 0x03,
+ CPT_COMP_E_LAST_ENTRY = 0xFF
+};
+
+/**
+ * Structure cpt_inst_s
+ *
+ * CPT Instruction Structure
+ * This structure specifies the instruction layout. Instructions are
+ * stored in memory as little-endian unless CPT()_PF_Q()_CTL[INST_BE] is set.
+ * cpt_inst_s_s
+ * Word 0
+ * doneint:1 Done interrupt.
+ * 0 = No interrupts related to this instruction.
+ * 1 = When the instruction completes, CPT()_VQ()_DONE[DONE] will be
+ * incremented,and based on the rules described there an interrupt may
+ * occur.
+ * Word 1
+ * res_addr:64 [127: 64] Result IOVA.
+ * If nonzero, specifies where to write CPT_RES_S.
+ * If zero, no result structure will be written.
+ * Address must be 16-byte aligned.
+ * Bits <63:49> are ignored by hardware; software should use a
+ * sign-extended bit <48> for forward compatibility.
+ * Word 2
+ * grp:10 [171:162] If [WQ_PTR] is nonzero, the SSO guest-group to use when
+ * CPT submits work SSO.
+ * For the SSO to not discard the add-work request, FPA_PF_MAP() must map
+ * [GRP] and CPT()_PF_Q()_GMCTL[GMID] as valid.
+ * tt:2 [161:160] If [WQ_PTR] is nonzero, the SSO tag type to use when CPT
+ * submits work to SSO
+ * tag:32 [159:128] If [WQ_PTR] is nonzero, the SSO tag to use when CPT
+ * submits work to SSO.
+ * Word 3
+ * wq_ptr:64 [255:192] If [WQ_PTR] is nonzero, it is a pointer to a
+ * work-queue entry that CPT submits work to SSO after all context,
+ * output data, and result write operations are visible to other
+ * CNXXXX units and the cores. Bits <2:0> must be zero.
+ * Bits <63:49> are ignored by hardware; software should
+ * use a sign-extended bit <48> for forward compatibility.
+ * Internal:
+ * Bits <63:49>, <2:0> are ignored by hardware, treated as always 0x0.
+ * Word 4
+ * ei0:64; [319:256] Engine instruction word 0. Passed to the AE/SE.
+ * Word 5
+ * ei1:64; [383:320] Engine instruction word 1. Passed to the AE/SE.
+ * Word 6
+ * ei2:64; [447:384] Engine instruction word 1. Passed to the AE/SE.
+ * Word 7
+ * ei3:64; [511:448] Engine instruction word 1. Passed to the AE/SE.
+ *
+ */
+union cpt_inst_s {
+ u64 u[8];
+ struct cpt_inst_s_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_17_63:47;
+ u64 doneint:1;
+ u64 reserved_0_1:16;
+#else /* Word 0 - Little Endian */
+ u64 reserved_0_15:16;
+ u64 doneint:1;
+ u64 reserved_17_63:47;
+#endif /* Word 0 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 1 - Big Endian */
+ u64 res_addr:64;
+#else /* Word 1 - Little Endian */
+ u64 res_addr:64;
+#endif /* Word 1 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 2 - Big Endian */
+ u64 reserved_172_19:20;
+ u64 grp:10;
+ u64 tt:2;
+ u64 tag:32;
+#else /* Word 2 - Little Endian */
+ u64 tag:32;
+ u64 tt:2;
+ u64 grp:10;
+ u64 reserved_172_191:20;
+#endif /* Word 2 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 3 - Big Endian */
+ u64 wq_ptr:64;
+#else /* Word 3 - Little Endian */
+ u64 wq_ptr:64;
+#endif /* Word 3 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 4 - Big Endian */
+ u64 ei0:64;
+#else /* Word 4 - Little Endian */
+ u64 ei0:64;
+#endif /* Word 4 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 5 - Big Endian */
+ u64 ei1:64;
+#else /* Word 5 - Little Endian */
+ u64 ei1:64;
+#endif /* Word 5 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 6 - Big Endian */
+ u64 ei2:64;
+#else /* Word 6 - Little Endian */
+ u64 ei2:64;
+#endif /* Word 6 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 7 - Big Endian */
+ u64 ei3:64;
+#else /* Word 7 - Little Endian */
+ u64 ei3:64;
+#endif /* Word 7 - End */
+ } s;
+};
+
+/**
+ * Structure cpt_res_s
+ *
+ * CPT Result Structure
+ * The CPT coprocessor writes the result structure after it completes a
+ * CPT_INST_S instruction. The result structure is exactly 16 bytes, and
+ * each instruction completion produces exactly one result structure.
+ *
+ * This structure is stored in memory as little-endian unless
+ * CPT()_PF_Q()_CTL[INST_BE] is set.
+ * cpt_res_s_s
+ * Word 0
+ * doneint:1 [16:16] Done interrupt. This bit is copied from the
+ * corresponding instruction's CPT_INST_S[DONEINT].
+ * compcode:8 [7:0] Indicates completion/error status of the CPT coprocessor
+ * for the associated instruction, as enumerated by CPT_COMP_E.
+ * Core software may write the memory location containing [COMPCODE] to
+ * 0x0 before ringing the doorbell, and then poll for completion by
+ * checking for a nonzero value.
+ * Once the core observes a nonzero [COMPCODE] value in this case,the CPT
+ * coprocessor will have also completed L2/DRAM write operations.
+ * Word 1
+ * reserved
+ *
+ */
+union cpt_res_s {
+ u64 u[2];
+ struct cpt_res_s_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_17_63:47;
+ u64 doneint:1;
+ u64 reserved_8_15:8;
+ u64 compcode:8;
+#else /* Word 0 - Little Endian */
+ u64 compcode:8;
+ u64 reserved_8_15:8;
+ u64 doneint:1;
+ u64 reserved_17_63:47;
+#endif /* Word 0 - End */
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 1 - Big Endian */
+ u64 reserved_64_127:64;
+#else /* Word 1 - Little Endian */
+ u64 reserved_64_127:64;
+#endif /* Word 1 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_bist_status
+ *
+ * CPT PF Control Bist Status Register
+ * This register has the BIST status of memories. Each bit is the BIST result
+ * of an individual memory (per bit, 0 = pass and 1 = fail).
+ * cptx_pf_bist_status_s
+ * Word0
+ * bstatus [29:0](RO/H) BIST status. One bit per memory, enumerated by
+ * CPT_RAMS_E.
+ */
+union cptx_pf_bist_status {
+ u64 u;
+ struct cptx_pf_bist_status_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_30_63:34;
+ u64 bstatus:30;
+#else /* Word 0 - Little Endian */
+ u64 bstatus:30;
+ u64 reserved_30_63:34;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_constants
+ *
+ * CPT PF Constants Register
+ * This register contains implementation-related parameters of CPT in CNXXXX.
+ * cptx_pf_constants_s
+ * Word 0
+ * reserved_40_63:24 [63:40] Reserved.
+ * epcis:8 [39:32](RO) Number of EPCI busses.
+ * grps:8 [31:24](RO) Number of engine groups implemented.
+ * ae:8 [23:16](RO/H) Number of AEs. In CNXXXX, for CPT0 returns 0x0,
+ * for CPT1 returns 0x18, or less if there are fuse-disables.
+ * se:8 [15:8](RO/H) Number of SEs. In CNXXXX, for CPT0 returns 0x30,
+ * or less if there are fuse-disables, for CPT1 returns 0x0.
+ * vq:8 [7:0](RO) Number of VQs.
+ */
+union cptx_pf_constants {
+ u64 u;
+ struct cptx_pf_constants_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_40_63:24;
+ u64 epcis:8;
+ u64 grps:8;
+ u64 ae:8;
+ u64 se:8;
+ u64 vq:8;
+#else /* Word 0 - Little Endian */
+ u64 vq:8;
+ u64 se:8;
+ u64 ae:8;
+ u64 grps:8;
+ u64 epcis:8;
+ u64 reserved_40_63:24;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_exe_bist_status
+ *
+ * CPT PF Engine Bist Status Register
+ * This register has the BIST status of each engine. Each bit is the
+ * BIST result of an individual engine (per bit, 0 = pass and 1 = fail).
+ * cptx_pf_exe_bist_status_s
+ * Word0
+ * reserved_48_63:16 [63:48] reserved
+ * bstatus:48 [47:0](RO/H) BIST status. One bit per engine.
+ *
+ */
+union cptx_pf_exe_bist_status {
+ u64 u;
+ struct cptx_pf_exe_bist_status_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_48_63:16;
+ u64 bstatus:48;
+#else /* Word 0 - Little Endian */
+ u64 bstatus:48;
+ u64 reserved_48_63:16;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_exe_ctl
+ *
+ * CPT PF Engine Control Register
+ * This register enables the engines.
+ * cptx_pf_exe_ctl_s
+ * Word0
+ * enable:64 [63:0](R/W) Individual enables for each of the engines.
+ */
+union cptx_pf_exe_ctl {
+ u64 u;
+ struct cptx_pf_exe_ctl_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 enable:64;
+#else /* Word 0 - Little Endian */
+ u64 enable:64;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_q#_ctl
+ *
+ * CPT Queue Control Register
+ * This register configures queues. This register should be changed only
+ * when quiescent (see CPT()_VQ()_INPROG[INFLIGHT]).
+ * cptx_pf_qx_ctl_s
+ * Word0
+ * reserved_60_63:4 [63:60] reserved.
+ * aura:12; [59:48](R/W) Guest-aura for returning this queue's
+ * instruction-chunk buffers to FPA. Only used when [INST_FREE] is set.
+ * For the FPA to not discard the request, FPA_PF_MAP() must map
+ * [AURA] and CPT()_PF_Q()_GMCTL[GMID] as valid.
+ * reserved_45_47:3 [47:45] reserved.
+ * size:13 [44:32](R/W) Command-buffer size, in number of 64-bit words per
+ * command buffer segment. Must be 8*n + 1, where n is the number of
+ * instructions per buffer segment.
+ * reserved_11_31:21 [31:11] Reserved.
+ * cont_err:1 [10:10](R/W) Continue on error.
+ * 0 = When CPT()_VQ()_MISC_INT[NWRP], CPT()_VQ()_MISC_INT[IRDE] or
+ * CPT()_VQ()_MISC_INT[DOVF] are set by hardware or software via
+ * CPT()_VQ()_MISC_INT_W1S, then CPT()_VQ()_CTL[ENA] is cleared. Due to
+ * pipelining, additional instructions may have been processed between the
+ * instruction causing the error and the next instruction in the disabled
+ * queue (the instruction at CPT()_VQ()_SADDR).
+ * 1 = Ignore errors and continue processing instructions.
+ * For diagnostic use only.
+ * inst_free:1 [9:9](R/W) Instruction FPA free. When set, when CPT reaches the
+ * end of an instruction chunk, that chunk will be freed to the FPA.
+ * inst_be:1 [8:8](R/W) Instruction big-endian control. When set, instructions,
+ * instruction next chunk pointers, and result structures are stored in
+ * big-endian format in memory.
+ * iqb_ldwb:1 [7:7](R/W) Instruction load don't write back.
+ * 0 = The hardware issues NCB transient load (LDT) towards the cache,
+ * which if the line hits and is is dirty will cause the line to be
+ * written back before being replaced.
+ * 1 = The hardware issues NCB LDWB read-and-invalidate command towards
+ * the cache when fetching the last word of instructions; as a result the
+ * line will not be written back when replaced. This improves
+ * performance, but software must not read the instructions after they are
+ * posted to the hardware. Reads that do not consume the last word of a
+ * cache line always use LDI.
+ * reserved_4_6:3 [6:4] Reserved.
+ * grp:3; [3:1](R/W) Engine group.
+ * pri:1; [0:0](R/W) Queue priority.
+ * 1 = This queue has higher priority. Round-robin between higher
+ * priority queues.
+ * 0 = This queue has lower priority. Round-robin between lower
+ * priority queues.
+ */
+union cptx_pf_qx_ctl {
+ u64 u;
+ struct cptx_pf_qx_ctl_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_60_63:4;
+ u64 aura:12;
+ u64 reserved_45_47:3;
+ u64 size:13;
+ u64 reserved_11_31:21;
+ u64 cont_err:1;
+ u64 inst_free:1;
+ u64 inst_be:1;
+ u64 iqb_ldwb:1;
+ u64 reserved_4_6:3;
+ u64 grp:3;
+ u64 pri:1;
+#else /* Word 0 - Little Endian */
+ u64 pri:1;
+ u64 grp:3;
+ u64 reserved_4_6:3;
+ u64 iqb_ldwb:1;
+ u64 inst_be:1;
+ u64 inst_free:1;
+ u64 cont_err:1;
+ u64 reserved_11_31:21;
+ u64 size:13;
+ u64 reserved_45_47:3;
+ u64 aura:12;
+ u64 reserved_60_63:4;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_pf_g#_en
+ *
+ * CPT PF Group Control Register
+ * This register configures engine groups.
+ * cptx_pf_gx_en_s
+ * Word0
+ * en: 64; [63:0](R/W/H) Engine group enable. One bit corresponds to each
+ * engine, with the bit set to indicate this engine can service this group.
+ * Bits corresponding to unimplemented engines read as zero, i.e. only bit
+ * numbers less than CPT()_PF_CONSTANTS[AE] + CPT()_PF_CONSTANTS[SE] are
+ * writable. AE engine bits follow SE engine bits.
+ * E.g. if CPT()_PF_CONSTANTS[AE] = 0x1, and CPT()_PF_CONSTANTS[SE] = 0x2,
+ * then bits <2:0> are read/writable with bit <2> corresponding to AE<0>,
+ * and bit <1> to SE<1>, and bit<0> to SE<0>. Before disabling an engine,
+ * the corresponding bit in each group must be cleared. CPT()_PF_EXEC_BUSY
+ * can then be polled to determing when the engine becomes idle.
+ * At the point, the engine can be disabled.
+ */
+union cptx_pf_gx_en {
+ u64 u;
+ struct cptx_pf_gx_en_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 en:64;
+#else /* Word 0 - Little Endian */
+ u64 en:64;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_saddr
+ *
+ * CPT Queue Starting Buffer Address Registers
+ * These registers set the instruction buffer starting address.
+ * cptx_vqx_saddr_s
+ * Word0
+ * reserved_49_63:15 [63:49] Reserved.
+ * ptr:43 [48:6](R/W/H) Instruction buffer IOVA <48:6> (64-byte aligned).
+ * When written, it is the initial buffer starting address; when read,
+ * it is the next read pointer to be requested from L2C. The PTR field
+ * is overwritten with the next pointer each time that the command buffer
+ * segment is exhausted. New commands will then be read from the newly
+ * specified command buffer pointer.
+ * reserved_0_5:6 [5:0] Reserved.
+ *
+ */
+union cptx_vqx_saddr {
+ u64 u;
+ struct cptx_vqx_saddr_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_49_63:15;
+ u64 ptr:43;
+ u64 reserved_0_5:6;
+#else /* Word 0 - Little Endian */
+ u64 reserved_0_5:6;
+ u64 ptr:43;
+ u64 reserved_49_63:15;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_misc_ena_w1s
+ *
+ * CPT Queue Misc Interrupt Enable Set Register
+ * This register sets interrupt enable bits.
+ * cptx_vqx_misc_ena_w1s_s
+ * Word0
+ * reserved_5_63:59 [63:5] Reserved.
+ * swerr:1 [4:4](R/W1S/H) Reads or sets enable for
+ * CPT(0..1)_VQ(0..63)_MISC_INT[SWERR].
+ * nwrp:1 [3:3](R/W1S/H) Reads or sets enable for
+ * CPT(0..1)_VQ(0..63)_MISC_INT[NWRP].
+ * irde:1 [2:2](R/W1S/H) Reads or sets enable for
+ * CPT(0..1)_VQ(0..63)_MISC_INT[IRDE].
+ * dovf:1 [1:1](R/W1S/H) Reads or sets enable for
+ * CPT(0..1)_VQ(0..63)_MISC_INT[DOVF].
+ * mbox:1 [0:0](R/W1S/H) Reads or sets enable for
+ * CPT(0..1)_VQ(0..63)_MISC_INT[MBOX].
+ *
+ */
+union cptx_vqx_misc_ena_w1s {
+ u64 u;
+ struct cptx_vqx_misc_ena_w1s_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_5_63:59;
+ u64 swerr:1;
+ u64 nwrp:1;
+ u64 irde:1;
+ u64 dovf:1;
+ u64 mbox:1;
+#else /* Word 0 - Little Endian */
+ u64 mbox:1;
+ u64 dovf:1;
+ u64 irde:1;
+ u64 nwrp:1;
+ u64 swerr:1;
+ u64 reserved_5_63:59;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_doorbell
+ *
+ * CPT Queue Doorbell Registers
+ * Doorbells for the CPT instruction queues.
+ * cptx_vqx_doorbell_s
+ * Word0
+ * reserved_20_63:44 [63:20] Reserved.
+ * dbell_cnt:20 [19:0](R/W/H) Number of instruction queue 64-bit words to add
+ * to the CPT instruction doorbell count. Readback value is the the
+ * current number of pending doorbell requests. If counter overflows
+ * CPT()_VQ()_MISC_INT[DBELL_DOVF] is set. To reset the count back to
+ * zero, write one to clear CPT()_VQ()_MISC_INT_ENA_W1C[DBELL_DOVF],
+ * then write a value of 2^20 minus the read [DBELL_CNT], then write one
+ * to CPT()_VQ()_MISC_INT_W1C[DBELL_DOVF] and
+ * CPT()_VQ()_MISC_INT_ENA_W1S[DBELL_DOVF]. Must be a multiple of 8.
+ * All CPT instructions are 8 words and require a doorbell count of
+ * multiple of 8.
+ */
+union cptx_vqx_doorbell {
+ u64 u;
+ struct cptx_vqx_doorbell_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_20_63:44;
+ u64 dbell_cnt:20;
+#else /* Word 0 - Little Endian */
+ u64 dbell_cnt:20;
+ u64 reserved_20_63:44;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_inprog
+ *
+ * CPT Queue In Progress Count Registers
+ * These registers contain the per-queue instruction in flight registers.
+ * cptx_vqx_inprog_s
+ * Word0
+ * reserved_8_63:56 [63:8] Reserved.
+ * inflight:8 [7:0](RO/H) Inflight count. Counts the number of instructions
+ * for the VF for which CPT is fetching, executing or responding to
+ * instructions. However this does not include any interrupts that are
+ * awaiting software handling (CPT()_VQ()_DONE[DONE] != 0x0).
+ * A queue may not be reconfigured until:
+ * 1. CPT()_VQ()_CTL[ENA] is cleared by software.
+ * 2. [INFLIGHT] is polled until equals to zero.
+ */
+union cptx_vqx_inprog {
+ u64 u;
+ struct cptx_vqx_inprog_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_8_63:56;
+ u64 inflight:8;
+#else /* Word 0 - Little Endian */
+ u64 inflight:8;
+ u64 reserved_8_63:56;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_misc_int
+ *
+ * CPT Queue Misc Interrupt Register
+ * These registers contain the per-queue miscellaneous interrupts.
+ * cptx_vqx_misc_int_s
+ * Word 0
+ * reserved_5_63:59 [63:5] Reserved.
+ * swerr:1 [4:4](R/W1C/H) Software error from engines.
+ * nwrp:1 [3:3](R/W1C/H) NCB result write response error.
+ * irde:1 [2:2](R/W1C/H) Instruction NCB read response error.
+ * dovf:1 [1:1](R/W1C/H) Doorbell overflow.
+ * mbox:1 [0:0](R/W1C/H) PF to VF mailbox interrupt. Set when
+ * CPT()_VF()_PF_MBOX(0) is written.
+ *
+ */
+union cptx_vqx_misc_int {
+ u64 u;
+ struct cptx_vqx_misc_int_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_5_63:59;
+ u64 swerr:1;
+ u64 nwrp:1;
+ u64 irde:1;
+ u64 dovf:1;
+ u64 mbox:1;
+#else /* Word 0 - Little Endian */
+ u64 mbox:1;
+ u64 dovf:1;
+ u64 irde:1;
+ u64 nwrp:1;
+ u64 swerr:1;
+ u64 reserved_5_63:59;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_done_ack
+ *
+ * CPT Queue Done Count Ack Registers
+ * This register is written by software to acknowledge interrupts.
+ * cptx_vqx_done_ack_s
+ * Word0
+ * reserved_20_63:44 [63:20] Reserved.
+ * done_ack:20 [19:0](R/W/H) Number of decrements to CPT()_VQ()_DONE[DONE].
+ * Reads CPT()_VQ()_DONE[DONE]. Written by software to acknowledge
+ * interrupts. If CPT()_VQ()_DONE[DONE] is still nonzero the interrupt
+ * will be re-sent if the conditions described in CPT()_VQ()_DONE[DONE]
+ * are satisfied.
+ *
+ */
+union cptx_vqx_done_ack {
+ u64 u;
+ struct cptx_vqx_done_ack_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_20_63:44;
+ u64 done_ack:20;
+#else /* Word 0 - Little Endian */
+ u64 done_ack:20;
+ u64 reserved_20_63:44;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_done
+ *
+ * CPT Queue Done Count Registers
+ * These registers contain the per-queue instruction done count.
+ * cptx_vqx_done_s
+ * Word0
+ * reserved_20_63:44 [63:20] Reserved.
+ * done:20 [19:0](R/W/H) Done count. When CPT_INST_S[DONEINT] set and that
+ * instruction completes, CPT()_VQ()_DONE[DONE] is incremented when the
+ * instruction finishes. Write to this field are for diagnostic use only;
+ * instead software writes CPT()_VQ()_DONE_ACK with the number of
+ * decrements for this field.
+ * Interrupts are sent as follows:
+ * * When CPT()_VQ()_DONE[DONE] = 0, then no results are pending, the
+ * interrupt coalescing timer is held to zero, and an interrupt is not
+ * sent.
+ * * When CPT()_VQ()_DONE[DONE] != 0, then the interrupt coalescing timer
+ * counts. If the counter is >= CPT()_VQ()_DONE_WAIT[TIME_WAIT]*1024, or
+ * CPT()_VQ()_DONE[DONE] >= CPT()_VQ()_DONE_WAIT[NUM_WAIT], i.e. enough
+ * time has passed or enough results have arrived, then the interrupt is
+ * sent.
+ * * When CPT()_VQ()_DONE_ACK is written (or CPT()_VQ()_DONE is written
+ * but this is not typical), the interrupt coalescing timer restarts.
+ * Note after decrementing this interrupt equation is recomputed,
+ * for example if CPT()_VQ()_DONE[DONE] >= CPT()_VQ()_DONE_WAIT[NUM_WAIT]
+ * and because the timer is zero, the interrupt will be resent immediately.
+ * (This covers the race case between software acknowledging an interrupt
+ * and a result returning.)
+ * * When CPT()_VQ()_DONE_ENA_W1S[DONE] = 0, interrupts are not sent,
+ * but the counting described above still occurs.
+ * Since CPT instructions complete out-of-order, if software is using
+ * completion interrupts the suggested scheme is to request a DONEINT on
+ * each request, and when an interrupt arrives perform a "greedy" scan for
+ * completions; even if a later command is acknowledged first this will
+ * not result in missing a completion.
+ * Software is responsible for making sure [DONE] does not overflow;
+ * for example by insuring there are not more than 2^20-1 instructions in
+ * flight that may request interrupts.
+ *
+ */
+union cptx_vqx_done {
+ u64 u;
+ struct cptx_vqx_done_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_20_63:44;
+ u64 done:20;
+#else /* Word 0 - Little Endian */
+ u64 done:20;
+ u64 reserved_20_63:44;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_done_wait
+ *
+ * CPT Queue Done Interrupt Coalescing Wait Registers
+ * Specifies the per queue interrupt coalescing settings.
+ * cptx_vqx_done_wait_s
+ * Word0
+ * reserved_48_63:16 [63:48] Reserved.
+ * time_wait:16; [47:32](R/W) Time hold-off. When CPT()_VQ()_DONE[DONE] = 0
+ * or CPT()_VQ()_DONE_ACK is written a timer is cleared. When the timer
+ * reaches [TIME_WAIT]*1024 then interrupt coalescing ends.
+ * see CPT()_VQ()_DONE[DONE]. If 0x0, time coalescing is disabled.
+ * reserved_20_31:12 [31:20] Reserved.
+ * num_wait:20 [19:0](R/W) Number of messages hold-off.
+ * When CPT()_VQ()_DONE[DONE] >= [NUM_WAIT] then interrupt coalescing ends
+ * see CPT()_VQ()_DONE[DONE]. If 0x0, same behavior as 0x1.
+ *
+ */
+union cptx_vqx_done_wait {
+ u64 u;
+ struct cptx_vqx_done_wait_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_48_63:16;
+ u64 time_wait:16;
+ u64 reserved_20_31:12;
+ u64 num_wait:20;
+#else /* Word 0 - Little Endian */
+ u64 num_wait:20;
+ u64 reserved_20_31:12;
+ u64 time_wait:16;
+ u64 reserved_48_63:16;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_done_ena_w1s
+ *
+ * CPT Queue Done Interrupt Enable Set Registers
+ * Write 1 to these registers will enable the DONEINT interrupt for the queue.
+ * cptx_vqx_done_ena_w1s_s
+ * Word0
+ * reserved_1_63:63 [63:1] Reserved.
+ * done:1 [0:0](R/W1S/H) Write 1 will enable DONEINT for this queue.
+ * Write 0 has no effect. Read will return the enable bit.
+ */
+union cptx_vqx_done_ena_w1s {
+ u64 u;
+ struct cptx_vqx_done_ena_w1s_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_1_63:63;
+ u64 done:1;
+#else /* Word 0 - Little Endian */
+ u64 done:1;
+ u64 reserved_1_63:63;
+#endif /* Word 0 - End */
+ } s;
+};
+
+/**
+ * Register (NCB) cpt#_vq#_ctl
+ *
+ * CPT VF Queue Control Registers
+ * This register configures queues. This register should be changed (other than
+ * clearing [ENA]) only when quiescent (see CPT()_VQ()_INPROG[INFLIGHT]).
+ * cptx_vqx_ctl_s
+ * Word0
+ * reserved_1_63:63 [63:1] Reserved.
+ * ena:1 [0:0](R/W/H) Enables the logical instruction queue.
+ * See also CPT()_PF_Q()_CTL[CONT_ERR] and CPT()_VQ()_INPROG[INFLIGHT].
+ * 1 = Queue is enabled.
+ * 0 = Queue is disabled.
+ */
+union cptx_vqx_ctl {
+ u64 u;
+ struct cptx_vqx_ctl_s {
+#if defined(__BIG_ENDIAN_BITFIELD) /* Word 0 - Big Endian */
+ u64 reserved_1_63:63;
+ u64 ena:1;
+#else /* Word 0 - Little Endian */
+ u64 ena:1;
+ u64 reserved_1_63:63;
+#endif /* Word 0 - End */
+ } s;
+};
+#endif /*__CPT_HW_TYPES_H*/
diff --git a/drivers/crypto/cavium/cpt/cptpf.h b/drivers/crypto/cavium/cpt/cptpf.h
new file mode 100644
index 0000000..4511a21
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/cptpf.h
@@ -0,0 +1,69 @@
+/*
+ * Copyright (C) 2016 Cavium, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify it
+ * under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#ifndef __CPTPF_H
+#define __CPTPF_H
+
+#include "cpt_common.h"
+
+#define CSR_DELAY 30
+#define CPT_MAX_CORE_GROUPS 8
+#define CPT_MAX_SE_CORES 10
+#define CPT_MAX_AE_CORES 6
+#define CPT_MAX_TOTAL_CORES (CPT_MAX_SE_CORES + CPT_MAX_AE_CORES)
+#define CPT_MAX_VF_NUM 16
+#define CPT_PF_MSIX_VECTORS 3
+#define CPT_PF_INT_VEC_E_MBOXX(a) (0x02 + (a))
+
+struct cpt_device;
+
+struct microcode {
+ u8 is_mc_valid;
+ u8 is_ae;
+ u8 group;
+ u8 num_cores;
+ u32 code_size;
+ u64 core_mask;
+ u8 version[32];
+ /* Base info */
+ dma_addr_t phys_base;
+ void *code;
+};
+
+struct cpt_vf_info {
+ u8 state;
+ u8 priority;
+ u8 id;
+ u32 qlen;
+};
+
+/**
+ * cpt device structure
+ */
+struct cpt_device {
+ u16 flags; /**< Flags to hold device status bits */
+ u8 num_vf_en; /**< Number of VFs enabled (0...CPT_MAX_VF_NUM) */
+ struct cpt_vf_info vfinfo[CPT_MAX_VF_NUM]; /* Per VF info */
+
+ void __iomem *reg_base; /* Register start address */
+ /* MSI-X */
+ u8 num_vec;
+ bool msix_enabled;
+ struct msix_entry msix_entries[CPT_PF_MSIX_VECTORS];
+ bool irq_allocated[CPT_PF_MSIX_VECTORS];
+ struct pci_dev *pdev; /**< pci device handle */
+
+ struct microcode mcode[CPT_MAX_CORE_GROUPS];
+ u8 next_mc_idx; /**< next microcode index */
+ u8 next_group;
+ u8 max_se_cores;
+ u8 max_ae_cores;
+};
+
+void cpt_mbox_intr_handler(struct cpt_device *cpt, s32 mbx);
+#endif /* __CPTPF_H */
diff --git a/drivers/crypto/cavium/cpt/cptpf_main.c b/drivers/crypto/cavium/cpt/cptpf_main.c
new file mode 100644
index 0000000..ff6674b
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/cptpf_main.c
@@ -0,0 +1,733 @@
+/*
+ * Copyright (C) 2016 Cavium, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+
+#include <linux/version.h>
+#include <linux/module.h>
+#include <linux/moduleparam.h>
+#include <linux/printk.h>
+#include <linux/device.h>
+#include <linux/interrupt.h>
+#include <linux/firmware.h>
+#include <linux/pci.h>
+
+#include "cptpf.h"
+
+#define DRV_NAME "thunder-cpt"
+#define DRV_VERSION "1.0"
+
+static u32 num_vfs = 4; /* Default 4 VF enabled */
+module_param(num_vfs, uint, 0444);
+MODULE_PARM_DESC(num_vfs, "Number of VFs to enable(1-16)");
+
+static u64 get_mask_from_value(s32 value)
+{
+ u64 mask = 0ULL;
+ s32 i;
+
+ for (i = 0; i < value; i++)
+ mask |= ((u64)1 << i);
+
+ return mask;
+}
+
+/*
+ * Disable cores specified by coremask
+ */
+static void cpt_disable_cores(struct cpt_device *cpt, u64 coremask,
+ u8 type, u8 grp)
+{
+ union cptx_pf_exe_ctl pf_exe_ctl;
+ u32 timeout = 0xFFFFFFFF;
+ u64 grpmask = 0;
+ struct device *dev = &cpt->pdev->dev;
+
+ if (type == AE_TYPES)
+ coremask = (coremask << cpt->max_se_cores);
+
+ /* Disengage the cores from groups */
+ grpmask = cpt_read_csr64(cpt->reg_base, CPTX_PF_GX_EN(0, grp));
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_GX_EN(0, grp),
+ (grpmask & ~coremask));
+ udelay(CSR_DELAY);
+ grp = cpt_read_csr64(cpt->reg_base, CPTX_PF_EXEC_BUSY(0));
+ while (grp & coremask) {
+ dev_err(dev, "Cores still busy %llx", coremask);
+ grp = cpt_read_csr64(cpt->reg_base,
+ CPTX_PF_EXEC_BUSY(0));
+ if (timeout--)
+ break;
+ }
+
+ /* Disable the cores */
+ pf_exe_ctl.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_EXE_CTL(0));
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_EXE_CTL(0),
+ (pf_exe_ctl.u & ~coremask));
+ udelay(CSR_DELAY);
+}
+
+/*
+ * Enable cores specified by coremask
+ */
+static void cpt_enable_cores(struct cpt_device *cpt, u64 coremask,
+ u8 type)
+{
+ union cptx_pf_exe_ctl pf_exe_ctl;
+
+ if (type == AE_TYPES)
+ coremask = (coremask << cpt->max_se_cores);
+
+ pf_exe_ctl.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_EXE_CTL(0));
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_EXE_CTL(0),
+ (pf_exe_ctl.u | coremask));
+ udelay(CSR_DELAY);
+}
+
+static void cpt_configure_group(struct cpt_device *cpt, u8 grp,
+ u64 coremask, u8 type)
+{
+ union cptx_pf_gx_en pf_gx_en = {0};
+
+ if (type == AE_TYPES)
+ coremask = (coremask << cpt->max_se_cores);
+
+ pf_gx_en.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_GX_EN(0, grp));
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_GX_EN(0, grp),
+ (pf_gx_en.u | coremask));
+ udelay(CSR_DELAY);
+}
+
+static void cpt_disable_mbox_interrupts(struct cpt_device *cpt)
+{
+ /* Clear mbox(0) interupts for all vfs */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_MBOX_ENA_W1CX(0, 0), ~0ull);
+}
+
+static void cpt_disable_ecc_interrupts(struct cpt_device *cpt)
+{
+ /* Clear ecc(0) interupts for all vfs */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_ECC0_ENA_W1C(0), ~0ull);
+}
+
+static void cpt_disable_exec_interrupts(struct cpt_device *cpt)
+{
+ /* Clear exec interupts for all vfs */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_EXEC_ENA_W1C(0), ~0ull);
+}
+
+static void cpt_disable_all_interrupts(struct cpt_device *cpt)
+{
+ cpt_disable_mbox_interrupts(cpt);
+ cpt_disable_ecc_interrupts(cpt);
+ cpt_disable_exec_interrupts(cpt);
+}
+
+static void cpt_enable_mbox_interrupts(struct cpt_device *cpt)
+{
+ /* Set mbox(0) interupts for all vfs */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_MBOX_ENA_W1SX(0, 0), ~0ull);
+}
+
+static s32 cpt_load_microcode(struct cpt_device *cpt, struct microcode *mcode)
+{
+ s32 ret = 0, core = 0, shift = 0;
+ u32 total_cores = 0;
+ struct device *dev = &cpt->pdev->dev;
+
+ if (!mcode || !mcode->code) {
+ dev_err(dev, "Either the mcode is null or data is NULL\n");
+ return 1;
+ }
+
+ if (mcode->code_size == 0) {
+ dev_err(dev, "microcode size is 0\n");
+ return 1;
+ }
+
+ /* Assumes 0-9 are SE cores for UCODE_BASE registers and
+ * AE core bases follow
+ */
+ if (mcode->is_ae) {
+ core = CPT_MAX_SE_CORES; /* start couting from 10 */
+ total_cores = CPT_MAX_TOTAL_CORES; /* upto 15 */
+ } else {
+ core = 0; /* start couting from 0 */
+ total_cores = CPT_MAX_SE_CORES; /* upto 9 */
+ }
+
+ /* Point to microcode for each core of the group */
+ for (; core < total_cores ; core++, shift++) {
+ if (mcode->core_mask & (1 << shift)) {
+ cpt_write_csr64(cpt->reg_base,
+ CPTX_PF_ENGX_UCODE_BASE(0, core),
+ (u64)mcode->phys_base);
+ }
+ }
+ return ret;
+}
+
+static s32 do_cpt_init(struct cpt_device *cpt, struct microcode *mcode)
+{
+ s32 ret = 0;
+ struct device *dev = &cpt->pdev->dev;
+
+ /* Make device not ready */
+ cpt->flags &= ~CPT_FLAG_DEVICE_READY;
+ /* Disable All PF interrupts */
+ cpt_disable_all_interrupts(cpt);
+ /* Calculate mcode group and coremasks */
+ if (mcode->is_ae) {
+ if (mcode->num_cores > cpt->max_ae_cores) {
+ dev_err(dev, "Requested for more cores than available AE cores\n");
+ ret = -1;
+ goto cpt_init_fail;
+ }
+
+ if (cpt->next_group >= CPT_MAX_CORE_GROUPS) {
+ dev_err(dev, "Can't load, all eight microcode groups in use");
+ return -ENFILE;
+ }
+
+ mcode->group = cpt->next_group;
+ /* Convert requested cores to mask */
+ mcode->core_mask = get_mask_from_value(mcode->num_cores);
+ cpt_disable_cores(cpt, mcode->core_mask, AE_TYPES,
+ mcode->group);
+ /* Load microcode for AE engines */
+ if (cpt_load_microcode(cpt, mcode)) {
+ dev_err(dev, "Microcode load Failed for %s\n",
+ mcode->version);
+ ret = -1;
+ goto cpt_init_fail;
+ }
+ cpt->next_group++;
+ /* Configure group mask for the mcode */
+ cpt_configure_group(cpt, mcode->group, mcode->core_mask,
+ AE_TYPES);
+ /* Enable AE cores for the group mask */
+ cpt_enable_cores(cpt, mcode->core_mask, AE_TYPES);
+ } else {
+ if (mcode->num_cores > cpt->max_se_cores) {
+ dev_err(dev, "Requested for more cores than available SE cores\n");
+ ret = -1;
+ goto cpt_init_fail;
+ }
+ if (cpt->next_group >= CPT_MAX_CORE_GROUPS) {
+ dev_err(dev, "Can't load, all eight microcode groups in use");
+ return -ENFILE;
+ }
+
+ mcode->group = cpt->next_group;
+ /* Covert requested cores to mask */
+ mcode->core_mask = get_mask_from_value(mcode->num_cores);
+ cpt_disable_cores(cpt, mcode->core_mask, SE_TYPES,
+ mcode->group);
+ /* Load microcode for SE engines */
+ if (cpt_load_microcode(cpt, mcode)) {
+ dev_err(dev, "Microcode load Failed for %s\n",
+ mcode->version);
+ ret = -1;
+ goto cpt_init_fail;
+ }
+ cpt->next_group++;
+ /* Configure group mask for the mcode */
+ cpt_configure_group(cpt, mcode->group, mcode->core_mask,
+ SE_TYPES);
+ /* Enable SE cores for the group mask */
+ cpt_enable_cores(cpt, mcode->core_mask, SE_TYPES);
+ }
+
+ /* Enabled PF mailbox interrupts */
+ cpt_enable_mbox_interrupts(cpt);
+ cpt->flags |= CPT_FLAG_DEVICE_READY;
+
+ return ret;
+
+cpt_init_fail:
+ /* Enabled PF mailbox interrupts */
+ cpt_enable_mbox_interrupts(cpt);
+
+ return ret;
+}
+
+struct ucode_header {
+ u8 version[32];
+ u32 code_length;
+ u32 data_length;
+ u64 sram_address;
+};
+
+static s32 cpt_ucode_load_fw(struct cpt_device *cpt, const u8 *fw, bool is_ae)
+{
+ const struct firmware *fw_entry;
+ struct device *dev = &cpt->pdev->dev;
+ struct ucode_header *ucode;
+ struct microcode *mcode;
+ int j, ret = 0;
+
+ ret = request_firmware(&fw_entry, fw, dev);
+ if (ret)
+ return ret;
+
+ mcode = &cpt->mcode[cpt->next_mc_idx];
+ ucode = (struct ucode_header *)fw_entry->data;
+ memcpy(mcode->version, (u8 *)fw_entry->data, 32);
+ mcode->code_size = ntohl(ucode->code_length) * 2;
+ mcode->is_ae = is_ae;
+ mcode->core_mask = 0ULL;
+ mcode->num_cores = is_ae ? 6 : 10;
+
+ /* Allocate DMAable space */
+ mcode->code = dma_zalloc_coherent(&cpt->pdev->dev, mcode->code_size,
+ &mcode->phys_base, GFP_KERNEL);
+ if (!mcode->code) {
+ dev_err(dev, "Unable to allocate space for microcode");
+ return -ENOMEM;
+ }
+
+ memcpy((void *)mcode->code, (void *)(fw_entry->data + sizeof(*ucode)),
+ mcode->code_size);
+
+ /* Byte swap 64-bit */
+ for (j = 0; j < (mcode->code_size / 8); j++)
+ ((u64 *)mcode->code)[j] = cpu_to_be64(((u64 *)mcode->code)[j]);
+ /* MC needs 16-bit swap */
+ for (j = 0; j < (mcode->code_size / 2); j++)
+ ((u16 *)mcode->code)[j] = cpu_to_be16(((u16 *)mcode->code)[j]);
+
+ dev_dbg(dev, "mcode->code_size = %u\n", mcode->code_size);
+ dev_dbg(dev, "mcode->is_ae = %u\n", mcode->is_ae);
+ dev_dbg(dev, "mcode->num_cores = %u\n", mcode->num_cores);
+ dev_dbg(dev, "mcode->code = %llx\n", (u64)mcode->code);
+ dev_dbg(dev, "mcode->phys_base = %llx\n", mcode->phys_base);
+
+ ret = do_cpt_init(cpt, mcode);
+ if (ret) {
+ dev_err(dev, "do_cpt_init failed with ret: %d\n", ret);
+ return ret;
+ }
+
+ dev_info(dev, "Microcode Loaded %s\n", mcode->version);
+ mcode->is_mc_valid = 1;
+ cpt->next_mc_idx++;
+ release_firmware(fw_entry);
+
+ return ret;
+}
+
+static s32 cpt_ucode_load(struct cpt_device *cpt)
+{
+ s32 ret = 0;
+ struct device *dev = &cpt->pdev->dev;
+
+ ret = cpt_ucode_load_fw(cpt, "cpt8x-mc-ae.out", true);
+ if (ret) {
+ dev_err(dev, "ae:cpt_ucode_load failed with ret: %d\n", ret);
+ return ret;
+ }
+ ret = cpt_ucode_load_fw(cpt, "cpt8x-mc-se.out", false);
+ if (ret) {
+ dev_err(dev, "se:cpt_ucode_load failed with ret: %d\n", ret);
+ return ret;
+ }
+
+ return ret;
+}
+
+static s32 cpt_enable_msix(struct cpt_device *cpt)
+{
+ s32 i, ret;
+
+ cpt->num_vec = CPT_PF_MSIX_VECTORS;
+
+ for (i = 0; i < cpt->num_vec; i++)
+ cpt->msix_entries[i].entry = i;
+
+ ret = pci_enable_msix(cpt->pdev, cpt->msix_entries, cpt->num_vec);
+ if (ret) {
+ dev_err(&cpt->pdev->dev, "Request for #%d msix vectors failed\n",
+ cpt->num_vec);
+ return ret;
+ }
+
+ cpt->msix_enabled = 1;
+ return 0;
+}
+
+static irqreturn_t cpt_mbx0_intr_handler (s32 irq, void *cpt_irq)
+{
+ struct cpt_device *cpt = (struct cpt_device *)cpt_irq;
+
+ cpt_mbox_intr_handler(cpt, 0);
+
+ return IRQ_HANDLED;
+}
+
+static void cpt_disable_msix(struct cpt_device *cpt)
+{
+ if (cpt->msix_enabled) {
+ pci_disable_msix(cpt->pdev);
+ cpt->msix_enabled = 0;
+ cpt->num_vec = 0;
+ }
+}
+
+static void cpt_free_all_interrupts(struct cpt_device *cpt)
+{
+ s32 irq;
+
+ for (irq = 0; irq < cpt->num_vec; irq++) {
+ if (cpt->irq_allocated[irq])
+ free_irq(cpt->msix_entries[irq].vector, cpt);
+ cpt->irq_allocated[irq] = false;
+ }
+}
+
+static void cpt_reset(struct cpt_device *cpt)
+{
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_RESET(0), 1);
+}
+
+static void cpt_find_max_enabled_cores(struct cpt_device *cpt)
+{
+ union cptx_pf_constants pf_cnsts = {0};
+
+ pf_cnsts.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_CONSTANTS(0));
+ cpt->max_se_cores = pf_cnsts.s.se;
+ cpt->max_ae_cores = pf_cnsts.s.ae;
+}
+
+static u32 cpt_check_bist_status(struct cpt_device *cpt)
+{
+ union cptx_pf_bist_status bist_sts = {0};
+
+ bist_sts.u = cpt_read_csr64(cpt->reg_base,
+ CPTX_PF_BIST_STATUS(0));
+
+ return bist_sts.u;
+}
+
+static u64 cpt_check_exe_bist_status(struct cpt_device *cpt)
+{
+ union cptx_pf_exe_bist_status bist_sts = {0};
+
+ bist_sts.u = cpt_read_csr64(cpt->reg_base,
+ CPTX_PF_EXE_BIST_STATUS(0));
+
+ return bist_sts.u;
+}
+
+static void cpt_disable_all_cores(struct cpt_device *cpt)
+{
+ u32 grp, timeout = 0xFFFFFFFF;
+ struct device *dev = &cpt->pdev->dev;
+
+ /* Disengage the cores from groups */
+ for (grp = 0; grp < CPT_MAX_CORE_GROUPS; grp++) {
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_GX_EN(0, grp), 0);
+ udelay(CSR_DELAY);
+ }
+
+ grp = cpt_read_csr64(cpt->reg_base, CPTX_PF_EXEC_BUSY(0));
+ while (grp) {
+ dev_err(dev, "Cores still busy");
+ grp = cpt_read_csr64(cpt->reg_base,
+ CPTX_PF_EXEC_BUSY(0));
+ if (timeout--)
+ break;
+ }
+ /* Disable the cores */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_EXE_CTL(0), 0);
+}
+
+/**
+ * Ensure all cores are disenganed from all groups by
+ * calling cpt_disable_all_cores() before calling this
+ * function.
+ */
+static void cpt_unload_microcode(struct cpt_device *cpt)
+{
+ u32 grp = 0, core;
+
+ /* Free microcode bases and reset group masks */
+ for (grp = 0; grp < CPT_MAX_CORE_GROUPS; grp++) {
+ struct microcode *mcode = &cpt->mcode[grp];
+
+ if (cpt->mcode[grp].code)
+ dma_free_coherent(&cpt->pdev->dev, mcode->code_size,
+ mcode->code, mcode->phys_base);
+ mcode->code = NULL;
+ //mcode->base = NULL;
+ }
+ /* Clear UCODE_BASE registers for all engines */
+ for (core = 0; core < CPT_MAX_TOTAL_CORES; core++)
+ cpt_write_csr64(cpt->reg_base,
+ CPTX_PF_ENGX_UCODE_BASE(0, core), 0ull);
+}
+
+static s32 cpt_device_init(struct cpt_device *cpt)
+{
+ u64 bist;
+ struct device *dev = &cpt->pdev->dev;
+
+ /* Reset the PF when probed first */
+ cpt_reset(cpt);
+ mdelay((100));
+
+ /*Check BIST status*/
+ bist = (u64)cpt_check_bist_status(cpt);
+ if (bist) {
+ dev_err(dev, "RAM BIST failed with code 0x%llx", bist);
+ return -ENODEV;
+ }
+
+ bist = cpt_check_exe_bist_status(cpt);
+ if (bist) {
+ dev_err(dev, "Engine BIST failed with code 0x%llx", bist);
+ return -ENODEV;
+ }
+
+ /*Get CLK frequency*/
+ /*Get max enabled cores */
+ cpt_find_max_enabled_cores(cpt);
+ /*Disable all cores*/
+ cpt_disable_all_cores(cpt);
+ /*Reset device parameters*/
+ cpt->next_mc_idx = 0;
+ cpt->next_group = 0;
+ /* PF is ready */
+ cpt->flags |= CPT_FLAG_DEVICE_READY;
+
+ return 0;
+}
+
+static s32 cpt_register_interrupts(struct cpt_device *cpt)
+{
+ s32 ret;
+ struct device *dev = &cpt->pdev->dev;
+
+ /* Enable MSI-X */
+ ret = cpt_enable_msix(cpt);
+ if (ret)
+ return ret;
+
+ /* Register mailbox interrupt handlers */
+ ret = request_irq(cpt->msix_entries[CPT_PF_INT_VEC_E_MBOXX(0)].vector,
+ cpt_mbx0_intr_handler, 0, "CPT Mbox0", cpt);
+ if (ret)
+ goto fail;
+
+ cpt->irq_allocated[CPT_PF_INT_VEC_E_MBOXX(0)] = true;
+
+ /* Enable mailbox interrupt */
+ cpt_enable_mbox_interrupts(cpt);
+ return 0;
+
+fail:
+ dev_err(dev, "Request irq failed\n");
+ cpt_free_all_interrupts(cpt);
+ return ret;
+}
+
+static void cpt_unregister_interrupts(struct cpt_device *cpt)
+{
+ cpt_free_all_interrupts(cpt);
+ cpt_disable_msix(cpt);
+}
+
+static s32 cpt_sriov_init(struct cpt_device *cpt, s32 num_vfs)
+{
+ s32 pos = 0;
+ s32 err;
+ u16 total_vf_cnt;
+ struct pci_dev *pdev = cpt->pdev;
+
+ pos = pci_find_ext_capability(pdev, PCI_EXT_CAP_ID_SRIOV);
+ if (!pos) {
+ dev_err(&pdev->dev, "SRIOV capability is not found in PCIe config space\n");
+ return -ENODEV;
+ }
+
+ cpt->num_vf_en = num_vfs; /* User requested VFs */
+ pci_read_config_word(pdev, (pos + PCI_SRIOV_TOTAL_VF), &total_vf_cnt);
+ if (total_vf_cnt < cpt->num_vf_en)
+ cpt->num_vf_en = total_vf_cnt;
+
+ if (!total_vf_cnt)
+ return 0;
+
+ /*Enabled the available VFs */
+ err = pci_enable_sriov(pdev, cpt->num_vf_en);
+ if (err) {
+ dev_err(&pdev->dev, "SRIOV enable failed, num VF is %d\n",
+ cpt->num_vf_en);
+ cpt->num_vf_en = 0;
+ return err;
+ }
+
+ /* TODO: Optionally enable static VQ priorities feature */
+
+ dev_info(&pdev->dev, "SRIOV enabled, number of VF available %d\n",
+ cpt->num_vf_en);
+
+ cpt->flags |= CPT_FLAG_SRIOV_ENABLED;
+
+ return 0;
+}
+
+static s32 cpt_probe(struct pci_dev *pdev, const struct pci_device_id *ent)
+{
+ struct device *dev = &pdev->dev;
+ struct cpt_device *cpt;
+ s32 err;
+
+ cpt = devm_kzalloc(dev, sizeof(struct cpt_device), GFP_KERNEL);
+ if (!cpt)
+ return -ENOMEM;
+
+ pci_set_drvdata(pdev, cpt);
+ cpt->pdev = pdev;
+ err = pci_enable_device(pdev);
+ if (err) {
+ dev_err(dev, "Failed to enable PCI device\n");
+ pci_set_drvdata(pdev, NULL);
+ return err;
+ }
+
+ err = pci_request_regions(pdev, DRV_NAME);
+ if (err) {
+ dev_err(dev, "PCI request regions failed 0x%x\n", err);
+ goto cpt_err_disable_device;
+ }
+
+ err = pci_set_dma_mask(pdev, DMA_BIT_MASK(48));
+ if (err) {
+ dev_err(dev, "Unable to get usable DMA configuration\n");
+ goto cpt_err_release_regions;
+ }
+
+ err = pci_set_consistent_dma_mask(pdev, DMA_BIT_MASK(48));
+ if (err) {
+ dev_err(dev, "Unable to get 48-bit DMA for consistent allocations\n");
+ goto cpt_err_release_regions;
+ }
+
+ /* MAP PF's configuration registers */
+ cpt->reg_base = pcim_iomap(pdev, 0, 0);
+ if (!cpt->reg_base) {
+ dev_err(dev, "Cannot map config register space, aborting\n");
+ err = -ENOMEM;
+ goto cpt_err_release_regions;
+ }
+
+ /* CPT device HW initialization */
+ cpt_device_init(cpt);
+
+ /* Register interrupts */
+ err = cpt_register_interrupts(cpt);
+ if (err)
+ goto cpt_err_release_regions;
+
+ err = cpt_ucode_load(cpt);
+ if (err)
+ goto cpt_err_unregister_interrupts;
+
+ /* Configure SRIOV */
+ err = cpt_sriov_init(cpt, num_vfs);
+ if (err)
+ goto cpt_err_unregister_interrupts;
+
+ return 0;
+
+cpt_err_unregister_interrupts:
+ cpt_unregister_interrupts(cpt);
+cpt_err_release_regions:
+ pci_release_regions(pdev);
+cpt_err_disable_device:
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+ return err;
+}
+
+static void cpt_remove(struct pci_dev *pdev)
+{
+ struct cpt_device *cpt = pci_get_drvdata(pdev);
+
+ /* Disengage SE and AE cores from all groups*/
+ cpt_disable_all_cores(cpt);
+ /* Unload microcodes */
+ cpt_unload_microcode(cpt);
+ cpt_unregister_interrupts(cpt);
+ pci_disable_sriov(pdev);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+}
+
+static void cpt_shutdown(struct pci_dev *pdev)
+{
+ struct cpt_device *cpt = pci_get_drvdata(pdev);
+
+ if (!cpt)
+ return;
+
+ dev_info(&pdev->dev, "Shutdown device %x:%x.\n",
+ (u32)pdev->vendor, (u32)pdev->device);
+
+ cpt_unregister_interrupts(cpt);
+ pci_release_regions(pdev);
+ pci_disable_device(pdev);
+ pci_set_drvdata(pdev, NULL);
+ kzfree(cpt);
+}
+
+/* Supported devices */
+static const struct pci_device_id cpt_id_table[] = {
+ { PCI_DEVICE(PCI_VENDOR_ID_CAVIUM, CPT_81XX_PCI_PF_DEVICE_ID) },
+ { 0, } /* end of table */
+};
+
+static struct pci_driver cpt_pci_driver = {
+ .name = DRV_NAME,
+ .id_table = cpt_id_table,
+ .probe = cpt_probe,
+ .remove = cpt_remove,
+ .shutdown = cpt_shutdown,
+};
+
+static s32 __init cpt_init_module(void)
+{
+ s32 ret = -1;
+
+ pr_info("%s, ver %s\n", DRV_NAME, DRV_VERSION);
+
+ if (num_vfs > 16) {
+ pr_warn("Invalid vf count %d, Resetting it to 1(default)\n",
+ num_vfs);
+ num_vfs = 4;
+ }
+
+ ret = pci_register_driver(&cpt_pci_driver);
+ if (ret)
+ pr_err("pci_register_driver() failed");
+
+ return ret;
+}
+
+static void __exit cpt_cleanup_module(void)
+{
+ pci_unregister_driver(&cpt_pci_driver);
+}
+
+module_init(cpt_init_module);
+module_exit(cpt_cleanup_module);
+
+MODULE_AUTHOR("George Cherian <george.cherian@xxxxxxxxxx>");
+MODULE_DESCRIPTION("Cavium Thunder CPT Physical Function Driver");
+MODULE_LICENSE("GPL v2");
+MODULE_VERSION(DRV_VERSION);
+MODULE_DEVICE_TABLE(pci, cpt_id_table);
diff --git a/drivers/crypto/cavium/cpt/cptpf_mbox.c b/drivers/crypto/cavium/cpt/cptpf_mbox.c
new file mode 100644
index 0000000..1039a5f
--- /dev/null
+++ b/drivers/crypto/cavium/cpt/cptpf_mbox.c
@@ -0,0 +1,163 @@
+/*
+ * Copyright (C) 2016 Cavium, Inc.
+ *
+ * This program is free software; you can redistribute it and/or modify
+ * it under the terms of version 2 of the GNU General Public License
+ * as published by the Free Software Foundation.
+ */
+#include <linux/module.h>
+#include "cptpf.h"
+
+static void cpt_send_msg_to_vf(struct cpt_device *cpt, s32 vf,
+ struct cpt_mbox *mbx)
+{
+ /* Writing mbox(0) causes interrupt */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_VFX_MBOXX(0, vf, 1),
+ mbx->data);
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_VFX_MBOXX(0, vf, 0), mbx->msg);
+}
+
+/* ACKs VF's mailbox message
+ * @vf: VF to which ACK to be sent
+ */
+static void cpt_mbox_send_ack(struct cpt_device *cpt, s32 vf,
+ struct cpt_mbox *mbx)
+{
+ mbx->data = 0ull;
+ mbx->msg = CPT_MBOX_MSG_TYPE_ACK;
+ cpt_send_msg_to_vf(cpt, vf, mbx);
+}
+
+static void cpt_clear_mbox_intr(struct cpt_device *cpt, u32 vf)
+{
+ /* W1C for the VF */
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_MBOX_INTX(0, 0), (1 << vf));
+}
+
+/*
+ * Configure QLEN/Chunk sizes for VF
+ */
+static void cpt_cfg_qlen_for_vf(struct cpt_device *cpt, s32 vf, u32 size)
+{
+ union cptx_pf_qx_ctl pf_qx_ctl;
+
+ pf_qx_ctl.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, vf));
+ pf_qx_ctl.s.size = size;
+ pf_qx_ctl.s.cont_err = true;
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, vf), pf_qx_ctl.u);
+}
+
+/*
+ * Configure VQ priority
+ */
+static void cpt_cfg_vq_priority(struct cpt_device *cpt, s32 vf, u32 pri)
+{
+ union cptx_pf_qx_ctl pf_qx_ctl;
+
+ pf_qx_ctl.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, vf));
+ pf_qx_ctl.s.pri = pri;
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, vf), pf_qx_ctl.u);
+}
+
+static u8 cpt_bind_vq_to_grp(struct cpt_device *cpt, u8 q, u8 grp)
+{
+ struct microcode *mcode = cpt->mcode;
+ union cptx_pf_qx_ctl pf_qx_ctl;
+ struct device *dev = &cpt->pdev->dev;
+
+ if (q >= CPT_MAX_VF_NUM) {
+ dev_err(dev, "Queues are more than cores in the group");
+ return -EINVAL;
+ }
+ if (grp >= CPT_MAX_CORE_GROUPS) {
+ dev_err(dev, "Request group is more than possible groups");
+ return -EINVAL;
+ }
+ if (grp >= cpt->next_mc_idx) {
+ dev_err(dev, "Request group is higher than available functional groups");
+ return -EINVAL;
+ }
+ pf_qx_ctl.u = cpt_read_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, q));
+ pf_qx_ctl.s.grp = mcode[grp].group;
+ cpt_write_csr64(cpt->reg_base, CPTX_PF_QX_CTL(0, q), pf_qx_ctl.u);
+ dev_dbg(dev, "VF %d TYPE %s", q, (mcode[grp].is_ae ? "AE" : "SE"));
+
+ return mcode[grp].is_ae ? AE_TYPES : SE_TYPES;
+}
+
+/* Interrupt handler to handle mailbox messages from VFs */
+static void cpt_handle_mbox_intr(struct cpt_device *cpt, s32 vf)
+{
+ struct cpt_vf_info *vfx = &cpt->vfinfo[vf];
+ struct cpt_mbox mbx = {};
+ u8 vftype;
+ struct device *dev = &cpt->pdev->dev;
+ /*
+ * MBOX[0] contains msg
+ * MBOX[1] contains data
+ */
+ mbx.msg = cpt_read_csr64(cpt->reg_base, CPTX_PF_VFX_MBOXX(0, vf, 0));
+ mbx.data = cpt_read_csr64(cpt->reg_base, CPTX_PF_VFX_MBOXX(0, vf, 1));
+ dev_dbg(dev, "%s: Mailbox msg 0x%llx from VF%d", __func__, mbx.msg, vf);
+ switch (mbx.msg) {
+ case CPT_MSG_VF_UP:
+ vfx->state = VF_STATE_UP;
+ try_module_get(THIS_MODULE);
+ cpt_mbox_send_ack(cpt, vf, &mbx);
+ break;
+ case CPT_MSG_READY:
+ mbx.msg = CPT_MSG_READY;
+ mbx.data = vf;
+ cpt_send_msg_to_vf(cpt, vf, &mbx);
+ break;
+ case CPT_MSG_VF_DOWN:
+ /* First msg in VF teardown sequence */
+ vfx->state = VF_STATE_DOWN;
+ module_put(THIS_MODULE);
+ cpt_mbox_send_ack(cpt, vf, &mbx);
+ break;
+ case CPT_MSG_QLEN:
+ vfx->qlen = mbx.data;
+ cpt_cfg_qlen_for_vf(cpt, vf, vfx->qlen);
+ cpt_mbox_send_ack(cpt, vf, &mbx);
+ break;
+ case CPT_MSG_QBIND_GRP:
+ vftype = cpt_bind_vq_to_grp(cpt, vf, (u8)mbx.data);
+ if ((vftype != AE_TYPES) && (vftype != SE_TYPES))
+ dev_err(dev, "Queue %d binding to group %llu failed",
+ vf, mbx.data);
+ else {
+ dev_dbg(dev, "Queue %d binding to group %llu successful",
+ vf, mbx.data);
+ mbx.msg = CPT_MSG_QBIND_GRP;
+ mbx.data = vftype;
+ cpt_send_msg_to_vf(cpt, vf, &mbx);
+ }
+ break;
+ case CPT_MSG_VQ_PRIORITY:
+ vfx->priority = mbx.data;
+ cpt_cfg_vq_priority(cpt, vf, vfx->priority);
+ cpt_mbox_send_ack(cpt, vf, &mbx);
+ break;
+ default:
+ dev_err(&cpt->pdev->dev, "Invalid msg from VF%d, msg 0x%llx\n",
+ vf, mbx.msg);
+ break;
+ }
+}
+
+void cpt_mbox_intr_handler (struct cpt_device *cpt, s32 mbx)
+{
+ u64 intr;
+ u8 vf;
+
+ intr = cpt_read_csr64(cpt->reg_base, CPTX_PF_MBOX_INTX(0, 0));
+ dev_dbg(&cpt->pdev->dev, "PF interrupt Mbox%d 0x%llx\n", mbx, intr);
+ for (vf = 0; vf < CPT_MAX_VF_NUM; vf++) {
+ if (intr & (1ULL << vf)) {
+ dev_dbg(&cpt->pdev->dev, "Intr from VF %d\n", vf);
+ cpt_handle_mbox_intr(cpt, vf);
+ cpt_clear_mbox_intr(cpt, vf);
+ }
+ }
+}
--
2.1.4