Re: [linux-sunxi] [PATCH v2 14/14] ARM: dts: sun8i: Enable DVFS on Orange Pi One

From: OndÅej Jirman
Date: Thu Jun 30 2016 - 11:53:50 EST


On 30.6.2016 17:50, Michal Suchanek wrote:
> On 30 June 2016 at 17:16, Michal Suchanek <hramrach@xxxxxxxxx> wrote:
>> On 30 June 2016 at 16:19, OndÅej Jirman <megous@xxxxxxxxxx> wrote:
>>> Hello,
>>>
>>> On 30.6.2016 13:13, Michal Suchanek wrote:
>>>> Hello,
>>>>
>>>> On 25 June 2016 at 05:45, <megous@xxxxxxxxxx> wrote:
>>>>> From: Ondrej Jirman <megous@xxxxxxxxxx>
>>>>>
>>>>> Use Xulong Orange Pi One GPIO based regulator for
>>>>> passive cooling and thermal management.
>>>>>
>>>>> Signed-off-by: Ondrej Jirman <megous@xxxxxxxxxx>
>>>>> ---
>>>>> arch/arm/boot/dts/sun8i-h3-orangepi-one.dts | 39 +++++++++++++++++++++++++++++
>>>>> 1 file changed, 39 insertions(+)
>>>>>
>>>>> diff --git a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>>> index b1bd6b0..a38d871 100644
>>>>> --- a/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>>> +++ b/arch/arm/boot/dts/sun8i-h3-orangepi-one.dts
>>>>> @@ -109,6 +109,45 @@
>>>>> };
>>>>> };
>>>>>
>>>>> +&cpu0 {
>>>>> + operating-points = <
>>>>> + /* kHz uV */
>>>>> + 1296000 1300000
>>>>> + 1200000 1300000
>>>>
>>>> First problem is that the board boots at 1008000 which is not listed
>>>> and the kernel complains.
>>>>
>>>> Second problem is that the board locks up during boot with this enabled.
>>>>
>>>> Do you have some suggestion for alternate configuration to test?
>>>
>>> Just to verify, did you test with the entire series applied? (especially
>>> the PLL1 clk application changes)
>>
>> Yes, I applied the whole series.
>>
>>>
>>> You may try dropping the highest operating point, it's probably overly
>>> optimistic for Orange Pi One.
>>>
>>> Is the power supply/cable you're using hard enough?
>>
>> I use a 7 port hub to power the board. It worked with some other small
>> devboards.
>>
>> The cable is some random Chinese USB to power jack adaptor with an
>> extra adaptor to fit the Pi socket. It looks ok but I did not test
>> this particular combination thoroughly.
>>
>>>
>>> Where during the boot process does it lock up?
>>
>> Usually sometime around enabling cpufreq before getty starts.
>> Different runs and settings give slightly different results. In
>> particular adding the 1008000 point seems to make it go further.
>>
>> Removing all traces of the regulator, cpufreq and thermal I can boot
>> pretty much 100% to login prompt.
>>
>> I don't think the difference between 1GHz and 1.3GHz frequency on the
>> core would put much additional stress on the supply but I can try with
>> 35W PSU and some alternative cabling to be sure.
>>
>> I did some more tests and it seems 1008000@xxxx is fine but switching
>> to 1.3V crashes the board. Even with only the first 1.3V state. Maybe
>> there is need for some delay somewhere for the regulator to get
>> stable?
>>
>
> Hm, the AW table shows 1008000@xxxx as supported state and it indeed
> works. So the voltage switching works or does nothing. Can I measure
> the regulator output somewhere? Clocking the chip higher does not
> work.

Regulator output is TP1 on the bottom of the board, next ot the CSI
connector.

regards,
Ondrej

> I will try with another PSU later.
>
> Thanks
>
> Michal
>

Attachment: signature.asc
Description: OpenPGP digital signature