Re: [PATCH v2 6/7] arm64: dts: exynos: Add dts file for Exynos5433-based TM2 board

From: Chanwoo Choi
Date: Fri Sep 02 2016 - 07:29:38 EST


Hi Javier,

On 2016ë 08ì 27ì 03:30, Javier Martinez Canillas wrote:
> Hello Chanwoo,
>
> The patch looks mostly good to me, I've just some comments:
>
> [snip]
>
>> +
>> +&decon {
>> + status = "okay";
>> + iommu-reserved-mapping = <0x20000000 0x20000000 0xc0000000>;
>> +
>
> This property never made to mainline due not having an agreement on
> how this should be fixed properly IIUC [0]. So you should remove it.

OK. I'll remove it.

>
> [snip]
>
>> +
>> + s2mps13-pmic@66 {
>> + compatible = "samsung,s2mps13-pmic";
>> + interrupt-parent = <&gpa0>;
>> + interrupts = <7 IRQ_TYPE_NONE>;
>> + reg = <0x66>;
>> + samsung,s2mps11-wrstbi-ground;
>> +
>> + s2mps13_osc: clocks {
>> + compatible = "samsung,s2mps13-clk";
>> + #clock-cells = <1>;
>> + clock-output-names = "s2mps13_ap", "s2mps13_cp",
>> + "s2mps13_bt";
>> + };
>> +
>
> I see that most of the following regulators are marked as always-on
> but I wonder if this is really needed. For example some of them are
> looked up by consumer devices.
>
> [snip]
>
>> + };
>> +
>> + ldo3_reg: LDO3 {
>> + regulator-name = "VDD1_E_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>> + };
>
> This is used by both the ADC and the TMU so I guess it should be safe
> to not mark it as always-on (unless is used by other critical IP block
> not described in the DT).

This regulator should be always ON state.
This regulator provides the voltage to ALIVE domain of Exynos5433.

>
> [snip]
>
>> +
>> + ldo6_reg: LDO6 {
>> + regulator-name = "VDD10_MIPI2L_1.0V_AP";
>> + regulator-min-microvolt = <1000000>;
>> + regulator-max-microvolt = <1000000>;
>> + regulator-always-on;
>
> Same question, this is used by both the dsi and usbdrd30 nodes so maybe
> it shouldn't be marked as always-on as well.

OK. I'll remove it.

>
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + ldo7_reg: LDO7 {
>> + regulator-name = "VDD18_MIPI2L_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>
> This is used by the dsi node as well.

OK. I'll remove it.

>
> [snip]
>
>> +
>> + ldo10_reg: LDO10 {
>> + regulator-name = "VDD33_USB30_3.0V_AP";
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3000000>;
>> + regulator-always-on;
>
> Use by the usbdrd30 node.

OK. I'll remove it.

>
> [snip]
>
>> +
>> + ldo18_reg: LDO18 {
>> + regulator-name = "V_CODEC_1.8V_AP";
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1800000>;
>> + regulator-always-on;
>
> Use by the wm5110-codec node.

OK. I'll remove it.

>
> [snip]
>
>> +
>> + buck2_reg: BUCK2 {
>> + regulator-name = "VDD_EGL_1.0V_AP";
>
> I wonder if this shouldn't be "VDD_ATL_1.0V_AP" or something since
> the big cluster isn't called Eagle like in arm32 Exynos but Atlas?

I used the regulator's name according to TM2's schematic.
As I knew, Eagle means the big cores.

>
>> + regulator-min-microvolt = <900000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>> + buck3_reg: BUCK3 {
>> + regulator-name = "VDD_KFC_1.0V_AP";
>
> Same, maybe using "VDD_APL_1.0V_AP" since the big cluster is Apollo?

ditto.
The KFC (King Fisher) means the little cores.

>
>> + regulator-min-microvolt = <800000>;
>> + regulator-max-microvolt = <1200000>;
>> + regulator-always-on;
>> + regulator-state-mem {
>> + regulator-off-in-suspend;
>> + };
>> + };
>> +
>
> Used by the big and LITTLE clusters respectively, although for these two
> I'm not that sure if it would be safe to remove the always-on property.

>
> Reviewed-by: Javier Martinez Canillas <javier@xxxxxxxxxxxxxxx>

Thanks for your review.

>
> [0]: http://www.spinics.net/lists/arm-kernel/msg419747.html
>
> Best regards,
>
--
Best Regards,
Chanwoo Choi