[PATCH 2/3] ARM: dts: sun8i: Use the common file in NanoPi NEO SBC

From: Milo Kim
Date: Thu Oct 20 2016 - 04:09:05 EST


Cc: James Pettigrew <james@xxxxxxxxxxxxxx>
Signed-off-by: Milo Kim <woogyom.kim@xxxxxxxxx>
---
arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts | 79 +------------------------------
1 file changed, 1 insertion(+), 78 deletions(-)

diff --git a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
index 3d64caf..8d2cc6e 100644
--- a/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
+++ b/arch/arm/boot/dts/sun8i-h3-nanopi-neo.dts
@@ -40,86 +40,9 @@
* OTHER DEALINGS IN THE SOFTWARE.
*/

-/dts-v1/;
-#include "sun8i-h3.dtsi"
-#include "sunxi-common-regulators.dtsi"
-
-#include <dt-bindings/gpio/gpio.h>
-#include <dt-bindings/pinctrl/sun4i-a10.h>
+#include "sun8i-h3-nanopi.dtsi"

/ {
model = "FriendlyARM NanoPi NEO";
compatible = "friendlyarm,nanopi-neo", "allwinner,sun8i-h3";
-
- aliases {
- serial0 = &uart0;
- };
-
- chosen {
- stdout-path = "serial0:115200n8";
- };
-
- leds {
- compatible = "gpio-leds";
- pinctrl-names = "default";
- pinctrl-0 = <&leds_opc>, <&leds_r_opc>;
-
- pwr {
- label = "nanopi:green:pwr";
- gpios = <&r_pio 0 10 GPIO_ACTIVE_HIGH>; /* PL10 */
- default-state = "on";
- };
-
- status {
- label = "nanopi:blue:status";
- gpios = <&pio 0 10 GPIO_ACTIVE_HIGH>; /* PA10 */
- };
- };
-};
-
-&ehci3 {
- status = "okay";
-};
-
-&mmc0 {
- pinctrl-names = "default";
- pinctrl-0 = <&mmc0_pins_a>, <&mmc0_cd_pin>;
- vmmc-supply = <&reg_vcc3v3>;
- bus-width = <4>;
- cd-gpios = <&pio 5 6 GPIO_ACTIVE_HIGH>; /* PF6 */
- cd-inverted;
- status = "okay";
-};
-
-&ohci3 {
- status = "okay";
-};
-
-&pio {
- leds_opc: led-pins {
- allwinner,pins = "PA10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
-&r_pio {
- leds_r_opc: led-pins {
- allwinner,pins = "PL10";
- allwinner,function = "gpio_out";
- allwinner,drive = <SUN4I_PINCTRL_10_MA>;
- allwinner,pull = <SUN4I_PINCTRL_NO_PULL>;
- };
-};
-
-&uart0 {
- pinctrl-names = "default";
- pinctrl-0 = <&uart0_pins_a>;
- status = "okay";
-};
-
-&usbphy {
- /* USB VBUS is always on */
- status = "okay";
};
--
2.9.3