Re: [PATCH] sdhci-esdhc-imx: fix bus-width for 1-bit operation.

From: Stefan Agner
Date: Wed Nov 02 2016 - 12:46:12 EST


On 2016-11-02 01:42, Dong Aisheng wrote:
> Hi Leonardo,
>
> On Tue, Nov 1, 2016 at 11:58 PM, Leonardo G. Veiga <leogveiga@xxxxxxxxx> wrote:
>> From: Leonardo Graboski Veiga <leonardo.veiga@xxxxxxxxxxx>
>>
>> The 1-bit operation mode, enabled by seeting the 'bus-width' property of
>> the device tree 'esdhc' node to <1>, not work while using SD card.
>>
>> The behavior is only noticed when only the data pin 0 is connected to the
>> hardware. A series of kernel errors are printed to the console, all of them
>> returning the following error message followed by some explanation:
>> mmcblk0: error -84 transferring data
>>
>> If four data lines are connected, it ignores the device-tree
>> property and works in 4-bit mode of operation without errors. The hardware
>> used for testing does not support 8-bit mode.
>>
>> Check the 'bus-width' property and if set to <1>, enable the
>> SDHCI_QUIRK_FORCE_1_BIT_DATA quirk.
>>
>> Signed-off-by: Leonardo Graboski Veiga <leonardo.veiga@xxxxxxxxxxx>
>> ---
>> drivers/mmc/host/sdhci-esdhc-imx.c | 4 ++++
>> 1 file changed, 4 insertions(+)
>>
>> diff --git a/drivers/mmc/host/sdhci-esdhc-imx.c b/drivers/mmc/host/sdhci-esdhc-imx.c
>> index c9fbc4c3..88d7d22 100644
>> --- a/drivers/mmc/host/sdhci-esdhc-imx.c
>> +++ b/drivers/mmc/host/sdhci-esdhc-imx.c
>> @@ -1003,6 +1003,10 @@ sdhci_esdhc_imx_probe_dt(struct platform_device *pdev,
>> host->quirks2 |= SDHCI_QUIRK2_NO_1_8_V;
>> }
>>
>> + if (!of_property_read_u32(np, "bus-width", &boarddata->max_bus_width)
>> + && boarddata->max_bus_width == 1)
>> + host->quirks |= SDHCI_QUIRK_FORCE_1_BIT_DATA;
>> +
>
> This looks like a common SDHCI driver issue that it assumes the default
> bus-width as 4 bit if no SDHCI_QUIRK_FORCE_1_BIT_DATA specified.
> if (!(host->quirks & SDHCI_QUIRK_FORCE_1_BIT_DATA))
> mmc->caps |= MMC_CAP_4_BIT_DATA;
>
> And I'm not sure Andrian or Ulf would like to see people keep using this quirk.
> IMHO we probably could totally remove it since bus-width already tells
> what the driver needs.

Hm, I see what you are saying, the problem is that the core
(sdhci_setup_host) falls back to 4-bit if SDHCI_QUIRK_FORCE_1_BIT_DATA
is not set... Removing that should be fine for DT enabled SDHC drivers,
since mmc_of_parse sets MMC_CAP_4_BIT_DATA. But not sure about drivers
which parse dt on their own or still support platform data.... Those
might rely on MMC_CAP_4_BIT_DATA being set by default...

--
Stefan



>
> Andrian & Ulf,
> Comments?
>
>> /* call to generic mmc_of_parse to support additional capabilities */
>> ret = mmc_of_parse(host->mmc);
>> if (ret)
>> --
>> 2.7.4
>>
>
> Regards
> Dong Aisheng