Re: [PATCH v2 4/6] pinctrl: aspeed: Read and write bits in LPCHC and GFX controllers

From: Rob Herring
Date: Wed Nov 09 2016 - 13:27:24 EST


On Thu, Nov 03, 2016 at 01:07:59AM +1030, Andrew Jeffery wrote:
> The System Control Unit IP block in the Aspeed SoCs is typically where
> the pinmux configuration is found, but not always. A number of pins
> depend on state in one of LPC Host Control (LPCHC) or SoC Display
> Controller (GFX) IP blocks, so the Aspeed pinmux drivers should have the
> means to adjust these as necessary.
>
> We use syscon to cast a regmap over the GFX and LPCHCR blocks, which is
> used as an arbitration layer between the relevant driver and the pinctrl
> subsystem. The regmaps are then exposed to the SoC-specific pinctrl
> drivers by phandles in the devicetree, and are selected during a mux
> request by querying a new 'ip' member in struct aspeed_sig_desc.
>
> Signed-off-by: Andrew Jeffery <andrew@xxxxxxxx>
> ---
> Since v1:
>
> The change is now proactive: instead of reporting that we need to flip bits in
> controllers we can't access, the patch provides access via regmaps for the
> relevant controllers. The implementation also splits out the IP block ID into
> its own variable rather than packing the value into the upper bits of the reg
> member of struct aspeed_sig_desc. This drives some churn in the diff, but I've
> tried to minimise it.
>
> .../devicetree/bindings/pinctrl/pinctrl-aspeed.txt | 50 +++++++++++++---
> drivers/pinctrl/aspeed/pinctrl-aspeed-g4.c | 18 +++---
> drivers/pinctrl/aspeed/pinctrl-aspeed-g5.c | 39 ++++++++++---
> drivers/pinctrl/aspeed/pinctrl-aspeed.c | 66 +++++++++++++---------
> drivers/pinctrl/aspeed/pinctrl-aspeed.h | 32 ++++++++---
> 5 files changed, 144 insertions(+), 61 deletions(-)
>
> diff --git a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> index 2ad18c4ea55c..115b0cce6c1c 100644
> --- a/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> +++ b/Documentation/devicetree/bindings/pinctrl/pinctrl-aspeed.txt
> @@ -4,12 +4,19 @@ Aspeed Pin Controllers
> The Aspeed SoCs vary in functionality inside a generation but have a common mux
> device register layout.
>
> -Required properties:
> -- compatible : Should be any one of the following:
> - "aspeed,ast2400-pinctrl"
> - "aspeed,g4-pinctrl"
> - "aspeed,ast2500-pinctrl"
> - "aspeed,g5-pinctrl"
> +Required properties for g4:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2400-pinctrl"
> + "aspeed,g4-pinctrl"
> +
> +Required properties for g5:
> +- compatible : Should be any one of the following:
> + "aspeed,ast2500-pinctrl"
> + "aspeed,g5-pinctrl"
> +
> +- aspeed,external-nodes: A cell of phandles to external controller nodes:
> + 0: compatible with "aspeed,ast2500-gfx", "syscon"
> + 1: compatible with "aspeed,ast2500-lpchc", "syscon"
>
> The pin controller node should be a child of a syscon node with the required
> property:
> @@ -47,7 +54,7 @@ RGMII1 RGMII2 RMII1 RMII2 SD1 SPI1 SPI1DEBUG SPI1PASSTHRU TIMER4 TIMER5 TIMER6
> TIMER7 TIMER8 VGABIOSROM
>
>
> -Examples:
> +g4 Example:
>
> syscon: scu@1e6e2000 {
> compatible = "syscon", "simple-mfd";
> @@ -63,5 +70,34 @@ syscon: scu@1e6e2000 {
> };
> };
>
> +g5 Example:
> +
> +apb {
> + gfx: display@1e6e6000 {
> + compatible = "aspeed,ast2500-gfx", "syscon";
> + reg = <0x1e6e6000 0x1000>;
> + };
> +
> + lpchc: lpchc@1e7890a0 {
> + compatible = "aspeed,ast2500-lpchc", "syscon";
> + reg = <0x1e7890a0 0xc4>;
> + };
> +
> + syscon: scu@1e6e2000 {
> + compatible = "syscon", "simple-mfd";
> + reg = <0x1e6e2000 0x1a8>;
> +
> + pinctrl: pinctrl {

Why the single child node here? Doesn't look like any reason for it in
the example.

> + compatible = "aspeed,g5-pinctrl";
> + aspeed,external-nodes = <&gfx, &lpchc>;
> +
> + pinctrl_i2c3_default: i2c3_default {
> + function = "I2C3";
> + groups = "I2C3";
> + };
> + };
> + };
> +};
> +
> Please refer to pinctrl-bindings.txt in this directory for details of the
> common pinctrl bindings used by client devices.