Re: [PATCH v3 2/3] iio: Add driver for Broadcom iproc-static-adc
From: Jonathan Cameron
Date: Mon Jun 27 2016 - 15:11:37 EST
On 27/06/16 07:25, Raveendra Padasalagi wrote:
> On Sun, Jun 26, 2016 at 4:08 PM, Jonathan Cameron <jic23@xxxxxxxxxx> wrote:
>> On 22/06/16 07:11, Raveendra Padasalagi wrote:
>>> This patch adds basic driver implementation for Broadcom's
>>> static adc controller used in iProc SoC's family.
>>>
>>> Signed-off-by: Raveendra Padasalagi <raveendra.padasalagi@xxxxxxxxxxxx>
>>> Reviewed-by: Ray Jui <ray.jui@xxxxxxxxxxxx>
>>> Reviewed-by: Scott Branden <scott.branden@xxxxxxxxxxxx>
>> A few tiny nitpicks.. Otherwise, looking good to me.
>>
>> Thanks,
>>
>> Jonathan
>
> Thank you. I have provided my view on naming "indio_dev->name" below.
> Need your opinion/suggestion on the same to address it.
>
>>> ---
>>> drivers/iio/adc/Kconfig | 12 +
>>> drivers/iio/adc/Makefile | 1 +
>>> drivers/iio/adc/bcm_iproc_adc.c | 648 ++++++++++++++++++++++++++++++++++++++++
>>> 3 files changed, 661 insertions(+)
>>> create mode 100644 drivers/iio/adc/bcm_iproc_adc.c
>>>
>>> diff --git a/drivers/iio/adc/Kconfig b/drivers/iio/adc/Kconfig
>>> index 25378c5..1de31bd 100644
>>> --- a/drivers/iio/adc/Kconfig
>>> +++ b/drivers/iio/adc/Kconfig
>>> @@ -153,6 +153,18 @@ config AXP288_ADC
>>> To compile this driver as a module, choose M here: the module will be
>>> called axp288_adc.
>>>
>>> +config BCM_IPROC_ADC
>>> + tristate "Broadcom IPROC ADC driver"
>>> + depends on ARCH_BCM_IPROC || COMPILE_TEST
>>> + depends on MFD_SYSCON
>>> + default ARCH_BCM_CYGNUS
>>> + help
>>> + Say Y here if you want to add support for the Broadcom static
>>> + ADC driver.
>>> +
>>> + Broadcom iProc ADC driver. Broadcom iProc ADC controller has 8
>>> + channels. The driver allows the user to read voltage values.
>>> +
>>> config BERLIN2_ADC
>>> tristate "Marvell Berlin2 ADC driver"
>>> depends on ARCH_BERLIN
>>> diff --git a/drivers/iio/adc/Makefile b/drivers/iio/adc/Makefile
>>> index 38638d4..0ba0d50 100644
>>> --- a/drivers/iio/adc/Makefile
>>> +++ b/drivers/iio/adc/Makefile
>>> @@ -16,6 +16,7 @@ obj-$(CONFIG_AD799X) += ad799x.o
>>> obj-$(CONFIG_AT91_ADC) += at91_adc.o
>>> obj-$(CONFIG_AT91_SAMA5D2_ADC) += at91-sama5d2_adc.o
>>> obj-$(CONFIG_AXP288_ADC) += axp288_adc.o
>>> +obj-$(CONFIG_BCM_IPROC_ADC) += bcm_iproc_adc.o
>>> obj-$(CONFIG_BERLIN2_ADC) += berlin2-adc.o
>>> obj-$(CONFIG_CC10001_ADC) += cc10001_adc.o
>>> obj-$(CONFIG_DA9150_GPADC) += da9150-gpadc.o
>>> diff --git a/drivers/iio/adc/bcm_iproc_adc.c b/drivers/iio/adc/bcm_iproc_adc.c
>>> new file mode 100644
>>> index 0000000..e10f6ce
>>> --- /dev/null
>>> +++ b/drivers/iio/adc/bcm_iproc_adc.c
>>> @@ -0,0 +1,648 @@
>>> +/*
>>> + * Copyright 2016 Broadcom
>>> + *
>>> + * This program is free software; you can redistribute it and/or modify
>>> + * it under the terms of the GNU General Public License, version 2, as
>>> + * published by the Free Software Foundation (the "GPL").
>>> + *
>>> + * This program is distributed in the hope that it will be useful, but
>>> + * WITHOUT ANY WARRANTY; without even the implied warranty of
>>> + * MERCHANTABILITY or FITNESS FOR A PARTICULAR PURPOSE. See the GNU
>>> + * General Public License version 2 (GPLv2) for more details.
>>> + *
>>> + * You should have received a copy of the GNU General Public License
>>> + * version 2 (GPLv2) along with this source code.
>>> + */
>>> +
>>> +#include <linux/module.h>
>>> +#include <linux/of.h>
>>> +#include <linux/io.h>
>>> +#include <linux/clk.h>
>>> +#include <linux/mfd/syscon.h>
>>> +#include <linux/regmap.h>
>>> +#include <linux/delay.h>
>>> +#include <linux/interrupt.h>
>>> +#include <linux/platform_device.h>
>>> +
>>> +#include <linux/iio/iio.h>
>>> +
>>> +/* Below Register's are common to IPROC ADC and Touchscreen IP */
>>> +#define IPROC_REGCTL1 0x00
>>> +#define IPROC_REGCTL2 0x04
>>> +#define IPROC_INTERRUPT_THRES 0x08
>>> +#define IPROC_INTERRUPT_MASK 0x0c
>>> +#define IPROC_INTERRUPT_STATUS 0x10
>>> +#define IPROC_ANALOG_CONTROL 0x1c
>>> +#define IPROC_CONTROLLER_STATUS 0x14
>>> +#define IPROC_AUX_DATA 0x20
>>> +#define IPROC_SOFT_BYPASS_CONTROL 0x38
>>> +#define IPROC_SOFT_BYPASS_DATA 0x3C
>>> +
>>> +/* IPROC ADC Channel register offsets */
>>> +#define IPROC_ADC_CHANNEL_REGCTL1 0x800
>>> +#define IPROC_ADC_CHANNEL_REGCTL2 0x804
>>> +#define IPROC_ADC_CHANNEL_STATUS 0x808
>>> +#define IPROC_ADC_CHANNEL_INTERRUPT_STATUS 0x80c
>>> +#define IPROC_ADC_CHANNEL_INTERRUPT_MASK 0x810
>>> +#define IPROC_ADC_CHANNEL_DATA 0x814
>>> +#define IPROC_ADC_CHANNEL_OFFSET 0x20
>>> +
>>> +/* Bit definitions for IPROC_REGCTL2 */
>>> +#define IPROC_ADC_AUXIN_SCAN_ENA BIT(0)
>>> +#define IPROC_ADC_PWR_LDO BIT(5)
>>> +#define IPROC_ADC_PWR_ADC BIT(4)
>>> +#define IPROC_ADC_PWR_BG BIT(3)
>>> +#define IPROC_ADC_CONTROLLER_EN BIT(17)
>>> +
>>> +/* Bit definitions for IPROC_INTERRUPT_MASK and IPROC_INTERRUPT_STATUS */
>>> +#define IPROC_ADC_AUXDATA_RDY_INTR BIT(3)
>>> +#define IPROC_ADC_INTR 9
>>> +#define IPROC_ADC_INTR_MASK (0xFF << IPROC_ADC_INTR)
>>> +
>>> +/* Bit definitions for IPROC_ANALOG_CONTROL */
>>> +#define IPROC_ADC_CHANNEL_SEL 11
>>> +#define IPROC_ADC_CHANNEL_SEL_MASK (0x7 << IPROC_ADC_CHANNEL_SEL)
>>> +
>>> +/* Bit definitions for IPROC_ADC_CHANNEL_REGCTL1 */
>>> +#define IPROC_ADC_CHANNEL_ROUNDS 0x2
>>> +#define IPROC_ADC_CHANNEL_ROUNDS_MASK (0x3F << IPROC_ADC_CHANNEL_ROUNDS)
>>> +#define IPROC_ADC_CHANNEL_MODE 0x1
>>> +#define IPROC_ADC_CHANNEL_MODE_MASK (0x1 << IPROC_ADC_CHANNEL_MODE)
>>> +#define IPROC_ADC_CHANNEL_MODE_TDM 0x1
>>> +#define IPROC_ADC_CHANNEL_MODE_SNAPSHOT 0x0
>>> +#define IPROC_ADC_CHANNEL_ENABLE 0x0
>>> +#define IPROC_ADC_CHANNEL_ENABLE_MASK 0x1
>>> +
>>> +/* Bit definitions for IPROC_ADC_CHANNEL_REGCTL2 */
>>> +#define IPROC_ADC_CHANNEL_WATERMARK 0x0
>>> +#define IPROC_ADC_CHANNEL_WATERMARK_MASK \
>>> + (0x3F << IPROC_ADC_CHANNEL_WATERMARK)
>>> +
>>> +#define IPROC_ADC_WATER_MARK_LEVEL 0x1
>>> +
>>> +/* Bit definitions for IPROC_ADC_CHANNEL_STATUS */
>>> +#define IPROC_ADC_CHANNEL_DATA_LOST 0x0
>>> +#define IPROC_ADC_CHANNEL_DATA_LOST_MASK \
>>> + (0x0 << IPROC_ADC_CHANNEL_DATA_LOST)
>>> +#define IPROC_ADC_CHANNEL_VALID_ENTERIES 0x1
>>> +#define IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK \
>>> + (0xFF << IPROC_ADC_CHANNEL_VALID_ENTERIES)
>>> +#define IPROC_ADC_CHANNEL_TOTAL_ENTERIES 0x9
>>> +#define IPROC_ADC_CHANNEL_TOTAL_ENTERIES_MASK \
>>> + (0xFF << IPROC_ADC_CHANNEL_TOTAL_ENTERIES)
>>> +
>>> +/* Bit definitions for IPROC_ADC_CHANNEL_INTERRUPT_MASK */
>>> +#define IPROC_ADC_CHANNEL_WTRMRK_INTR 0x0
>>> +#define IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK \
>>> + (0x1 << IPROC_ADC_CHANNEL_WTRMRK_INTR)
>>> +#define IPROC_ADC_CHANNEL_FULL_INTR 0x1
>>> +#define IPROC_ADC_CHANNEL_FULL_INTR_MASK \
>>> + (0x1 << IPROC_ADC_IPROC_ADC_CHANNEL_FULL_INTR)
>>> +#define IPROC_ADC_CHANNEL_EMPTY_INTR 0x2
>>> +#define IPROC_ADC_CHANNEL_EMPTY_INTR_MASK \
>>> + (0x1 << IPROC_ADC_CHANNEL_EMPTY_INTR)
>>> +
>>> +#define IPROC_ADC_WATER_MARK_INTR_ENABLE 0x1
>>> +
>>> +/* Number of time to retry a set of the interrupt mask reg */
>>> +#define IPROC_ADC_INTMASK_RETRY_ATTEMPTS 10
>>> +
>>> +#define IPROC_ADC_READ_TIMEOUT (HZ*2)
>>> +
>>> +#define iproc_adc_dbg_reg(dev, priv, reg) \
>>> +do { \
>>> + u32 val; \
>>> + regmap_read(priv->regmap, reg, &val); \
>>> + dev_dbg(dev, "%20s= 0x%08x\n", #reg, val); \
>>> +} while (0)
>>> +
>>> +struct iproc_adc_priv {
>>> + struct regmap *regmap;
>>> + struct clk *adc_clk;
>>> + struct mutex mutex;
>>> + int irqno;
>>> + int chan_val;
>>> + int chan_id;
>>> + struct completion completion;
>>> +};
>>> +
>>> +static void iproc_adc_reg_dump(struct iio_dev *indio_dev)
>>> +{
>>> + struct iproc_adc_priv *adc_priv;
>>> + struct device *dev = &indio_dev->dev;
>>> +
>>> + adc_priv = iio_priv(indio_dev);
>> Trivial, but I'd just do this in one line with the declaration of
>> the local variable.
>>
>> struct iprov_adc_priv *adc_priv = iio_priv(indio_dev);
>
> Yes, I missed it to fix. Will address in the next patch.
> Thanks.
>>
>>> +
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL1);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_REGCTL2);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_THRES);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_MASK);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_INTERRUPT_STATUS);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_CONTROLLER_STATUS);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_ANALOG_CONTROL);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_AUX_DATA);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_CONTROL);
>>> + iproc_adc_dbg_reg(dev, adc_priv, IPROC_SOFT_BYPASS_DATA);
>>> +}
>>> +
>>> +static irqreturn_t iproc_adc_interrupt_handler(int irq, void *data)
>>> +{
>>> + u32 channel_intr_status;
>>> + u32 intr_status;
>>> + u32 intr_mask;
>>> + struct iio_dev *indio_dev = data;
>>> + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev);
>>> +
>>> + /*
>>> + * This interrupt is shared with the touchscreen driver.
>>> + * Make sure this interrupt is intended for us.
>>> + * Handle only ADC channel specific interrupts.
>>> + */
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status);
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &intr_mask);
>>> + intr_status = intr_status & intr_mask;
>>> + channel_intr_status = (intr_status & IPROC_ADC_INTR_MASK) >>
>>> + IPROC_ADC_INTR;
>>> + if (channel_intr_status)
>>> + return IRQ_WAKE_THREAD;
>>> +
>>> + return IRQ_NONE;
>>> +}
>>> +
>>> +static irqreturn_t iproc_adc_interrupt_thread(int irq, void *data)
>>> +{
>>> + irqreturn_t retval = IRQ_NONE;
>>> + struct iproc_adc_priv *adc_priv;
>>> + struct iio_dev *indio_dev = data;
>>> + unsigned int valid_entries;
>>> + u32 intr_status;
>>> + u32 intr_channels;
>>> + u32 channel_status;
>>> + u32 ch_intr_status;
>>> +
>>> + adc_priv = iio_priv(indio_dev);
>>> +
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_STATUS, &intr_status);
>>> + dev_dbg(&indio_dev->dev, "iproc_adc_interrupt_thread(),INTRPT_STS:%x\n",
>>> + intr_status);
>>> +
>>> + intr_channels = (intr_status & IPROC_ADC_INTR_MASK) >> IPROC_ADC_INTR;
>>> + if (intr_channels) {
>>> + regmap_read(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_INTERRUPT_STATUS +
>>> + IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id,
>>> + &ch_intr_status);
>>> +
>>> + if (ch_intr_status & IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK) {
>>> + regmap_read(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_STATUS +
>>> + IPROC_ADC_CHANNEL_OFFSET *
>>> + adc_priv->chan_id,
>>> + &channel_status);
>>> +
>>> + valid_entries = ((channel_status &
>>> + IPROC_ADC_CHANNEL_VALID_ENTERIES_MASK) >>
>>> + IPROC_ADC_CHANNEL_VALID_ENTERIES);
>>> + if (valid_entries >= 1) {
>>> + regmap_read(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_DATA +
>>> + IPROC_ADC_CHANNEL_OFFSET *
>>> + adc_priv->chan_id,
>>> + &adc_priv->chan_val);
>>> + complete(&adc_priv->completion);
>>> + } else {
>>> + dev_err(&indio_dev->dev,
>>> + "No data rcvd on channel %d\n",
>>> + adc_priv->chan_id);
>>> + }
>>> + regmap_write(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_INTERRUPT_MASK +
>>> + IPROC_ADC_CHANNEL_OFFSET *
>>> + adc_priv->chan_id,
>>> + (ch_intr_status &
>>> + ~(IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK)));
>>> + }
>>> + regmap_write(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_INTERRUPT_STATUS +
>>> + IPROC_ADC_CHANNEL_OFFSET * adc_priv->chan_id,
>>> + ch_intr_status);
>>> + regmap_write(adc_priv->regmap, IPROC_INTERRUPT_STATUS,
>>> + intr_channels);
>>> + retval = IRQ_HANDLED;
>>> + }
>>> +
>>> + return retval;
>>> +}
>>> +
>>> +static int iproc_adc_do_read(struct iio_dev *indio_dev,
>>> + int channel,
>>> + u16 *p_adc_data)
>>> +{
>>> + int read_len = 0;
>>> + u32 val;
>>> + u32 mask;
>>> + u32 val_check;
>>> + int failed_cnt = 0;
>>> + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev);
>>> +
>>> + mutex_lock(&adc_priv->mutex);
>>> +
>>> + /*
>>> + * After a read is complete the ADC interrupts will be disabled so
>>> + * we can assume this section of code is safe from interrupts.
>>> + */
>>> + adc_priv->chan_val = -1;
>>> + adc_priv->chan_id = channel;
>>> +
>>> + reinit_completion(&adc_priv->completion);
>>> + /* Clear any pending interrupt */
>>> + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS,
>>> + IPROC_ADC_INTR_MASK | IPROC_ADC_AUXDATA_RDY_INTR,
>>> + ((0x0 << channel) << IPROC_ADC_INTR) |
>>> + IPROC_ADC_AUXDATA_RDY_INTR);
>>> +
>>> + /* Configure channel for snapshot mode and enable */
>>> + val = (BIT(IPROC_ADC_CHANNEL_ROUNDS) |
>>> + (IPROC_ADC_CHANNEL_MODE_SNAPSHOT << IPROC_ADC_CHANNEL_MODE) |
>>> + (0x1 << IPROC_ADC_CHANNEL_ENABLE));
>>> +
>>> + mask = IPROC_ADC_CHANNEL_ROUNDS_MASK | IPROC_ADC_CHANNEL_MODE_MASK |
>>> + IPROC_ADC_CHANNEL_ENABLE_MASK;
>>> + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL1 +
>>> + IPROC_ADC_CHANNEL_OFFSET * channel),
>>> + mask, val);
>>> +
>>> + /* Set the Watermark for a channel */
>>> + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_REGCTL2 +
>>> + IPROC_ADC_CHANNEL_OFFSET * channel),
>>> + IPROC_ADC_CHANNEL_WATERMARK_MASK,
>>> + 0x1);
>>> +
>>> + /* Enable water mark interrupt */
>>> + regmap_update_bits(adc_priv->regmap, (IPROC_ADC_CHANNEL_INTERRUPT_MASK +
>>> + IPROC_ADC_CHANNEL_OFFSET *
>>> + channel),
>>> + IPROC_ADC_CHANNEL_WTRMRK_INTR_MASK,
>>> + IPROC_ADC_WATER_MARK_INTR_ENABLE);
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val);
>>> +
>>> + /* Enable ADC interrupt for a channel */
>>> + val |= (BIT(channel) << IPROC_ADC_INTR);
>>> + regmap_write(adc_priv->regmap, IPROC_INTERRUPT_MASK, val);
>>> +
>>> + /*
>>> + * There seems to be a very rare issue where writing to this register
>>> + * does not take effect. To work around the issue we will try multiple
>>> + * writes. In total we will spend about 10*10 = 100 us attempting this.
>>> + * Testing has shown that this may loop a few time, but we have never
>>> + * hit the full count.
>>> + */
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check);
>>> + while (val_check != val) {
>>> + failed_cnt++;
>>> +
>>> + if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS)
>>> + break;
>>> +
>>> + udelay(10);
>>> + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK,
>>> + IPROC_ADC_INTR_MASK,
>>> + ((0x1 << channel) <<
>>> + IPROC_ADC_INTR));
>>> +
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check);
>>> + }
>>> +
>>> + if (failed_cnt) {
>>> + dev_dbg(&indio_dev->dev,
>>> + "IntMask failed (%d times)", failed_cnt);
>>> + if (failed_cnt > IPROC_ADC_INTMASK_RETRY_ATTEMPTS) {
>>> + dev_err(&indio_dev->dev,
>>> + "IntMask set failed. Read will likely fail.");
>>> + read_len = -EIO;
>>> + goto adc_err;
>>> + };
>>> + }
>>> + regmap_read(adc_priv->regmap, IPROC_INTERRUPT_MASK, &val_check);
>>> +
>>> + if (wait_for_completion_timeout(&adc_priv->completion,
>>> + IPROC_ADC_READ_TIMEOUT) > 0) {
>>> +
>>> + /* Only the lower 16 bits are relevant */
>>> + *p_adc_data = adc_priv->chan_val & 0xFFFF;
>>> + read_len = sizeof(*p_adc_data);
>>> +
>>> + } else {
>>> + /*
>>> + * We never got the interrupt, something went wrong.
>>> + * Perhaps the interrupt may still be coming, we do not want
>>> + * that now. Lets disable the ADC interrupt, and clear the
>>> + * status to put it back in to normal state.
>>> + */
>>> + read_len = -ETIMEDOUT;
>>> + goto adc_err;
>>> + }
>>> + mutex_unlock(&adc_priv->mutex);
>>> +
>>> + return read_len;
>>> +
>>> +adc_err:
>>> + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_MASK,
>>> + IPROC_ADC_INTR_MASK,
>>> + ((0x0 << channel) << IPROC_ADC_INTR));
>>> +
>>> + regmap_update_bits(adc_priv->regmap, IPROC_INTERRUPT_STATUS,
>>> + IPROC_ADC_INTR_MASK,
>>> + ((0x0 << channel) << IPROC_ADC_INTR));
>>> +
>>> + dev_err(&indio_dev->dev, "Timed out waiting for ADC data!\n");
>>> + iproc_adc_reg_dump(indio_dev);
>>> + mutex_unlock(&adc_priv->mutex);
>>> +
>>> + return read_len;
>>> +}
>>> +
>>> +static int iproc_adc_enable(struct iio_dev *indio_dev)
>>> +{
>>> + u32 val;
>>> + u32 channel_id;
>>> + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev);
>>> + int ret;
>>> +
>>> + /* Set i_amux = 3b'000, select channel 0 */
>>> + ret = regmap_update_bits(adc_priv->regmap, IPROC_ANALOG_CONTROL,
>>> + IPROC_ADC_CHANNEL_SEL_MASK, 0);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write IPROC_ANALOG_CONTROL %d\n", ret);
>>> + return ret;
>>> + }
>>> + adc_priv->chan_val = -1;
>>> +
>>> + /*
>>> + * PWR up LDO, ADC, and Band Gap (0 to enable)
>>> + * Also enable ADC controller (set high)
>>> + */
>>> + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to read IPROC_REGCTL2 %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + val &= ~(IPROC_ADC_PWR_LDO | IPROC_ADC_PWR_ADC | IPROC_ADC_PWR_BG);
>>> +
>>> + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write IPROC_REGCTL2 %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to read IPROC_REGCTL2 %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + val |= IPROC_ADC_CONTROLLER_EN;
>>> + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write IPROC_REGCTL2 %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + for (channel_id = 0; channel_id < indio_dev->num_channels;
>>> + channel_id++) {
>>> + ret = regmap_write(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_INTERRUPT_MASK +
>>> + IPROC_ADC_CHANNEL_OFFSET * channel_id, 0);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write ADC_CHANNEL_INTERRUPT_MASK %d\n",
>>> + ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = regmap_write(adc_priv->regmap,
>>> + IPROC_ADC_CHANNEL_INTERRUPT_STATUS +
>>> + IPROC_ADC_CHANNEL_OFFSET * channel_id, 0);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write ADC_CHANNEL_INTERRUPT_STATUS %d\n",
>>> + ret);
>>> + return ret;
>>> + }
>>> + }
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static void iproc_adc_disable(struct iio_dev *indio_dev)
>>> +{
>>> + u32 val;
>>> + int ret;
>>> + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev);
>>> +
>>> + ret = regmap_read(adc_priv->regmap, IPROC_REGCTL2, &val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to read IPROC_REGCTL2 %d\n", ret);
>>> + return;
>>> + }
>>> +
>>> + val &= ~IPROC_ADC_CONTROLLER_EN;
>>> + ret = regmap_write(adc_priv->regmap, IPROC_REGCTL2, val);
>>> + if (ret) {
>>> + dev_err(&indio_dev->dev,
>>> + "failed to write IPROC_REGCTL2 %d\n", ret);
>>> + return;
>>> + }
>>> +}
>>> +
>>> +static int iproc_adc_read_raw(struct iio_dev *indio_dev,
>>> + struct iio_chan_spec const *chan,
>>> + int *val,
>>> + int *val2,
>>> + long mask)
>>> +{
>>> + u16 adc_data;
>>> + int err;
>>> +
>>> + switch (mask) {
>>> + case IIO_CHAN_INFO_RAW:
>>> + err = iproc_adc_do_read(indio_dev, chan->channel, &adc_data);
>>> + if (err < 0)
>>> + return err;
>>> + *val = adc_data;
>>> + return IIO_VAL_INT;
>>> + case IIO_CHAN_INFO_SCALE:
>>> + switch (chan->type) {
>>> + case IIO_VOLTAGE:
>>> + *val = 1800;
>>> + *val2 = 10;
>>> + return IIO_VAL_FRACTIONAL_LOG2;
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> + default:
>>> + return -EINVAL;
>>> + }
>>> +}
>>> +
>>> +static const struct iio_info iproc_adc_iio_info = {
>>> + .read_raw = &iproc_adc_read_raw,
>>> + .driver_module = THIS_MODULE,
>>> +};
>>> +
>>> +#define IPROC_ADC_CHANNEL(_index, _id) { \
>>> + .type = IIO_VOLTAGE, \
>>> + .indexed = 1, \
>>> + .channel = _index, \
>>> + .info_mask_separate = BIT(IIO_CHAN_INFO_RAW), \
>>> + .info_mask_shared_by_type = BIT(IIO_CHAN_INFO_SCALE), \
>>> + .datasheet_name = _id, \
>>> +}
>>> +
>>> +static const struct iio_chan_spec iproc_adc_iio_channels[] = {
>>> + IPROC_ADC_CHANNEL(0, "adc0"),
>>> + IPROC_ADC_CHANNEL(1, "adc1"),
>>> + IPROC_ADC_CHANNEL(2, "adc2"),
>>> + IPROC_ADC_CHANNEL(3, "adc3"),
>>> + IPROC_ADC_CHANNEL(4, "adc4"),
>>> + IPROC_ADC_CHANNEL(5, "adc5"),
>>> + IPROC_ADC_CHANNEL(6, "adc6"),
>>> + IPROC_ADC_CHANNEL(7, "adc7"),
>>> +};
>>> +
>>> +static int iproc_adc_probe(struct platform_device *pdev)
>>> +{
>>> + struct iproc_adc_priv *adc_priv;
>>> + struct iio_dev *indio_dev = NULL;
>>> + int ret;
>>> +
>>> + indio_dev = devm_iio_device_alloc(&pdev->dev,
>>> + sizeof(*adc_priv));
>>> + if (!indio_dev) {
>>> + dev_err(&pdev->dev, "failed to allocate iio device\n");
>>> + return -ENOMEM;
>>> + }
>>> +
>>> + adc_priv = iio_priv(indio_dev);
>>> + platform_set_drvdata(pdev, indio_dev);
>>> +
>>> + mutex_init(&adc_priv->mutex);
>>> +
>>> + init_completion(&adc_priv->completion);
>>> +
>>> + adc_priv->regmap = syscon_regmap_lookup_by_phandle(pdev->dev.of_node,
>>> + "adc-syscon");
>>> + if (IS_ERR(adc_priv->regmap)) {
>>> + dev_err(&pdev->dev, "failed to get handle for tsc syscon\n");
>>> + ret = PTR_ERR(adc_priv->regmap);
>>> + return ret;
>>> + }
>>> +
>>> + adc_priv->adc_clk = devm_clk_get(&pdev->dev, "tsc_clk");
>>> + if (IS_ERR(adc_priv->adc_clk)) {
>>> + dev_err(&pdev->dev,
>>> + "failed getting clock tsc_clk\n");
>>> + ret = PTR_ERR(adc_priv->adc_clk);
>>> + return ret;
>>> + }
>>> +
>>> + adc_priv->irqno = platform_get_irq(pdev, 0);
>>> + if (adc_priv->irqno <= 0) {
>>> + dev_err(&pdev->dev, "platform_get_irq failed\n");
>>> + ret = -ENODEV;
>>> + return ret;
>>> + }
>>> +
>>> + ret = regmap_update_bits(adc_priv->regmap, IPROC_REGCTL2,
>>> + IPROC_ADC_AUXIN_SCAN_ENA, 0);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "failed to write IPROC_REGCTL2 %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = devm_request_threaded_irq(&pdev->dev, adc_priv->irqno,
>>> + iproc_adc_interrupt_thread,
>>> + iproc_adc_interrupt_handler,
>>> + IRQF_SHARED, "iproc-adc", indio_dev);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "request_irq error %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = clk_prepare_enable(adc_priv->adc_clk);
>>> + if (ret) {
>>> + dev_err(&pdev->dev,
>>> + "clk_prepare_enable failed %d\n", ret);
>>> + return ret;
>>> + }
>>> +
>>> + ret = iproc_adc_enable(indio_dev);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "failed to enable adc %d\n", ret);
>>> + goto err_adc_enable;
>>> + }
>>> +
>>> + indio_dev->name = dev_name(&pdev->dev);
>> This name should reflect the part name rather than anything else.
>> Here this is easy as there is only one part name. I'd just put
>> it in directly here.
>
> I thought putting in the part name directly here would hard code and
> looked at the other ADC IIO drivers and found to be using the dev_name()
> call.
Yeah, that's a bit of an oops.
>
> "adc: adc@180a6000" this is the current node name used for adc in .dts file
> so it will take adc@180a6000 as the name and export it to sysfs.
>
> If I have to put the name directly then it should look like "adc" ??
> or "iproc-static-adc" ?
> then there wouldn't be a direct reference to the device name in .dts file.
iproc-static-adc preferred. The fact it is adc is way to generic.
The idea is that it is a loosely human readable indicator of which of a set
of ADCs on a board we are looking at. It's not ideal as there might be
more than one of a type, but better than nothing perhaps.
The devicetree name is easily found for a device:
Stealing from a recent example posted by Leonard in the thread
[was iio: tmp006: Set correct iio name] how to support multiple instances of same device type
# ssh -t local2222 udevadm info /sys/bus/iio/devices/iio:device0
DEVNAME=/dev/iio:device0
DEVTYPE=iio_device
MAJOR=250
MINOR=0
OF_COMPATIBLE_0=inv,mpu6500
OF_COMPATIBLE_N=1
OF_FULLNAME=/spi/mpu6500@0
OF_NAME=mpu6500
SUBSYSTEM=iio
>
> So I think it's better to keep the name captured from the call
> dev_name(&pdev->dev);
>
> Please suggest whether to put the name directly or keep the existing method.
Direct name please.
>
>>> + indio_dev->dev.parent = &pdev->dev;
>>> + indio_dev->dev.of_node = pdev->dev.of_node;
>>> + indio_dev->info = &iproc_adc_iio_info;
>>> + indio_dev->modes = INDIO_DIRECT_MODE;
>>> + indio_dev->channels = iproc_adc_iio_channels;
>>> + indio_dev->num_channels = ARRAY_SIZE(iproc_adc_iio_channels);
>>> +
>>> + ret = iio_device_register(indio_dev);
>>> + if (ret) {
>>> + dev_err(&pdev->dev, "iio_device_register failed:err %d\n", ret);
>>> + goto err_clk;
>>> + }
>>> +
>>> + return 0;
>>> +
>>> +err_clk:
>>> + iproc_adc_disable(indio_dev);
>>> +err_adc_enable:
>>> + clk_disable_unprepare(adc_priv->adc_clk);
>>> +
>>> + return ret;
>>> +}
>>> +
>>> +static int iproc_adc_remove(struct platform_device *pdev)
>>> +{
>>> + struct iio_dev *indio_dev = platform_get_drvdata(pdev);
>>> + struct iproc_adc_priv *adc_priv = iio_priv(indio_dev);
>>> +
>>> + iio_device_unregister(indio_dev);
>>> + iproc_adc_disable(indio_dev);
>>> + clk_disable_unprepare(adc_priv->adc_clk);
>>> +
>>> + return 0;
>>> +}
>>> +
>>> +static const struct of_device_id iproc_adc_of_match[] = {
>>> + {.compatible = "brcm,iproc-static-adc", },
>>> + { },
>>> +};
>>> +MODULE_DEVICE_TABLE(of, iproc_adc_of_match);
>>> +
>>> +static struct platform_driver iproc_adc_driver = {
>>> + .probe = iproc_adc_probe,
>>> + .remove = iproc_adc_remove,
>>> + .driver = {
>>> + .name = "iproc-static-adc",
>>> + .of_match_table = of_match_ptr(iproc_adc_of_match),
>>> + },
>>> +};
>> 1 blank line is always enough. Here actually, no blank lines is
>> the convention given the connection between the next line and the
>> structure.
>
> Yes, will fix it in the next patch.
>
>>> +
>>> +
>>> +module_platform_driver(iproc_adc_driver);
>>> +
>>> +MODULE_DESCRIPTION("IPROC ADC driver");
>>> +MODULE_AUTHOR("Broadcom");
>> Module author should be an individual ideally (it's an email address
>> to pester!) Given you are signing off, you are the obvious choice.
>> If several people were involved, you can have multiple MODULE_AUTHOR
>> entries. One person for each one though.
>
> Yes, will fix it in the next patch.
>
>>> +MODULE_LICENSE("GPL v2");
>>>
>>